BS ISO 513-2012 Classification and application of hard cutting materials for metal removal with defined cutting edges Designation of the main groups and groups of application《有规定切割.pdf

《BS ISO 513-2012 Classification and application of hard cutting materials for metal removal with defined cutting edges Designation of the main groups and groups of application《有规定切割.pdf》由会员分享，可在线阅读，更多相关《BS ISO 513-2012 Classification and application of hard cutting materials for metal removal with defined cutting edges Designation of the main groups and groups of application《有规定切割.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS ISO 513:2012Classification and applicationof hard cutting materials formetal removal with definedcutting edges Designation ofthe main groups and groups ofapplicationBS ISO 513

2、:2012 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 513:2012. Itsupersedes BS ISO 513:2004 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee MTE/18, Tools tips and inserts for cutting applications.A list of organiz

3、ations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2012. Published by BSI StandardsLimited 2012ISBN

4、 978 0 580 75877 5ICS 25.100.01Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 December 2012.Amendments issued since publicationDate Text affectedBS ISO 513:201

5、2 ISO 2012Classification and application of hard cutting materials for metal removal with defined cutting edges Designation of the main groups and groups of applicationClassification et application des matriaux durs de coupe pour enlvement de mtal avec artes coupantes dfinies Dfinition des groupes p

6、rincipaux et des groupes dapplicationINTERNATIONAL STANDARDISO513Fourth edition2012-11-01Reference numberISO 513:2012(E)BS ISO 513:2012ISO 513:2012(E)ii ISO 2012 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2012All rights reserved. Unless otherwise specified, no part of this publication may b

7、e reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel. + 41

8、22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 513:2012ISO 513:2012(E) ISO 2012 All rights reserved iiiContents PageForeword ivIntroduction v1 Scope .12 Designation 13 Classification 43.1 Main groups of application . 43.2 Groups of application 4

9、4 Important remarks 4BS ISO 513:2012ISO 513:2012(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each

10、 member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the Internationa

11、l Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.The main task of technical committees is to prepare International Standards. Draft International Standards a

12、dopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.Attention is drawn to the possibility that some of the elements of this document may be the subject of pa

13、tent rights. ISO shall not be held responsible for identifying any or all such patent rights.ISO 513 was prepared by Technical Committee ISO/TC 29, Small tools, Subcommittee SC 9, Tools with cutting edges made of hard cutting materials.This fourth edition cancels and replaces the third edition (ISO

14、513:2004), which has been technically revised.iv ISO 2012 All rights reservedBS ISO 513:2012ISO 513:2012(E)IntroductionThe variety of ways in which different manufacturers produce hard cutting materials with differing characteristics makes it impossible at the time of publication to standardize hard

15、 cutting materials graded in accordance with these characteristics.This International Standard is, therefore, limited to a classification of hard cutting materials based on their application and to a method of designation (colour marking and distinguishing symbols) for the main groups of application

16、 and the groups of application which constitute this classification. ISO 2012 All rights reserved vBS ISO 513:2012BS ISO 513:2012Classification and application of hard cutting materials for metal removal with defined cutting edges Designation of the main groups and groups of application1 ScopeThis I

17、nternational Standard specifies the classification and application of hard cutting materials, including hardmetals, ceramics, diamond and boron nitride, for machining by chip removal, and establishes their application.It is not applicable to other uses (mining and other percussion tools, wire drawin

18、g dies, tools operating by deformation of the metal and comparator contact tips, etc.).2 DesignationThe designation of groups of application for hard cutting materials includes the letter symbols in accordance with Tables 1 to 4, followed by a dash and the designation of the main group of chip remov

19、al and of the group of application, as specified in Clause 4.Table 1 CarbidesIdentification letters Material groupHWUncoated carbide, main content tungsten carbide (WC) with grain size 1 mHFUncoated carbide, main content tungsten carbide (WC) with grain size 1 mHTaUncoated carbide, main content TiC

20、or TiN or bothHCCarbides as above-mentioned, but coatedaThese grades are also called “Cermets”.Table 2 CeramicsIdentification letters Material groupCA Ceramic, main content Al2O3CR Ceramic, main content Al2O3, reinforcedCMMixed ceramic, main content Al2O3plus compo-nents other than oxidesCN Silicon

21、nitride ceramic, main content Si3N4CC Ceramics as above-mentioned, but coatedINTERNATIONAL STANDARD ISO 513:2012(E) ISO 2012 All rights reserved 1BS ISO 513:2012ISO 513:2012(E)Table 3 DiamondIdentification letters Material groupDM Monocrystalline diamondDDPolycrystalline diamond without binderDP Pol

22、ycrystalline diamond with binderTable 4 Boron nitrideIdentification letters Material groupBLCubic crystalline boron nitride with low content of cubic boron nitrideBHCubic crystalline boron nitride with high content of cubic boron nitrideBCCubic crystalline boron nitride as above-men-tioned, but coat

23、edEXAMPLE HW P10HC K20CA K102 ISO 2012 All rights reservedBS ISO 513:2012ISO 513:2012(E)Table 5 Application and classification of hard cutting materialsMain groups of application Group of applicationIdentifica-tion letterIdentifica-tion colourMaterials to be machinedHard cutting materials P blueStee

24、l: all kinds of steel and cast steel except stainless steel with an aus-tenitic structure.P01 P10 P20 P30 P40 P50P05 P15 P25 P35 P45 a bM yellowStainless steel: stainless austenitic and austenitic/ferritic steel and cast steel.M01 M10 M20 M30 M40M05 M15 M25 M35 a bK redCast iron: grey cast iron, cas

25、t iron with sphe-roidal graphite, malleable cast iron.K01 K10 K20 K30 K40K05 K15 K25 K35 a bN greenNon-ferrous metals: aluminium and other non-ferrous metals, non-metallic materials.N01 N10 N20 N30N05 N15 N25 a bS brownSuperalloys and titanium: heat-resistant special alloys based on iron, nickel and

26、 cobalt, titanium and titanium alloys.S01 S10 S20 S30S05 S15 S25 a bH greyHard materials: hardened steel, hardened cast iron materials, chilled cast iron.H01 H10 H20 H30H05 H15 H25 a baIncreasing speed, increasing wear resistance of cutting material (see Table 6). bIncreasing feed, increasing toughn

27、ess of cutting material (see Table 6).Table 6 Area of use chartWear resistance Toughness01 05 10 15 20 25 30 35 40 45 50P M X XK X XN X X X XS X X X XH X X X X ISO 2012 All rights reserved 3BS ISO 513:2012ISO 513:2012(E)3 Classification3.1 Main groups of applicationThere are six main groups of appli

28、cation (see Table 5). They are divided according to the different workpiece materials which are to be machined. They are identified by a capital letter and an identifying colour.3.2 Groups of applicationEach main group of application is divided into application groups. The application groups are des

29、ignated by the letter for the main group and a classification number.The manufacturers of cutting material arrange in proper order their grades into the application group system according to the relative wear resistance and toughness of the grades (see Table 6).Table 6 shows that, according to this

30、International Standard, only “P” grades are thought to operate under conditions sufficiently arduous as to justify wear/toughness classification numbers 45 and 50. “M” and “K” grades may have classification numbers up to 40 and the remaining groups (N, S and H) may be allocated wear/toughness classi

31、fication numbers no greater than 30. Manufacturers may assign any available application code to a specified cutting tool material with qualifying composition.4 Important remarksA group of application is not identical to a cutting material grade. Grades from different manufacturers which are in the s

32、ame application group could be different as far as application range and performance level are concerned. Within an application group, a designation (eg “P01”) is not identical to a cutting material grade. Grades from different manufacturers with the same designation within an application group can

33、be different as far as composition, properties, application range and performance level are concerned. This International Standard, consequently, does not provide data for grade comparison charts.4 ISO 2012 All rights reservedBS ISO 513:2012BS ISO 513:2012ISO 513:2012(E) ISO 2012 All rights reserved

34、ICS 25.100.01Price based on 4 pagesThis page deliberately left blankBSI is the independent national body responsible for preparing British Standards and other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. BSI

35、is incorporated by Royal Charter. British Standards and other standardisation products are published by BSI Standards Limited.British Standards Institution (BSI)raising standards worldwideBSI389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards and PASs are peri

36、odically updated by amendment or revision. Users of British Standards and PASs should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity whi

37、le using British Standards would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside frontcover. Similary for PASs, please notify BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers BSI Subscribing Members an ind

38、ividual updating service called PLUS which ensures that subscribers automatically receive the latest editions of British Standards and PASs.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the

39、 BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, BSI will supply the British Standard implementat

40、ion of the relevant international standard, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: BSI Subscribing Members are ke

41、pt up to date with standards developments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards

42、 and PASs via British Standards Online can be found at information about British Standards is available on the BSI website at www.bsi- the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entit

43、y that own copyright in the information used (such as the international standardisation bodies) has formally licensed such information to BSI for commerical publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval

44、system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Department.Tel: +44 (0)20 8996 7070Email: