BS ISO 7364-2016 Ships and marine technology Deck machinery Accommodation ladder winches《船舶和海洋技术 甲板机械 舷梯绞车》.pdf

《BS ISO 7364-2016 Ships and marine technology Deck machinery Accommodation ladder winches《船舶和海洋技术 甲板机械 舷梯绞车》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 7364-2016 Ships and marine technology Deck machinery Accommodation ladder winches《船舶和海洋技术 甲板机械 舷梯绞车》.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS ISO 7364:2016Ships and marine technology Deck machinery Accommodation ladderwinchesBS ISO 7364:2016 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 7364:2016.The UK participation in its preparation was entrusted to TechnicalCommittee

2、 SME/32, Ships and marine technology - Steeringcommittee.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The Brit

3、ish Standards Institution 2016.Published by BSI Standards Limited 2016ISBN 978 0 580 80634 6ICS 47.020.50Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 30 April 2

4、016.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dBS ISO 7364:2016 ISO 2016Ships and marine technology Deck machinery Accommodation ladder winchesNavires et technologie maritime Auxiliaires de pont Treuils pour chelles de coupeINTERNATIONAL STANDARDISO7364Second edition20

5、16-04-01Reference numberISO 7364:2016(E)BS ISO 7364:2016ISO 7364:2016(E)ii ISO 2016 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2016, Published in SwitzerlandAll rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by

6、 any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCh. de Blandonnet 8 CP 4

7、01CH-1214 Vernier, Geneva, SwitzerlandTel. +41 22 749 01 11Fax +41 22 749 09 47copyrightiso.orgwww.iso.orgBS ISO 7364:2016ISO 7364:2016(E)Foreword iv1 Scope . 12 Normative references 13 Terms and definitions . 14 Design and operation 25 Characteristics 36 Acceptance tests (individual) 46.1 General .

8、 46.2 Test without load (factory test) 46.3 Drum load test (factory test) 46.4 Static test under 1,5 holding load . 56.5 On board test and inspections . 57 Designation 5 ISO 2016 All rights reserved iiiContents PageBS ISO 7364:2016ISO 7364:2016(E)ForewordISO (the International Organization for Stand

9、ardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right

10、to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures us

11、ed to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules

12、of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identifie

13、d during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on th

14、e meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information.The committee responsible for this document is ISO/

15、TC 8, Ships and marine technology, Subcommittee SC 1, Lifesaving and fire protection.This second edition cancels and replaces the first edition (ISO 7364:1983), which has been technically revised.iv ISO 2016 All rights reservedBS ISO 7364:2016INTERNATIONAL STANDARD ISO 7364:2016(E)Ships and marine t

16、echnology Deck machinery Accommodation ladder winches1 ScopeThis International Standard specifies requirements and characteristics of ships accommodation ladder winches provided with hydraulic, pneumatic, electric or manual drive.This International Standard is applicable to the design and test of ac

17、commodation ladder winches.This International Standard does not include requirements for the prime mover used to operate the winch.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated refe

18、rences, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 2408, Steel wire ropes for general purposes Minimum requirementsISO 3828, Shipbuilding and marine structures Deck machinery Vocabulary and symbolsISO 5

19、488:2015, Ships and marine technology Accommodation laddersIEC 60092-401, Electrical installations in ships Part 401: Installation and test of completed installation3 Terms and definitionsFor the purposes of this document, the terms and definitions given in ISO 3828 and the following apply.3.1nomina

20、l sizeused as a designation of a winch in accordance with this International StandardNote 1 to entry: The nominal size corresponds to the drum load as given in Table 1.3.2drum loadmaximum rope tension in the rope or ropes at the drum exit either when the winch is hoisting an unloaded accommodation l

21、adder at the nominal speed, with the rope or ropes wound on the drum in a single layer, or when the winch is placing the accommodation ladder in its stowage position3.3holding loadin static mode of the winch, the maximum rope tension in the rope or ropes at the drum exit in a single layer, shall be

22、at least three times the drum load (3.2)3.4 Types of winches3.4.1right-hand winchwinch where the reduction gear or drive of the drum is on the right-hand side of the drum, in relation to an observer situated on the side of the motor or power supplyNote 1 to entry: See Figure 1. ISO 2016 All rights r

23、eserved 1BS ISO 7364:2016ISO 7364:2016(E)3.4.2left-hand winchwinch where the reduction gear or drive of the drum is on the left-hand side of the drum, in relation to an observer situated on the side of the motor or power supplyNote 1 to entry: See Figure 1.3.4.3symmetrical double drum winchwinch whe

24、re the reduction gear or drive of the drums is between symmetrically situated drumsNote 1 to entry: See Figure 1.Right-hand winch Left-hand winchRight-hand winch with a split drum Left-hand winch with a split drumSymmetrical double drum winchFigure 1 Examples of accommodation ladder winches4 Design

25、and operation4.1 The winches shall be equipped with one or two drums. The drum shall be a split drum where two ropes are to be wound on it.2 ISO 2016 All rights reservedBS ISO 7364:2016ISO 7364:2016(E)4.2 The drum length shall be such that the rope in effective working length can be wound on fully,

26、in not more than three layers, while the rope can be wound on fully, in not more than five layers.4.3 The drum diameter shall be not less than 14 times the rope diameter given in Table 1.4.4 The flange height shall be such that it will project at least 1,5 times the rope diameter beyond the outermos

27、t layer of the rope.4.5 Double drum winches intended for double flight accommodation ladders shall be fitted with a suitable device to allow independent holding, hoisting or lowering of each flight.4.6 The winch shall be provided with a device capable of holding the drum at 1,5 holding load. For pow

28、ered winches, such device shall automatically operate when the drive is being shut off or if the power fails. Manual lowering and hoisting of the accommodation ladder shall be possible. A self-braking worm gearbox (or equivalent) may be considered a holding device if agreed between the purchaser and

29、 the manufacturer.4.7 For design purposes, the drum shall be based on the use of 6 37 galvanized steel wire rope with fibre core of 1 770 N/mm2tensile grade, as specified in ISO 2408. Wire rope diameters are listed in Table 1. This requirement does not preclude the use of other types of rope in serv

30、ice.In every case, the safety factor of the rope shall be not less than five in relation to the holding load as specified in ISO 5488:2015, 6.1.3.NOTE Attention is drawn to the possibility of national authorities requiring a safety factor of more than five.4.8 The winch shall be designed to ensure t

31、hat all bearing surfaces and corresponding sliding and rotating component parts of the winch are lubricated during operation.4.9 Stresses in component parts of the winch being acted upon with the drum load and holding load shall not exceed 0,4 times the proof stress of the material.4.10 The winch sh

32、all be fitted with a local emergency stop.4.11 Powered winches shall also be also provided with manual drive.4.12 Winches shall be provided with safety precautions to protect the operator against the possibility of being struck by a revolving crank handle.4.13 Electrical equipment of winches shall b

33、e installed in accordance with IEC 60092-401.4.14 Winches shall not be made of asbestos-containing material.5 Characteristics5.1 The characteristics of the winch shall be as listed in Table 1.5.2 For powered winches, the nominal speed of hoisting the accommodation ladder shall be not less than 0,05

34、m/s.5.3 It shall be possible to continuously overload the drive of the winch by 1,5 times the drum load for 2 min when the accommodation ladder is being hoisted, without causing failure. ISO 2016 All rights reserved 3BS ISO 7364:2016ISO 7364:2016(E)5.4 When the accommodation ladder is being hoisted

35、or lowered, the emergency stop of the winch shall be carried out. And the winch shall stop instantly and reliably.Table 1 Performance dataNominal sizeDrum loadakNHolding loadakNWinch load test procedureSteel wire rope diameter actually selecteddmmMinimum rope strengtha(5 holding load) KNSteel wire r

36、ope diameterb,cmmSingle drumSplit drum or double drum5 5 15 75 12 11 6 6,3 18 90 13 11 8 8 25 125 16 13 10 10 30 150 18 13 1312 12,5 37, 5 188 20 13 1316 16 48 240 22 14(15) 14(15)20 20 60 300 24 16(15) 16(15)25 25 75 375 26 1630 30 90 450 28 16NOTE Choose the actual steel wire rope diameter of winc

37、hes according to the following case that the breaking load of steel wire rope shall be not less than five times the actual holding load of accommodation ladder winches.aFor winches working with two ropes, the listed values are the sum of the forces on each rope.bIn column 4, based on a holding load

38、safety factor of five, all values shall be selected in winch load test.cThe rope diameter given in column 4 is used only for static load test of winches with one rope according to 6.4.dThe rope diameter in brackets means that these values are included in national standard specifications.6 Acceptance

39、 tests (individual)6.1 GeneralThe winch shall be tested as a complete unit, i.e. prime mover, drum, gearing and controls. The results of tests shall be recorded in the certificate.6.2 Test without load (factory test)The winch shall be run without load for 10 min continuously, 5 min in each direction

40、. The temperature of bearings shall be checked.6.3 Drum load test (factory test)6.3.1 The winch shall be run under drum load through two lowering and hoisting cycles include haul-in operation, the length of the rope paid out being not less than one-third of the drum capacity. The results shall confo

41、rm to the requirements of 5.2.6.3.2 Continuously overload the drive of the winch by 1,5 times the drum load for 2 min. The results shall conform to the requirements of 5.3.4 ISO 2016 All rights reservedBS ISO 7364:2016ISO 7364:2016(E)6.3.3 When the accommodation ladder is being hoisted or lowered, t

42、he emergency stop of the winch shall be carried out once. The results shall conform to the requirements of 5.4. The following shall be checked:a) oil-tightness;b) input current or working pressure or hydraulic flow;c) nominal speed;d) presence of abnormal noise;e) correct operation of the control br

43、ake.6.4 Static test under 1,5 holding loadA load equivalent to the 1,5 holding load shall be applied, with the rope wound in a single layer on the drum. The holding device shall prevent rotation of the drum when subjected to this load.6.5 On board test and inspectionsThe winch shall be tested as a p

44、art of the complete accommodation ladder unit. The minimum extent of the test shall be as follows:a) twice hoisting the accommodation ladder up to its full height and lowering it (tested as in 6.3);b) holding a static load for the complete accommodation ladder unit loaded as specified in ISO 5488:20

45、15, 6.1.3.7 DesignationAccommodation ladder winches conforming to this International Standard shall be designated as follows:a) safety operation specification or points for attention and direction indication of the rope or ropes at the drum exit;b) name of product;c) name and label of manufacturer;d

46、) load limit, including drum load, holding load, drum capacity, hoisting speed, etc.;e) specification or type of product, including the following:1) type of drive (E - electric, P pneumatic, H - hydraulic, U - unpowered);2) nominal size (according to Table 1);3) type of winch: R right-hand; L left-h

47、and; D single drum; DD split drum; 2DS symmetrical double drum; ISO 2016 All rights reserved 5BS ISO 7364:2016ISO 7364:2016(E)EXAMPLE Designation of an electrically-driven accommodation ladder winch of nominal size 12, right-hand, with a single Split drum: Accommodation ladder winch ISO 7364-E-12RDD

48、.f) date of manufacture;g) stamp of ship inspection department.6 ISO 2016 All rights reservedBS ISO 7364:2016BS ISO 7364:2016ISO 7364:2016(E) ISO 2016 All rights reservedICS 47.020.50Price based on 6 pagesThis page deliberately left blankBSI is the national body responsible for preparing British Sta

49、ndards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in o