BS ISO 6621-5-2013 Internal combustion engines Piston rings Quality requirements《内燃机 活塞环 质量要求》.pdf

《BS ISO 6621-5-2013 Internal combustion engines Piston rings Quality requirements《内燃机 活塞环 质量要求》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 6621-5-2013 Internal combustion engines Piston rings Quality requirements《内燃机 活塞环 质量要求》.pdf（26页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS ISO 6621-5:2013Internal combustion engines Piston ringsPart 5: Quality requirementsBS ISO 6621-5:2013 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 6621-5:2013. Itsupersedes BS ISO 6621-5:2005 which is withdrawn.The UK participatio

2、n in its preparation was entrusted to TechnicalCommittee MCE/14/-/10, RIC engines - Cylinders, pistons and rings.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Us

3、ers are responsible for its correctapplication. The British Standards Institution 2013. Published by BSI StandardsLimited 2013ISBN 978 0 580 69378 6ICS 43.060.10Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of

4、theStandards Policy and Strategy Committee on 30 September 2013.Amendments issued since publicationDate Text affectedBS ISO 6621-5:2013 ISO 2013Internal combustion engines Piston rings Part 5: Quality requirementsMoteurs combustion interne Segments de piston Partie 5: Exigences de qualitINTERNATIONA

5、L STANDARDISO6621-5Third edition2013-10-01Reference numberISO 6621-5:2013(E)BS ISO 6621-5:2013ISO 6621-5:2013(E)ii ISO 2013 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2013All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in

6、any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCase posta

7、le 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 6621-5:2013ISO 6621-5:2013(E) ISO 2013 All rights reserved iiiContents PageForeword ivIntroduction v1 Scope . 12 Normative references 13 Terms and definitions . 24 V

8、isible defects 24.1 General . 24.2 Pores, cavities, and sand inclusions 24.3 Scratches, indentations, depressions, and cracks . 34.4 Edges 34.5 Other characteristics subject to visual inspection only 105 Material .115.1 Specifications. 115.2 Loss of tangential force under temperature effects .116 Ra

9、ised material caused by marking of rings 117 Machining of periphery and sides Unintentional deviation from ideal profile and flatness .127.1 General 127.2 Permissible deviations for peripheral surface profile .127.3 Permissible helix 13Bibliography .14BS ISO 6621-5:2013ISO 6621-5:2013(E)ForewordISO

10、(the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical comm

11、ittee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrote

12、chnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafte

13、d in accordance with the editorial rules of the ISO/IEC Directives, Part 2. www.iso.org/directivesAttention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Det

14、ails of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received. www.iso.org/patentsAny trade name used in this document is information given for the convenience of users and does not constitute an endorse

15、ment.The committee responsible for this document is ISO/TC 22, Road vehicles.This third edition cancels and replaces the second edition (ISO 6621-5:2005), of which it constitutes a minor revision.ISO 6621 consists of the following parts, under the general title Internal combustion engines Piston rin

16、gs: Part 1: Vocabulary Part 2: Inspection measuring principles Part 3: Material specifications Part 4: General specifications Part 5: Quality requirementsiv ISO 2013 All rights reservedBS ISO 6621-5:2013ISO 6621-5:2013(E)IntroductionThis International Standard is one of a number of series of Interna

17、tional Standards dealing with piston rings for reciprocating internal combustion engines. Others are ISO 6622, ISO 6623, ISO 6624, ISO 6625, ISO 6626, and ISO 6627.The common features and dimensional tables presented in this part of ISO 6621 constitute a broad range of variables, and the designer, i

18、n selecting a particular ring type, should bear in mind the conditions under which it will be required to operate. The designer also refers to the specifications and requirements of ISO 6621-3 and ISO 6621-4 before completing his selection.The difficulty of trying to define in absolute terms the qua

19、lity attainable in normal commercial manufacture of piston rings is well known. In this part of ISO 6621, the commonly encountered aspects of quality in terms of casting defects and other departures from ideal are quantified. Many minor defects are clearly quite acceptable; other defects because of

20、size or number are inadmissible. ISO 2013 All rights reserved vBS ISO 6621-5:2013BS ISO 6621-5:2013Internal combustion engines Piston rings Part 5: Quality requirements1 ScopeThis part of ISO 6621 specifies those quality aspects that are capable of definition but not normally found on a drawing spec

21、ification.It is applicable to the following: single-piece piston rings of grey cast iron or steel; multi-piece piston rings (oil control rings) consisting of cast iron parts and spring components; single-piece and multi-piece oil control rings of steel, i.e. oil control rings in the form of strip st

22、eel components or steel segments (rails) with spring expander components.In addition to specifying certain of the limits of acceptance relating to inspection measuring principles (covered by ISO 6621-2), this part of ISO 6621 also covers those features for which no recognized quantitative measuremen

23、t procedures exist and which are only checked visually with normal eyesight (spectacles if worn normally) and without magnification. Such features (superficial defects) are additional to the standard tolerances of ring width, radial wall thickness, and closed gap.This part of ISO 6621 does not estab

24、lish acceptable quality levels (AQL), it being left to manufacturer and client to decide the appropriate levels jointly. In this case, the recommendations of ISO 2859 are followed.This part of ISO 6621 specifies the quality requirements of piston rings for reciprocating internal combustion engines f

25、or road vehicles and other applications. It is applicable to all such rings of a nominal diameter from 30 mm up to and including 200 mm.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated

26、 references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 6621-1, Internal combustion engines Piston rings Part 1: VocabularyISO 6621-3, Internal combustion engines Piston rings Part 3: Material specifica

27、tionsISO 6622 (all parts), Internal combustion engines Piston ringsISO 6623, Internal combustion engines Piston rings Scraper rings made of cast ironISO 6624 (all parts), Internal combustion engines Piston ringsISO 6625, Internal combustion engines Piston rings Oil control ringsISO 6626, Internal co

28、mbustion engines Piston rings Coil-spring-loaded oil control ringsISO 6626-2, Internal combustion engines Piston rings Part 2: Coil-spring-loaded oil control rings of narrow width made of cast ironINTERNATIONAL STANDARD ISO 6621-5:2013(E) ISO 2013 All rights reserved 1BS ISO 6621-5:2013ISO 6621-5:20

29、13(E)ISO 6626-3, Internal combustion engines Piston rings Part 3: Coil-spring-loaded oil control rings made of steelISO 6627, Internal combustion engines Piston rings Expander/segment oil-control rings3 Terms and definitionsFor the purposes of this document, the terms and definitions in ISO 6621-1 a

30、pply.4 Visible defects4.1 GeneralVisible defects are divided into two principal classes as described in 4.2 to 4.5.The first class covers those defects frequently found in castings and includes such defects as porosity, sand inclusions, cavities, etc.The second class of defects covers mechanical abr

31、asions which may occur during forming, machining, or handling of the rings and includes scratches, dents, chipping, burrs, and cracks.Inspection of piston rings for such defects is generally carried out visually, without magnification, by inspectors having normal eyesight, corrected if necessary.It

32、is not intended that every ring be rigorously inspected for size and distribution of defects, but rather that the values given in the tables and text be used as a general guide. However, in case of doubt, the values given should be used as the means of judging the quality of the rings.4.2 Pores, cav

33、ities, and sand inclusionsSuch defects are permissible on uncoated surfaces and edges provided that the values given in Table 1 for size, number, and spacing are not exceeded.Table 1 Permissible values of size, number, and spacing of pores, cavities, and sand inclusionsDimensions in millimetresNomin

34、al diameter d1Defect size max.Number of defects per ring max.Spacing of defectscmin.On peripheral surfaceaOn other surfacesaOn peripheral edgesOn other edgesb30 d11,5 0,380 d1 125 0,5125 d1 175 0,7175 d1 200 1 ISO 2013 All rights reserved 13BS ISO 6621-5:2013ISO 6621-5:2013(E)Bibliography1 ISO 6621-

35、2, Internal combustion engines Piston rings Part 2: Inspection measuring principles2 ISO 6621-4, Internal combustion engines Piston rings Part 4: General specifications14 ISO 2013 All rights reservedBS ISO 6621-5:2013BS ISO 6621-5:2013ISO 6621-5:2013(E) ISO 2013 All rights reservedICS 43.060.10Price

36、 based on 14 pagesThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI S

37、tandards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge e

38、mbodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your

39、organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards,

40、 through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.SubscriptionsOur range of subscription services are designed to make using stan

41、dards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to da

42、te. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically rece

43、ive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as f

44、ew or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendment or revision. We continually improve the quality of our pro

45、ducts and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.CopyrightAll the data, software and documentation set out in all British Standards and other BSI publications are the property of

46、and copyrighted by BSI, or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988

47、no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. Details and advice can be obtained from the Copyright & Licensing Department.Useful Contacts:Customer ServicesTel: +44 845 086 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 845 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW