BS ISO 7388-2-2007 Tool shanks with 7 24 taper for automatic tool changers Dimensions and designation of shanks of forms J JD and JF《自动工具转换用7 24锥度工具柄 J JD和JF型柄的尺寸规格和标志》.pdf

《BS ISO 7388-2-2007 Tool shanks with 7 24 taper for automatic tool changers Dimensions and designation of shanks of forms J JD and JF《自动工具转换用7 24锥度工具柄 J JD和JF型柄的尺寸规格和标志》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 7388-2-2007 Tool shanks with 7 24 taper for automatic tool changers Dimensions and designation of shanks of forms J JD and JF《自动工具转换用7 24锥度工具柄 J JD和JF型柄的尺寸规格和标志》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、 g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58Part 2: Dimensions and designation of shanks of forms J, JD and JFICS 25.060.20Tool shanks with 7/2

2、4 taper for automatic tool changers BRITISH STANDARDBS ISO 7388-2:2007BS ISO 7388-2:2007This British Standard was published under the authority of the Standards Policy and Strategy Committee on 28 September 2007 BSI 2007ISBN 978 0 580 56723 0Amendments issued since publicationAmd. No. Date Commentsc

3、ontract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.National forewordThis British Standard is the UK implementation of ISO 7388-2:2007. It supersedes BS 6607-2:1985 which is withdrawn.The UK participation in its

4、preparation was entrusted to Technical Committee MTE/1, Machine tools.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a Reference numberISO 7388-2:2007(E)INTERNATIONAL STAND

5、ARD ISO7388-2Second edition2007-08-01Tool shanks with 7/24 taper for automatic tool changers Part 2: Dimensions and designation of shanks of forms J, JD and JF Queues doutils conicit 7/24 pour changement automatique doutils Partie 2: Dimensions et dsignation des queues de formes J, JD et JF BS ISO 7

6、388-2:2007ii iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subje

7、ct for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC

8、) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committe

9、es are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be h

10、eld responsible for identifying any or all such patent rights. ISO 7388-2 was prepared by Technical Committee ISO/TC 29, Small tools. This second edition cancels and replaces the first edition (ISO 7388-2:1984), which has been technically revised. ISO 7388 consists of the following parts, under the

11、general title Tool shanks with 7/24 taper for automatic tool changers: Part 1: Dimensions and designation of shanks of forms A, AD, AF, U, UD and UF Part 2: Dimensions and designation of shanks of forms J, JD and JF Part 3: Retention knobs for shanks of forms AC, AD, AF, UC, UD, UF, JD and JF BS ISO

12、 7388-2:2007iv Introduction The aim of ISO 7388 is to integrate existing standards which are most commonly used as an industrial standard. In addition, the different developments for cooling and data chip have been taken into account. BS ISO 7388-2:20071Tool shanks with 7/24 taper for automatic tool

13、 changers Part 2: Dimensions and designation of shanks of forms J, JD and JF 1 Scope This part of ISO 7388 specifies the dimensions of tool shanks with a 7/24 taper of shank form J (with two possible additions for each) for automatic tool changers used on machines having an automatic gripping system

14、 for feeding tools from the magazine to the spindle and vice-versa. These tools are designed with the most important dimensions for use in spindle noses according to ISO 9270. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated

15、references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 2768-1, General tolerances Part 1: Tolerances for linear and angular dimensions without individual tolerance indications ISO 2768-2, General toler

16、ances Part 2: Geometrical tolerances for features without individual tolerance indications ISO 8015, Technical drawings Fundamental tolerancing principle 3 Dimensions 3.1 General All dimensions and tolerances are given in millimetres; tolerancing is according to ISO 8015. Tolerances not specified sh

17、all be of tolerance class “m” in accordance with ISO 2768-1 and of class “k” in accordance with ISO 2768-2. 3.2 Shank form J See Figure 1 and Table 1. BS ISO 7388-2:20072 Key 1 cutting edge 2 transition between taper and flange aPosition of the cutting edge for right hand tools with single cutting e

18、dge (can be rotated 180: symmetrical design). bAt the option of the manufacturer (radius or chamfer). cAt the manufacturers discretion. dScale: 2:1. eNot convex. Figure 1 Shank form J BS ISO 7388-2:20073Table 1 Dimensions of shanks of form J Shank number Dimension 30 40 45 50 60 b0,20+16,1 19,3 25,7

19、 d1a31, 75 44,45 57,15 69,85 107,95 d2H8 12,5 17 21 25 31 d400,538 53 73 85 135 d5h8 46 63 85 100 155 d6 0,0556,03 75,56 100,09 118,89 180,22 d76H M12 M16 M20 M24 M30 d88 10 12 15 20 d11max. 14,5 19 23,5 28 36 f b20 25 30 35 45 l1 0,2 48,4 65,4 82,8 101,8 161,8 l2min. 24 30 36 45 56 l3min. 34 43 50

20、62 76 l40,50+7 9 11 13 16 l5min. 17 21 26 31 34 l616,3 22,6 29,1 35,4 60,1 l6tol. 00,300,4l700,51,6 2 r10,5 1 r2c00,50,8 1 1,2 1,5 2 t10,001 0,002 0,003 t20,002 0,003 0,004 t30,12 0,2 u min. 22 27 33 38 48 v 0,1 13,6 16,6 21,2 23,2 28,2 x 4 5 6 7 11 y 0,4 d2 3 81750“ tol. 4“0+ad1: basic diameter enc

21、losed in a gauge plane. bFor information only. cChamfer or radius type of counterbore entrance are possible and limited by diameter d11. dTolerance 0,1 for form JF. BS ISO 7388-2:20074 3.3 Shank form JD As a complement to Form J, it is possible to add a through hole, e.g. for centric inner cooling l

22、ubricant supply, as indicated in Figure 2. This form is called JD. The condition is that d10shall be less than or equal to the core diameter of the thread receiving the retention knob. Figure 2 Shank form JD 3.4 Shank form JF As a complement to Form J, it is possible to add two holes at the back of

23、the flange for inner coolant supply, the dimensions of which are indicated in Figure 3 and Table 2. This form is called JF. If an auxiliary connecting bore is needed, it shall be sealed to withstand an operating pressure of up to 5 MPa, of a design that is at the manufacturers discretion. aDifferent

24、 from forms J and JD. Figure 3 Shank form JF BS ISO 7388-2:20075Table 2 Supplementary dimensions of shank form JF Shank no.d9max. e130 2 20 40 4 27 45 5 35 50 6 42 60 8 66 3.5 Shanks with data medium For the three shank forms defined in 3.2 to 3.4, it is possible to add a data medium, the dimensions

25、 of which are indicated in Figure 4 and Table 3. aThe fitting position of the data medium is the same position of the cutting edge as for right-hand tools with a single cutting edge. bOther diameter and depth according to the data medium used. Figure 4 Fitting position of the data medium Table 3 Sup

26、plementary dimensions for fitting data medium Shank no. Dimension 30 40 45 50 60 c amax. 0,3 45 or r 0,3 ad13100,090+l84,60,20+l911 14,5 18 20,5 aAt the discretion of the manufacturer. BS ISO 7388-2:20076 4 Information on material and heat treatment Tool shanks with a 7/24 taper should be heat treat

27、ed with considerations for strength, hardness, case depth (if not through hardened). Toughness and wear requirements are to be taken into account. 5 Designation A tool shank with 7/24 taper in accordance with this part of ISO 7388 shall be designated as follows: a) “Tool shank”; b) reference to this

28、 part of ISO 7388, i.e. “ISO 7388-2”; c) a dash; d) Form J, JD or JF; e) the size; f) in the case of a design with data medium, a dash and the letter D. EXAMPLE Designation of a tool shank with 7/24 in accordance with ISO 7388-2, Form J, shank no. 40, with fitting position for a data medium D: Tool

29、shank ISO 7388-2 J 40 D BS ISO 7388-2:20077Bibliography 1 ISO 9270 1), 7/24 tapers for tool shanks for automatic changing Tapers for spindle noses 1) It is intended that at the next revision, shanks of forms U, UD, UF, J, JD and LF will also be covered. BS ISO 7388-2:2007BS ISO BSI389 Chiswick High

30、RoadLondonW4 4AL7388-2:2007BSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by a

31、mendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard

32、 would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the

33、latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In re

34、sponse to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards throug

35、h its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BS

36、I are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online ac

37、cess to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standar

38、dization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI.This does not preclu

39、de the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.