BS ISO 8528-8-2016 Reciprocating internal combustion engine driven alternating current generating sets Requirements and tests for low-power generating sets《往复式内燃机驱动的交流发电机组 低功率发电机组要.pdf

《BS ISO 8528-8-2016 Reciprocating internal combustion engine driven alternating current generating sets Requirements and tests for low-power generating sets《往复式内燃机驱动的交流发电机组 低功率发电机组要.pdf》由会员分享，可在线阅读，更多相关《BS ISO 8528-8-2016 Reciprocating internal combustion engine driven alternating current generating sets Requirements and tests for low-power generating sets《往复式内燃机驱动的交流发电机组 低功率发电机组要.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、BS ISO 8528-8:2016Reciprocating internalcombustion engine drivenalternating current generatingsetsPart 8: Requirements and tests for low-power generating setsBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS ISO 8528-8:2016 BRITISH STANDARDNational forewordThis Brit

2、ish Standard is the UK implementation of ISO 8528-8:2016.It supersedes BS 7698-8:1996 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee MCE/14, RIC engines.A list of organizations represented on this committee can beobtained on request to its secretary.Th

3、is publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2016.Published by BSI Standards Limited 2016ISBN 978 0 580 85836 9ICS 27.020; 29.160.40Compliance with a British Standard cannot c

4、onfer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 May 2016.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dBS ISO 8528-8:2016 ISO 2016Reciprocating internal combustion engine driv

5、en alternating current generating sets Part 8: Requirements and tests for low-power generating setsGroupes lectrognes courant alternatif entrans par moteurs alternatifs combustion interne Partie 8: Prescriptions et essais pour groupes lectrognes de faible puissanceINTERNATIONAL STANDARDISO8528-8Seco

6、nd edition2016-05-15Reference numberISO 8528-8:2016(E)BS ISO 8528-8:2016ISO 8528-8:2016(E)ii ISO 2016 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2016, Published in SwitzerlandAll rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise

7、 in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCh. de

8、 Blandonnet 8 CP 401CH-1214 Vernier, Geneva, SwitzerlandTel. +41 22 749 01 11Fax +41 22 749 09 47copyrightiso.orgwww.iso.orgBS ISO 8528-8:2016ISO 8528-8:2016(E)Foreword iv1 Scope . 12 Normative references 13 Terms and definitions . 24 Regulations and additional requirements. 35 General notes on test

9、s . 36 Mechanical and electrical design (requirements and tests) . 36.1 General . 36.2 Electrical equipment 46.2.1 Generator 46.2.2 Connection of electric loads . 46.2.3 Screws and connections 46.3 Temperature rise . 46.3.1 General 46.3.2 Generator 46.3.3 RIC engines and other components . 56.4 Over

10、load conditions . 56.4.1 General 56.4.2 Uncontrolled generator 56.4.3 Controlled generator 56.5 Improper operation 57 Operating characteristics, power output, quality class and fuel consumption . 67.1 Standard reference conditions 67.2 Start-up and operating conditions . 67.3 Determination of perfor

11、mance class, quality class and fuel consumption . 77.3.1 Performance class . 77.3.2 Quality class . 77.3.3 Fuel consumption 77.4 Radio interference suppression . 7Bibliography 8 ISO 2016 All rights reserved iiiContents PageBS ISO 8528-8:2016ISO 8528-8:2016(E)ForewordISO (the International Organizati

12、on for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established ha

13、s the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The p

14、rocedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the edit

15、orial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent righ

16、ts identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an expla

17、nation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary informationThe committee responsible for this docum

18、ent is ISO/TC 70, Internal combustion engines.This second edition cancels and replaces the first edition (ISO 8528-8:1995), which has been technically revised.ISO 8528 consists of the following parts, under the general title, Reciprocating internal combustion engine driven alternating current genera

19、ting sets: Part 1: Application, ratings and performance Part 2: Engines Part 3: Alternating current generators for generating sets Part 4: Controlgear and switchgear Part 5: Generating sets Part 6: Test methods Part 7: Technical declarations for specification and design Part 8: Requirements and test

20、s for low-power generating sets Part 9: Measurement and evaluation of mechanical vibrations Part 10: Measurement of airborne noise by the enveloping surface method Part 12: Emergency power supply to safety services Part 13: Safetyiv ISO 2016 All rights reservedBS ISO 8528-8:2016INTERNATIONAL STANDAR

21、D ISO 8528-8:2016(E)Reciprocating internal combustion engine driven alternating current generating sets Part 8: Requirements and tests for low-power generating sets1 ScopeThis part of ISO 8528 defines design requirements, minimum performances and type tests for low-power generating sets driven by re

22、ciprocating internal combustion engines for land and marine use (domestic, recreational and industrial application), excluding generating sets used on aircraft.It concerns mainly low-power generating sets driven by reciprocating internal combustion engines for the generation of single or multiphase

23、alternating current or direct current up to 500 V. The generating sets are standard manufactured sets.In this part of ISO 8528, “low-power” is taken to mean rated power of a magnitude up to approximately 10 kW/50 Hz, 12 kW/60 Hz. Low-power generating sets, for the purpose of this International Stand

24、ard, are determined by the following special features: the users normally are laymen (for further details, see 3.1); the complete generating set is usually transportable or mobile; the electrical output is connected by means of plugs, sockets and screwed terminal except for extra low voltages; the g

25、enerating set is ready for use without any additional installation work by the user.Generating sets for special applications or of higher rated power conforming to the above special features may, by agreement between manufacturer and customer, be tested in accordance with this part of ISO 8528. If s

26、upplementary stipulations are required for certain applications, this is to be done taking this part of ISO 8528 as a basis.This part of ISO 8528 deals with the special requirements of design and test which are observed in addition to the definitions and requirements laid down in ISO 8528-1, ISO 852

27、8-2, ISO 8528-3, ISO 8528-4, ISO 8528-5 and ISO 8528-6, where applicable.This part of ISO 8528 does not deal with safety requirements in order to protect the user from dangers which are laid down in ISO 8528-13.NOTE This International Standard does not apply to arc welding equipment (IEC 60974 serie

28、s).2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any ame

29、ndments) applies.ISO 3046-1, Reciprocating internal combustion engines Performance Part 1: Declarations of power, fuel and lubricating oil consumptions, and test methods Additional requirements for engines for general useISO 8528-1:2005, Reciprocating internal combustion engine driven alternating cu

30、rrent generating sets Part 1: Application, ratings and performance ISO 2016 All rights reserved 1BS ISO 8528-8:2016ISO 8528-8:2016(E)ISO 8528-5:2013, Reciprocating internal combustion engine driven alternating current generating sets Part 5: Generating setsISO 8528-13:2016, Reciprocating internal co

31、mbustion engine driven alternating current generating sets Part-13: Safet yISO 15550:2002, Internal combustion engines Determination and method for the measurement of engine power General requirementsIEC 60034-1:2010, Rotating electrical machines Part 1: Rating and performanceIEC 60335-1:2013, House

32、hold and similar electrical appliances Safety Part 1: General requirementsIEC/TR 60083, Plugs and socket-outlets for domestic and similar general use Standardized in members countries of IECCISPR 12, Vehicles, boats and internal combustion engines Radio disturbances characteristics Limit3 Terms and

33、definitionsFor the purposes of this document, the following terms and definitions apply.3.1laymanperson who does not necessarily recognize potential danger resulting from electricity, moving parts or hot partsNote 1 to entry: The layman normally has a lack of training, knowledge and experience.Note

34、2 to entry: See also Clause 6.3.2power ratingelectric power available at the outlets or sockets of the generating sets, expressed in kilowatts (kW ) at the rated frequency and the rated power factor3.3rated powercontinuous power (COP) according to ISO 8528-1:2005, 13.3.1, as assigned by the generati

35、ng set manufacturerNote 1 to entry: The output voltage at the rated power should be within 10 % of the nominal rated voltage (i.e. the value on label).3.4maximum power MAXpower given by multiplying the current and voltage that the generating set is capable of delivering for at least 5 min within the

36、 voltage and frequency limitsNote 1 to entry: Prescribed output voltage shall be within 10% of the rated voltage and prescribed output frequency shall be within 8% of the rated frequency.Note 2 to entry: The protective device shall not be activated for a period of 5 min and the overload conditions s

37、hall meet the requirements of 6.4. The minimum ratio between the power rating (COP) and the maximum power (MAX) shall be Prated/Pmax 0,752 ISO 2016 All rights reservedBS ISO 8528-8:2016ISO 8528-8:2016(E)3.5thermal steady state conditionstate reached when the temperature rise of the generator does no

38、t vary by more than 2 K over a period of 1 hrNote 1 to entry: Under normal test conditions, the RIC engine has first reached a steady-state condition before a set of measurements is taken. If not, the permissible deviations for the steady-state conditions of the RIC engine according to ISO 3046-3 ap

39、ply.Note 2 to entry: For electrical parts, see IEC 60034-1:2010, 3.25; for RIC engines, see ISO 15550:2002, 6.2.4.3.2.3.6uncontrolled generatorgenerator on which there is no load- and speed-dependent adjustment of excitation by an automatic voltage regulator for control of terminal voltageNote 1 to

40、entry: This includes generators with directly acting load current-dependent excitation devices (compounding).3.7automatic voltage regulator-controlled generatorgenerator on which the terminal voltage is controlled by changing the excitation by means of an automatic voltage regulator as a function of

41、 load and speed alternatively, where the terminal voltage is controlled automatically by means of an inverter type of conversion system4 Regulations and additional requirementsFor low-power generating sets, additional regulations depending on the location of its operation shall exist. These shall re

42、fer to environmental and safety requirements defined in the laws and regulations of the legal authorities in the different countries where generating sets are used. The regulations are mainly in the following fields: noise emission limitation; exhaust gas emission limitation; electrical safety; fuel

43、 systems.5 General notes on testsTests according to this part of ISO 8528 are type tests, unless otherwise specified, the tests are made on a single sample as delivered, which shall withstand all the relevant tests.During the tests, the temperature of the ambient air shall be kept between 15C and 30

44、C.Generating sets built for more than one type of rated voltage, rated frequency or current shall be tested for all relevant operating parameters.6 Mechanical and electrical design (requirements and tests)6.1 GeneralThe requirements and tests of this part of ISO 8528 cover mechanical and electrical

45、performance.Acceptability of the component parts of the generating set shall be judged on the mechanical and electrical strength and resistance to ignition and distortion. ISO 2016 All rights reserved 3BS ISO 8528-8:2016ISO 8528-8:2016(E)6.2 Electrical equipment6.2.1 Generator6.2.1.1 Rating and perf

46、ormanceThe generator shall meet the requirements of IEC 60034-1 concerning duty type S1, covering rated values, irregularities of waveform, symmetry of voltages, capability of unbalanced load, temperature rise, dielectric properties and short circuit strength.Compliance shall be checked by checking

47、manufacturers documentation.6.2.1.2 Connection to stator or fieldAccess to brushes shall not be possible without tools. Screw caps or brush holders shall be screwed against a shoulder or a similar stop and grip with at least three full threads. Brush holders in which the brush is held in position by

48、 a locking facility shall be made in such a way as to ensure that locking is not dependent on brush spring pressure if loosening of the locking facility could give access to live parts.Screw caps of brush holders accessible from the outside surface of the generator shall be made of insulating materi

49、al or be covered by insulating material of suitable mechanical and electrical strength. They shall not project beyond the surrounding surface of the unit.Compliance shall be checked by visual inspection, mechanical test according to ISO 8528-13:2016, 6.12 and dielectric strength according to IEC 60335-1:2013, 13.6.2.2 Connection of electric loadsExcept for extra low voltages, low voltages plug-and-socket connections according to IEC/TR 60083 (single phase) and IEC 60309 (multiphase), or relevant n