BS ISO 5608-2012 Turning and copying tool holders and cartridges for indexable inserts Designation《螺纹铣刀片系列用旋转和仿形刀具架和暗盒 名称》.pdf

《BS ISO 5608-2012 Turning and copying tool holders and cartridges for indexable inserts Designation《螺纹铣刀片系列用旋转和仿形刀具架和暗盒 名称》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 5608-2012 Turning and copying tool holders and cartridges for indexable inserts Designation《螺纹铣刀片系列用旋转和仿形刀具架和暗盒 名称》.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS ISO 5608:2012Turning and copying toolholders and cartridgesfor indexable inserts DesignationBS ISO 5608:2012 BRITISH STANDARDNational forewordThis British Standard is the UK i

2、mplementation of ISO 5608:2012. Itsupersedes BS 4193-6:1997 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee MTE/18, Tools tips and inserts for cutting applications.A list of organizations represented on this committee can beobtained on request to its se

3、cretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2012. Published by BSI StandardsLimited 2012ISBN 978 0 580 76252 9ICS 25.060.20; 25.100.10Compliance with a British Stan

4、dard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 August 2012.Amendments issued since publicationDate T e x t a f f e c t e dBS ISO 5608:2012 ISO 2012Turning and copying tool holders and cartr

5、idges for indexable inserts DesignationPorte-plaquette de tournage et de copiage et cartouches pour plaquettes amovibles DsignationINTERNATIONAL STANDARDISO5608Fourth edition2012-08-15Reference numberISO 5608:2012(E)BS ISO 5608:2012ISO 5608:2012(E)ii ISO 2012 All rights reservedCOPYRIGHT PROTECTED D

6、OCUMENT ISO 2012All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member bo

7、dy in the country of the requester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 5608:2012ISO 5608:2012(E) ISO 2012 All rights reserved iiiContents PageForeword iv1 Scope 12 Explana

8、tion of the designation code . 12.1 General . 12.2 Letter and number symbols comprising the designation code 13 Compulsory symbols . 23.1 Symbol for the holding method of the horizontally mounted insert Reference position (1) . 23.2 Symbol for insert shape Reference position (2) 23.3 Symbol for tool

9、 style Reference position (3) 33.4 Symbol for the insert normal clearance Reference position (4) 53.5 Symbol for hand of tool Reference position 5 53.6 Symbol for tool height Reference position (6) . 53.7 Symbol for tool width Reference position (7) . 63.8 Symbol for tool length Reference position (

10、8) . 63.9 Symbol for indexable insert size Reference position (9) . 84 Optional symbol: symbol for special tolerances Reference position (10) . 8Annex A (informative) Relationship between designations in this International Standard and the ISO 13399 series 10Bibliography . 11BS ISO 5608:2012ISO 5608

11、:2012(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for wh

12、ich a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all

13、matters of electrotechnical standardization.International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circ

14、ulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsi

15、ble for identifying any or all such patent rights.ISO 5608 was prepared by Technical Committee ISO/TC 29, Small tools, Subcommittee SC 9, Tools with cutting edges made of hard cutting materials.This fourth edition cancels and replaces the third edition (ISO 5608:1995), which has been technically rev

16、ised.iv ISO 2012 All rights reservedBS ISO 5608:2012INTERNATIONAL STANDARD ISO 5608:2012(E)Turning and copying tool holders and cartridges for indexable inserts Designation1 ScopeThis International Standard establishes a code for the designation of turning and copying tool holders and cartridges wit

17、h a rectangular shank, having a standardized dimension, f (see ISO 5610-1, ISO 5610-2, ISO 5610-3, ISO 5610-4, ISO 5610-5, ISO 5610-6, ISO 5610-7, ISO 5610-8, ISO 5610-9, ISO 5610-10, ISO 5610-11, ISO 5610-12, ISO 5610-13, ISO 5610-14 and ISO 5610-15 and ISO 5611), intended for use with indexable in

18、serts, thus simplifying orders and specifications for such tools.The designation of boring bars (tool holders with cylindrical shank) is given in ISO 5609-1. 2 Explanation of the designation code2.1 GeneralThe designation code comprises 10 symbols for the designation of dimensions and other characte

19、ristics of the tool and the insert, of which the first nine symbols shall be used in any designation. The last symbol may be used where necessary.In addition to the standardized designation symbols in positions (1) to (10), a supplementary symbol consisting of a maximum of three letters and/or numbe

20、rs may be added by the manufacturer for a better description of his/her products, on condition that this symbol is separated from the standardized designation by a dash and that it does not contain letters specified for position (10).No addition to, or extension of, the code specified in this Intern

21、ational Standard shall be made without consulting and securing the agreement of ISO/TC 29. Rather than adding symbols not provided for in this system, it is preferable to add to the designation conforming with this International Standard all necessary explanations in detailed illustrations or specif

22、ications.2.2 Letter and number symbols comprising the designation code2.2.1 Compulsory letter and/or number symbolsa) (1): letter symbol identifying the method of holding the insert (see 3.1);b) (2): letter symbol identifying insert shape (see 3.2);c) (3): letter symbol identifying tool style (see 3

23、.3);d) (4): letter symbol identifying insert normal clearance (see 3.4);e) (5): letter symbol identifying hand of tool (see 3.5);f) (6): number symbol identifying tool height (shank height of tool holders and height of cutting edge) (see 3.6);g) (7): number symbol identifying tool holder shank width

24、 or, for cartridges, the letter C followed by a letter symbol identifying the cartridge type (see 3.7);h) (8): letter symbol identifying tool length (see 3.8);i) (9): letter symbol identifying indexable insert size (see 3.9). ISO 2012 All rights reserved 1BS ISO 5608:2012ISO 5608:2012(E)2.2.2 Option

25、al letter symbol(10): letter symbol indicating special tolerances (see Clause 4):EXAMPLE (1) (2) (3) (4) (5) (6) (7) (8) (9) (10)C T G N R 32 25 M 16 QNOTE The codes (2), (4) and (9) are in accordance with ISO 1832.3 Compulsory symbols3.1 Symbol for the holding method of the horizontally mounted ins

26、ert Reference position (1)Table 1Letter symbol Insert holding methodC Top clamping (insert without hole)M Top and hole clamping (insert with hole)P Hole clamping (insert with hole)S Screw clamping through hole (insert with hole)3.2 Symbol for insert shape Reference position (2)Table 2Letter symbol I

27、nsert shape Insert typeH HexagonalEquilateral and equiangularO OctagonalP PentagonalS SquareT TriangularC Rhombic with 80 included angleEquilateral and non-equiangularD Rhombic with 55 included angleE Rhombic with 75 included angleM Rhombic with 86 included angleV Rhombic with 35 included angleW Hex

28、agonal with 80 included angleL Rectangular Non-equilateral and equiangularA Parallelogram-shaped with 85 included angleNon-equilateral and non-equiangularB Parallelogram-shaped with 82 included angleK Parallelogram-shaped with 55 included angleR Round RoundNOTE The included angle is always the small

29、er angle.2 ISO 2012 All rights reservedBS ISO 5608:2012ISO 5608:2012(E)3.3 Symbol for tool style Reference position (3)Table 3 Letter symbol Tool styleA90 cutting edge angle, straight shank, for side cuttingB75 cutting edge angle, straight shank, for side cuttingC90 cutting edge angle, straight shan

30、k, for end cuttingDa45 cutting edge angle, straight shank, for side cuttingE60 cutting edge angle, straight shank, for side cuttingF90 cutting edge angle, offset shank, for end cuttingG90 cutting edge angle, offset shank, for side cuttingH107,5 cutting edge angle, offset shank, for side cuttingJ93 c

31、utting edge angle, offset shank, for side cuttingK75 cutting edge angle, offset shank, for end cutting ISO 2012 All rights reserved 3BS ISO 5608:2012ISO 5608:2012(E)Letter symbol Tool styleL95 cutting edge angles on both cutting edges, offset shank, for side and end cuttingM50 cutting edge angle, st

32、raight shank, for side cuttingN63 cutting edge angle, straight shank, for side cuttingP117,5 cutting edge angle, offset shank, for side cuttingR75 cutting edge angle, offset shank, for side cuttingSa45 cutting edge angle, offset shank, for side cuttingT60 cutting edge angle, offset shank, for side c

33、uttingU93 cutting edge angle, offset shank, for end cuttingV72,5 cutting edge angle, straight shank, for side cuttingW60 cutting edge angle, offset shank, for end cuttingY85 cutting edge angle, offset shank, for end cuttingaTools of styles D and S may also be equipped with round inserts (shape R).Ta

34、ble 3 (continued)4 ISO 2012 All rights reservedBS ISO 5608:2012ISO 5608:2012(E)3.4 Symbol for the insert normal clearance Reference position (4)Table 4Letter symbol Insert normal clearanceA 3B 5C 7D 15E 20F 25G 30N 0P 11NOTE For non-equilateral inserts, the letter symbol applies to the normal cleara

35、nce of the longer side.3.5 Symbol for hand of tool Reference position 5Table 5Letter symbol Hand of toolR Right handL Left handN Either hand3.6 Symbol for tool height Reference position (6)3.6.1 Tool holders with rectangular shank cross-section and height of cutting edge, h1, equal to shank height,

36、h For tool holders with rectangular shank cross-section and height of cutting edge, h1, equal to shank height, h, see Figure 1.The number symbol for the tool height is the value of the shank height, h, in millimetres. If the resulting symbol has only one digit, it shall be preceded by a zero (0).EXA

37、MPLE 1 For h = 32 mm, the symbol is 32EXAMPLE 2 For h = 8 mm, the symbol is 08Figure 1 ISO 2012 All rights reserved 5BS ISO 5608:2012ISO 5608:2012(E)3.6.2 Cartridges with height of cutting edge, h1, not equal to shank height, h For cartridges with height of cutting edge, h1, not equal to shank heigh

38、t, h, see Figure 2.The number symbol, f, or the tool height is the value of the height of the cutting edge, h1, in millimetres. If the resulting symbol has only one digit, it shall be preceded by a zero (0).EXAMPLE 1 For h1= 12 mm, the symbol is 12EXAMPLE 2 For h1= 8 mm, the symbol is 08Figure 23.7

39、Symbol for tool width Reference position (7)3.7.1 Tool holders with rectangular shank cross-sectionFor tool holders with rectangular shank cross-section, see Figure 1.The number symbol for the tool width is the value of the shank width, b, in millimetres. If the resulting symbol has only one digit,

40、it shall be preceded by a zero (0).EXAMPLE 1 For b = 25 mm, the symbol is 25EXAMPLE 2 For b = 8 mm, the symbol is 083.7.2 CartridgesFor cartridges, see Figure 2.Where no indication of shank width is given, a two-letter symbol is indicated instead. The first letter is always C (cartridge) and the sec

41、ond letter identifies the cartridge type. The second letter is specified in the dimensional standards, for example type A in accordance with ISO 5611.3.8 Symbol for tool length Reference position (8)The letter symbol for the tool length shall be chosen from Table 6.For standardized tools where only

42、one length is specified for each tool dimension, the letter symbol for tool length may be replaced by a dash.For standardized cartridges having a tool length, l1, for which no letter symbol is provided in Table 6 (for example l1= 44 mm), the symbol in position (8) shall be a dash.6 ISO 2012 All righ

43、ts reservedBS ISO 5608:2012ISO 5608:2012(E)Table 6Letter symbol Tool length, mm (l1in Figures 1 and 2)A 32B 40C 50D 60E 70F 80G 90H 100J 110K 125L 140M 150N 160P 170Q 180R 200S 250T 300U 350V 400W 450X Special length, to be specifiedY 500 ISO 2012 All rights reserved 7BS ISO 5608:2012ISO 5608:2012(E

44、)3.9 Symbol for indexable insert size Reference position (9)Table 7Insert type Number symbolEquilateral and equiangular (H, O, P, S and T), and equilateral and non-equiangular (C, D, E, M, V and W)The symbol of designation for the insert size is the edge length, disregarding any decimals.EXAMPLEEdge

45、 length: 16,5 mmSymbol of designation: 16Non-equilateral and equiangular (L), and non-equilateral and non-equiangular (A, B and K)The symbol of designation for the insert size is always the length of the major cutting edge or of the longer cutting edge, disregarding any decimals.EXAMPLELength of the

46、 major cutting edge: 19,5 mmSymbol of designation: 19Round (R) The symbol of designation for the insert size is always the diameter, disregarding any decimals.EXAMPLEDiameter: 15,875 mmSymbol of designation: 15NOTE Where the symbol resulting from the retained part of the value of a metric dimension

47、has only one digit, it shall be preceded by a zero (0).EXAMPLEEdge length: 9,525 mmSymbol of designation: 094 Optional symbol: symbol for special tolerances Reference position (10)A qualified tool is a tool with dimensions f1, f2and l1 (see the illustrations in Table 8) having tolerances of 0,08 mm.

48、8 ISO 2012 All rights reservedBS ISO 5608:2012ISO 5608:2012(E)Table 8Letter symbol Qualification of tool IllustrationQ Back and end qualified toolF Front and end qualified toolB Front, back and end qualified tool ISO 2012 All rights reserved 9BS ISO 5608:2012ISO 5608:2012(E)Annex A (informative) Rel

49、ationship between designations in this International Standard and the ISO 13399 seriesFor the relationship between designations in this International Standard and preferred symbols according to the ISO 13399 series, see Table A.1.Table A.1 Relationship between designations in this International Standard and the ISO 13399 seriesSymbol in this International Standard (ISO 5608)Reference in this International Standard (ISO 5608)Property name in the ISO