BS ISO 6133-2015 Rubber and plastics Analysis of multi-peak traces obtained in determinations of tear strength and adhesion strength《橡胶和塑料制品 测定撕裂强度和粘合强度获得的多峰值图形分析》.pdf

《BS ISO 6133-2015 Rubber and plastics Analysis of multi-peak traces obtained in determinations of tear strength and adhesion strength《橡胶和塑料制品 测定撕裂强度和粘合强度获得的多峰值图形分析》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 6133-2015 Rubber and plastics Analysis of multi-peak traces obtained in determinations of tear strength and adhesion strength《橡胶和塑料制品 测定撕裂强度和粘合强度获得的多峰值图形分析》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS ISO 6133:2015Rubber and plastics Analysis of multi-peak traces obtained in determinations of tear strength and adhesion strengthBS ISO 6133:2015 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 6133:2015. It supersedes BS ISO 6133:199

2、8 which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee PRI/22, Physical testing of rubber.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provis

3、ions of a contract. Users are responsible for its correct application. The British Standards Institution 2015. Published by BSI Standards Limited 2015ISBN 978 0 580 85585 6 ICS 83.060; 83.080.01 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard wa

4、s published under the authority of the Standards Policy and Strategy Committee on 31 August 2015.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dBS ISO 6133:2015 ISO 2015Rubber and plastics Analysis of multi-peak traces obtained in determinations of tear strength and adhesi

5、on strengthCaoutchouc et plastiques Analyse des tracs multi-pics obtenus lors des dterminations de la rsistance au dchirement et de la force dadhrenceINTERNATIONAL STANDARDISO6133Third edition2015-08-15Reference numberISO 6133:2015(E)BS ISO 6133:2015ISO 6133:2015(E)ii ISO 2015 All rights reservedCOP

6、YRIGHT PROTECTED DOCUMENT ISO 2015, Published in SwitzerlandAll rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, w

7、ithout prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCh. de Blandonnet 8 CP 401CH-1214 Vernier, Geneva, SwitzerlandTel. +41 22 749 01 11Fax +41 22 749 09 47copyrightiso.orgwww.iso.org

8、BS ISO 6133:2015ISO 6133:2015(E)Foreword iv1 Scope . 12 Terms and definitions . 13 Procedure. 13.1 General . 13.2 Method A 23.3 Method B 23.4 Method C 33.5 Method D 33.6 Method E 44 Trace-analysis report . 5 ISO 2015 All rights reserved iiiContents PageBS ISO 6133:2015ISO 6133:2015(E)ForewordISO (th

9、e International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committ

10、ee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechn

11、ical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted i

12、n accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.

13、Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute a

14、n endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information.The committee

15、 responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis.This third edition cancels and replaces the second edition (ISO 6133:1998), which has been technically revised to define the force difference for recognizing a peak.iv ISO 2015 All rights

16、 reservedBS ISO 6133:2015INTERNATIONAL STANDARD ISO 6133:2015(E)Rubber and plastics Analysis of multi-peak traces obtained in determinations of tear strength and adhesion strength1 ScopeThis International Standard specifies five methods of calculating, after testing, the tear strength and the adhesi

17、on strength of vulcanized rubber or fabrics coated with or adhered to rubber or plastics. The results are calculated by determining the median and range of peak values from a graphical plot of force versus time recorded during the test.A trace for an adhesion strength test or tear strength test can

18、show few or many force peaks, depending on the material under investigation. The choice of the method of calculation depends on the number of peaks in the trace.The purpose of this International Standard is to obtain more uniformity in the evaluation and presentation of test results. It is applicabl

19、e only, however, when specified in another International Standard, i.e. a method of test or a specification.For other details, such as apparatus, test piece preparation, conditioning, procedure, etc., requirements given in the relevant International Standard shall apply.NOTE In certain cases, the me

20、thods of analysis given might not be adequate, for example, for peak values showing a trend with time. In cases where the minimum force values are of interest, it is possible to use the same methods of calculation as when determining from a range of peak values.2 Terms and definitionsFor the purpose

21、s of this document, the following terms and definitions apply.2.1peakpoint at which the slope of a trace changes from positive to negativeNote 1 to entry: For example, a peak occurs when there is an instantaneous maximum force.2.2rangedifference between the greatest and the smallest observed values

22、of observed force peaks2.3complete tracesection of the graphical plot of force versus time between the time at which the first peak occurs and the time at which the test is terminated3 Procedure3.1 GeneralFrom the force peak values of the trace for adhesion strength or tear strength, determine the m

23、edian peak force and the range of peak force values by the appropriate method specified in 3.2, 3.3, or 3.4. A ISO 2015 All rights reserved 1BS ISO 6133:2015ISO 6133:2015(E)peak is taken as valid only if the force difference between the maximum and the following minimum is larger than 2 % of the max

24、imal force.NOTE In applying the methods described in this International Standard, it is assumed that the trace being evaluated is a time record of the variation of force during the period of test.When analysing the trace with a computer, filter the signal to avoid too many small peaks. This can be d

25、one by allowing the measured force to drop a certain percentage and allowing a certain time to pass before a new peak is registered. It might be necessary to adjust these factors when testing different materials in order to obtain about the same number of peaks as can be seen on a chart recorder.3.2

26、 Method AFor traces having less than five peaks.Determine the median, the range, the minimum and the maximum of the force peak values in the trace.If there is only one force peak, consider its value to be the median.3.3 Method BFor traces having five to 20 peaks (see Figure 1) or where peak values a

27、re automatically computed.Y1210 %80 %10 %XKeyX timeY force1 median2 rangeFigure 1 Analysis of a trace with five to 20 peaks2 ISO 2015 All rights reservedBS ISO 6133:2015ISO 6133:2015(E)Consider only the peak values of the central 80 % of the complete trace and determine the median peak force, the ra

28、nge, the minimum and the maximum of these values.NOTE Although it is possible to use this method for traces having more than 20 peaks, it is not recommended for manual calculations.3.4 Method CFor traces having more than 20 peaks which are clearly defined and can be readily measured (see Figure 2) a

29、nd which are not automatically computed.YX1233KeyX timeY force1 median2 range3 t/2Figure 2 Analysis of a trace with more than 20 clearly defined peaksDraw a series of nine vertical lines by starting at the centre of the complete trace and drawing four more lines on each side at equal distances of on

30、e-tenth of the length of the trace, to the nearest 1 mm. Consider only the peak value situated closest to each of the vertical lines. Determine the median peak force and the range, the minimum and the maximum of these nine values.3.5 Method DFor undulating traces (see Figure 3). ISO 2015 All rights

31、reserved 3BS ISO 6133:2015ISO 6133:2015(E)YX123KeyX timeY force1 mean2 maximum3 minimumFigure 3 Analysis of an undulating trace (range or median of no significance)Where the peaks are not clearly defined but form an undulating curve, report only the arithmetic mean value. Report this arithmetic mean

32、 value as the midpoint between the maximum and the minimum deflections of the trace, ignoring the initial rise at the start of the test.3.6 Method EFor traces too close for counting (see Figure 4).4 ISO 2015 All rights reservedBS ISO 6133:2015ISO 6133:2015(E)YX213KeyX timeY force1 mean (midpoint)2 h

33、ighest peak3 lowest peakFigure 4 Analysis of a trace with a large number of peaks (too close for counting)Where there are a large number of peaks which are clearly defined, but which are so close as to render their counting difficult, report only the arithmetic mean value. Report this arithmetic mea

34、n value as the midpoint between the highest and lowest peak, ignoring the initial rise at the start of the test.4 Trace-analysis reportThe trace-analysis report shall include the following information:a) reference to this International Standard, i.e. ISO 6133;b) reference to the test for which the c

35、alculation was made;c) method of calculation used (A, B, C, D, or E);d) median peak force or, for methods D and E, the mean value;e) range of peak values;f) date of the calculation. ISO 2015 All rights reserved 5BS ISO 6133:2015ISO 6133:2015(E) ISO 2015 All rights reservedICS 83.060; 83.080.01Price

36、based on 5 pagesThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Sta

37、ndards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge emb

38、odied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your or

39、ganization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, t

40、hrough our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.SubscriptionsOur range of subscription services are designed to make using standa

41、rds easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date

42、. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receiv

43、e the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few

44、 or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendment or revision. We continually improve the quality of our produ

45、cts and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.CopyrightAll the data, software and documentation set out in all British Standards and other BSI publications are the property of an

46、d copyrighted by BSI, or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no

47、 extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. Details and advice can be obtained from the Copyright & Licensing Department.Useful Contacts:Customer ServicesTel: +44 845 086 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 845 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW