BS ISO 7365-2012 Shipbuilding and marine structures Deck machinery Towing winches for deep sea use《造船与海上结构 甲板机械 深海用拖曳绞车》.pdf
《BS ISO 7365-2012 Shipbuilding and marine structures Deck machinery Towing winches for deep sea use《造船与海上结构 甲板机械 深海用拖曳绞车》.pdf》由会员分享,可在线阅读,更多相关《BS ISO 7365-2012 Shipbuilding and marine structures Deck machinery Towing winches for deep sea use《造船与海上结构 甲板机械 深海用拖曳绞车》.pdf(18页珍藏版)》请在麦多课文档分享上搜索。
1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS ISO 7365:2012Shipbuilding and marinestructures Deck machinery Towing winches for deepsea useBS ISO 7365:2012 BRITISH STANDARDNational forewordThis British Standard is the UK i
2、mplementation of ISO 7365:2012. The UK participation in its preparation was entrusted to TechnicalCommittee SME/32/-/4, Ships and marine technology - Outfitting and deck machinery.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does
3、not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2012. Published by BSI Standards Limited 2012ISBN 978 0 580 72824 2 ICS 47.020.50 Compliance with a British Standard cannot confer immunity from leg
4、al obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 November 2012.Amendments issued since publicationDate Text affectedBS ISO 7365:2012 ISO 2012Shipbuilding and marine structures Deck machinery Towing winches for deep sea useCon
5、struction navale et structures maritimes Auxiliaires de pont Treuils de remorque pour haute merINTERNATIONAL STANDARDISO 7365Second edition 2012-07-01Reference numberISO 7365:2012(E)BS ISO 7365:2012ISO 7365:2012(E)ii ISO 2012 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2012All rights reserve
6、d. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester
7、.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 7365:2012ISO 7365:2012(E) ISO 2012 All rights reserved iiiContents PageForeword iv1 Scope 12 Normative references . 13 Terms and defin
8、itions . 13.1 General terms . 13.2 Types of winches (see Figure 1) 14 Design and operation . 44.1 Material stresses . 44.2 Basic calculation . 44.3 Load alarm device . 44.4 Brakes . 44.5 Drum design . 54.6 Auxiliary equipment 64.7 Speed control . 64.8 Emergency release . 65 Performance specification
9、s 75.1 Load requirements 75.2 Speeds 76 Acceptance tests . 76.1 Drum brake holding test 76.2 Operation under load . 76.3 Control system utility test . 86.4 Emergency release test . 87 Designation system 87.1 Designation of product models . 87.2 Nameplate 8BS ISO 7365:2012ISO 7365:2012(E)ForewordISO
10、(the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical comm
11、ittee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrote
12、chnical standardization.International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member
13、 bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying
14、any or all such patent rights.ISO 7365 was prepared by Technical Committee ISO/TC 8, Ships and marine technology, Subcommittee SC 4, Outfitting and deck machinery.This second edition cancels and replaces the first edition (ISO 7365:1983), which has been technically revised.iv ISO 2012 All rights res
15、ervedBS ISO 7365:2012INTERNATIONAL STANDARD ISO 7365:2012(E)Shipbuilding and marine structures Deck machinery Towing winches for deep sea use1 ScopeThis International Standard specifies requirements for the design, operation, performance and acceptance tests of towing winches having electric, hydrau
16、lic, diesel or steam drive.It is applicable to towing winches for deep sea use.It does not consider fibre rope winches but does not exclude their use.2 Normative referencesThe following referenced documents are indispensable for the application of this document. For dated references, only the editio
17、n cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 2408, Steel wire ropes for general purposes Minimum requirementsISO 3828, Shipbuilding and marine structures Deck machinery Vocabulary and symbolsISO 6482, Shipbuilding Deck
18、machinery Warping end profiles3 Terms and definitionsFor the purposes of this document, the terms and definitions given in ISO 3828 and the following apply.3.1 General terms3.1.1nominal speedmaximum speed of hauling and rendering ropes maintained by winches under drum load3.1.2rendering loadmaximum
19、rope tension at the drum exit when the drum just starts to rotate in the opposite direction to the applied driving torque, the prime mover being set for limited torque, with a first layer of the rope wound on the drum3.2 Types of winches (see Figure 1)3.2.1right-hand winchwinch where the reduction g
20、ear or drive of the drum(s) is on the right-hand side of the drum(s), in relation to an observer situated on the side of the motor, power supply or local controller3.2.2left-hand winchwinch where the reduction gear or drive of the drum(s) is on the left-hand side of the drum, in relation to an obser
21、ver situated on the side of the motor, power supply or local controller3.2.3central winchwinch where the reduction gear or drive of the drum(s) is in the middle of the two drums ISO 2012 All rights reserved 1BS ISO 7365:2012ISO 7365:2012(E)3.2.4winch operable from both sideswinch where the reduction
22、 gear or drive of the drum(s) is on both sides of the drum3.2.5waterfall winchwinch where multiple drums are arranged from high to low3.2.6structural form of winchescode representing a winch related to the relative position of drums to power supply, drum quantity and height of drum centerNOTE 1 Stru
23、ctural form codes appear in brackets next to the subheadings in Figure 1.NOTE 2 The designation of structural form codes is shown in the diagram below.Single left-hand winch (L1) Single winch operable from both sides (B1) Single right-hand winch (R1)Double left-hand winch (L2) Double right-hand winc
24、h (R2)2 ISO 2012 All rights reservedBS ISO 7365:2012ISO 7365:2012(E)Double winch operable from both sides (B2)Double central winch (C2)Double left-hand waterfall winch (L2W)Double waterfall winch operable from both sides (B2W)Double right-hand waterfall winch (R2W)Triple left-hand waterfall winch (L
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BSISO73652012SHIPBUILDINGANDMARINESTRUCTURESDECKMACHINERYTOWINGWINCHESFORDEEPSEAUSE 造船 海上 结构 甲板 机械 深海

链接地址:http://www.mydoc123.com/p-587978.html