BS ISO 7299-1-2007 Diesel engines - End-mounting flanges for pumps - Fuel injection pumps《柴油发动机 泵用端面安装法兰 燃料油喷射泵》.pdf

《BS ISO 7299-1-2007 Diesel engines - End-mounting flanges for pumps - Fuel injection pumps《柴油发动机 泵用端面安装法兰 燃料油喷射泵》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 7299-1-2007 Diesel engines - End-mounting flanges for pumps - Fuel injection pumps《柴油发动机 泵用端面安装法兰 燃料油喷射泵》.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、 g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58Part 1: Fuel injection pumpsICS 43.060.40Diesel engines End-mounting flanges for pumps BRITISH STAN

2、DARDBS ISO 7299-1:2007BS ISO 7299-1:2007This British Standard was published under the authority of the Standards Policy and Strategy Committee on 29 June 2007 BSI 2007ISBN 978 0 580 52908 5Amendments issued since publicationAmd. No. Date CommentsThis publication does not purport to include all the n

3、ecessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.National forewordThis British Standard was published by BSI. It is the UK implementation of ISO 7299-1:2007. It partially supersedes B

4、S ISO 7299:1996 which will be withdrawn on publication of BS ISO 7299-2.The UK participation in its preparation was entrusted to Technical Committee MCE/22, Engines for road vehicles.A list of organizations represented on this committee can be obtained on request to its secretary.Reference numberISO

5、 7299-1:2007(E)INTERNATIONAL STANDARD ISO7299-1First edition2007-02-01Diesel engines End-mounting flanges for pumps Part 1: Fuel injection pumps Moteurs diesels Brides de montage des pompes Partie 1: Pompes dinjection de carburant BS ISO 7299-1:2007ii iiiContents Page Foreword iv 1 Scope . 1 2 Norma

6、tive references . 1 3 Dimensions and tolerances . 1 3.1 General. 1 3.2 Fuel injection pumps 2 BS ISO 7299-1:2007iv Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standar

7、ds is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take

8、 part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is

9、to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility

10、 that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 7299-1 was prepared by Technical Committee ISO/TC 22, Road vehicles, Subcommittee SC 7, Injection equipment and filters for use on roa

11、d vehicles. This first edition, together with the first edition of ISO 7299-2, cancels and replaces the second edition of ISO 7299 (ISO 7299:1996), which has been technically revised. ISO 7299 consists of the following parts, under the general title Diesel engines End-mounting flanges for pumps: Par

12、t 1: Fuel injection pumps Part 2: High-pressure supply pumps for common rail fuel injection systems BS ISO 7299-1:20071Diesel engines End-mounting flanges for pumps Part 1: Fuel injection pumps 1 Scope This International Standard specifies dimensional requirements for nine types of end-mounting flan

13、ges for fuel injection pumps (rotary, distributor and in-line fuel injection pumps) for use in diesel (compression-ignition) engines. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies

14、. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 6519, Diesel engines Fuel injection pumps Tapers for shaft ends and hubs 3 Dimensions and tolerances 3.1 General Engine manufacturers are encouraged to use the tolerance H8 for the female

15、register diameter. If functionally necessary, the tolerance g8 on the pump spigot diameter (d1in the figures) may be replaced by f7, and the tolerance H8 on the female register diameter may be replaced by H7, by mutual agreement between supplier and user. NOTE 1 The diameter d2 in the figures and ta

16、bles corresponds to the diameter d specified in ISO 6519. NOTE 2 The flange configuration can optionally be rotated relative to the pump housing. BS ISO 7299-1:20072 3.2 Fuel injection pumps 3.2.1 Type 1 end-mounting flange See Figure 1 and Table 1. Dimensions in millimetres Figure 1 Fuel injection

17、pumps Type 1 end-mounting flange Table 1 Fuel injection pumps Type 1 end-mounting flange Dimensions in millimetres l3d1g8 d2nom. l1 0,5 l2max. min. max. 12,5 11 50 or 68 17 or 20 26 24,5 13 16 BS ISO 7299-1:200733.2.2 Type 2 end-mounting flange See Figure 2 and Table 2. Dimensions in millimetres aTh

18、is is the optional flange outline. Figure 2 Fuel injection pumps Type 2 end-mounting flange Table 2 Fuel injection pumps Type 2 end-mounting flange Dimensions in millimetres l3d2g8 d2nom. l1 0,5 l2max. min. max. 12,5 11 17,4 16 50 17 or 20 26 24,5 12,5 11 17,4 16 68 17, 20 or 25 26 24,5 13 16 BS ISO

19、 7299-1:20074 3.2.3 Type 3 end-mounting flange See Figure 3 and Table 3. Dimensions in millimetres Figure 3 Fuel injection pumps Type 3 end-mounting flange Table 3 Fuel injection pumps Type 3 end-mounting flange Dimensions in millimetres d1d2l1l2l3g8 nom. 0,5 max. min. max. 9,5 a 8,2 a 12,5 11 17,4

20、16 50 or 68 17 or 20 26 24,5 13 16 aNon-preferred value; only for interchangeability with certain types of in-line pumps. BS ISO 7299-1:200753.2.4 Type 4 end-mounting flange See Figure 4 and Table 4. Dimensions in millimetres Figure 4 Fuel injection pumps Type 4 end-mounting flange Table 4 Fuel inje

21、ction pumps Type 4 end-mounting flange Dimensions in millimetres d1d2l1l2l3g8 nom. 0,5 max. min. max. 68 17 9,5 8 10 16 BS ISO 7299-1:20076 3.2.5 Type 5 end-mounting flange See Figure 5 and Table 5. Dimensions in millimetres Figure 5 Fuel injection pumps Type 5 end-mounting flange Table 5 Fuel injec

22、tion pumps Type 5 end-mounting flange Dimensions in millimetres d1d2l1l2l3g8 nom. 0,5 max. min. max. 74 or 76 17 9,5 8 8 10 BS ISO 7299-1:200773.2.6 Type 6 end-mounting flange See Figure 6 and Table 6. Dimensions in millimetres aThis option has three holes. Figure 6 Fuel injection pumps Type 6 end-m

23、ounting flange Table 6 Fuel injection pumps Type 6 end-mounting flange Dimensions in millimetres d1d2l1l2l3g8 nom. 1 max. min. max. 17 18 68, 97 or 112 20 or 22 4,5 7,5 24 26 BS ISO 7299-1:20078 3.2.7 Type 7 end-mounting flange See Figure 7 and Table 7. Dimensions in millimetres Figure 7 Fuel inject

24、ion pumps Type 7 end-mounting flange Table 7 Fuel injection pumps Type 7 end-mounting flange Dimensions in millimetres d1d2l1l2l3g8 nom. 0,5 max. min. max. 4,58,2 9,5 8,2 12,5 11 68 or 85 17, 20, 22 or 25 17,4 16 15 18 BS ISO 7299-1:200793.2.8 Type 8 end-mounting flange See Figure 8 and Table 8. Dim

25、ensions in millimetres aIf it is required to mount a fixed pump, engine manufacturers are encouraged to position the engine studs at true (theoretically correct) angles of 40 above and 20 below the horizontal centreline. Figure 8 Fuel injection pumps Type 8 end-mounting flange Table 8 Fuel injection

26、 pumps Type 8 end-mounting flange Dimensions in millimetres d1d2l1l2l3d3d4l4g8 nom. 0,5 max. min. max. nom. max. max. 9,58,213,5 12 or 20,5 95 or 107 20, 25, 30 or 35 18,5 17 130 156 62 115 35 or 4013,5 12 or 20,5 17 20 140 166 66 BS ISO 7299-1:200710 3.2.9 Type 9 end-mounting flange See Figure 9 an

27、d Table 9. Dimensions in millimetres aThis is the option with four holes. Figure 9 Fuel injection pumps Type 9 end-mounting flange Table 9 Fuel injection pumps Type 9 end-mounting flange Dimensions in millimetres d1d2l1l2l3g8 nom. 0,5 max. min. max. 68 or 85 25 26 24,5 15 18 BS ISO 7299-1:2007blankB

28、S ISO BSI389 Chiswick High RoadLondonW4 4AL7299-1:2007BSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish

29、 Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while

30、using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers

31、 automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI webs

32、ite at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and int

33、ernational standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi

34、-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Info

35、rmation regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications o

36、f the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission fr

37、om BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.