BS ISO 43-2016 Aircraft Jacking pads《航空器千斤顶基座》.pdf

《BS ISO 43-2016 Aircraft Jacking pads《航空器千斤顶基座》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 43-2016 Aircraft Jacking pads《航空器千斤顶基座》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BS ISO 43:2016Aircraft Jacking padsBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS ISO 43:2016 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 43:2016.It supersedes BS 2C 12:1980 (dual numbered as ISO 43:1976)which is withdra

2、wn.The UK participation in its preparation was entrusted to TechnicalCommittee ACE/57, Air cargo and ground support equipment. A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions o

3、f a contract. Users are responsible for its correct application. The British Standards Institution 2016. Published by BSI Standards Limited 2016ISBN 978 0 580 92726 3 ICS 49.100 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under

4、 the authority of the Standards Policy and Strategy Committee on 30 November 2016.Amendments/corrigenda issued since publicationDate Text affectedBS ISO 43:2016 ISO 2016Aircraft Jacking padsAronefs Points dappui du vrin de levageINTERNATIONAL STANDARDISO43Second edition2016-11-01Reference numberISO

5、43:2016(E)BS ISO 43:2016ISO 43:2016(E)ii ISO 2016 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2016, Published in SwitzerlandAll rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanic

6、al, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCh. de Blandonnet 8 CP 401CH-1214 Vernier, Geneva, Switzer

7、landTel. +41 22 749 01 11Fax +41 22 749 09 47copyrightiso.orgwww.iso.orgBS ISO 43:2016ISO 43:2016(E)Foreword iv1 Scope . 12 Normative references 13 Terms and definitions . 14 Required characteristics 1 ISO 2016 All rights reserved iiiContents PageBS ISO 43:2016ISO 43:2016(E)ForewordISO (the Internat

8、ional Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has bee

9、n established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical stand

10、ardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordan

11、ce with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of

12、 any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsem

13、ent.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html.ISO

14、 43 was prepared by Technical Committee ISO/TC 20, Aircraft and space vehicles, Subcommittee SC 9, Air cargo and ground equipment.This second edition cancels and replaces the first edition (ISO 43:1976), of which Clause 4 and Figure 1 to Figure 6 has been technically revised to add a seventh size fo

15、r heavier aircraft.iv ISO 2016 All rights reservedBS ISO 43:2016INTERNATIONAL STANDARD ISO 43:2016(E)Aircraft Jacking pads1 ScopeThis document specifies the profiles and dimensions of aircraft jacking pads and the minimum clearance to be provided around them. Aircraft jacking pads, also called adapt

16、ers, can be attached to primary flight structure (PFS) or to axles.2 Normative referencesThere are no normative references in this document.3 Terms and definitionsNo terms and definitions are listed in this document.ISO and IEC maintain terminological databases for use in standardization at the foll

17、owing addresses: IEC Electropedia: available at http:/www.electropedia.org/ ISO Online browsing platform: available at http:/www.iso.org/obp 4 Required characteristicsAircraft jacking pads are to be limited to the seven types specified below, which specify the shape, size and clearances to be provid

18、ed around the pads.They shall meet the shape specified in Figure 1 and the dimensions and clearances specified in Table 1 and Table 2 for the type corresponding to their intended load capacity.Conversion factors: 1 pound force (lbf) = 4,45 Newtons. 1 inch = 25,4 mmKey1 optional taperFigure 1 Jacking

19、 pads adapters categorization ISO 2016 All rights reserved 1BS ISO 43:2016ISO 43:2016(E)Table 1 Jacking pads adapters categorization (pounds inches)a b c r1Type Load LoadAdapter forMinimum clearance spaceMinimum clearance spaceWheel, brake, tire minimum clearanceSpherical radiusmin.pound forcemax.po

20、und force inch inch inch 0.010inchI 0 10000 PFS 3 1.125 N/A 0.5II 10000 112000 PFS 3 to 12 1.187 N/A 0.75III 0 10000 Axle 3 0.750 2.25 0.5IV 10000 150000 Axle 3 to 9 0.875 3.5 0.75V 150000 281100 Axle 9 1.187 4.5 1.25VI 112000 250000 PFS 12 to 13.7 1.375 N/A 1.25VII 250000 359700 PFS 13.7 1.500 N/A

21、1.75Table 2 Jacking pads adapters categorization (kilonewtons mm)a b c r1Type Load LoadAdapter forMinimum clearance spaceMinimum clearance spaceWheel, brake, tire minimum clearanceSpherical radiusmin.kNmax.kN mm mm mm 0,25mmI 0 44,5 PFS 76,2 28,58 N/A 12,70II 44,5 500 PFS 76,2 to 304,8 30,15 N/A 19,

22、05III 0 44,5 Axle 76,2 19,05 57,15 12,70IV 44,5 667 Axle 76,2 to 228,6 22,23 88,9 19,05V 667 1250 Axle 228,6 30,15 114,3 31,75VI 500 1112 PFS 304,8 to 347,98 34,93 N/A 31,75VII 1112 1600 PFS 347,98 38,10 N/A 44,452 ISO 2016 All rights reservedBS ISO 43:2016BS ISO 43:2016ISO 43:2016(E) ISO 2016 All r

23、ights reservedICS 49.100Price based on 2 pagesThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization pro

24、ducts are published by BSI Standards Limited.British Standards Institution (BSI)About usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been

25、 carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Fi

26、nd out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where ha

27、rd copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.Copyright in BSI publicationsAll the content in BSI publications, including British Standards, is the property o

28、f and copyrighted by BSI or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use.Save for the provisions below, you may not transfer, share or dissemin

29、ate any portion of the standard to any other person. You may not adapt, distribute, commercially exploit, or publicly display the standard or any portion thereof in any manner whatsoever without BSIs prior written consent.Storing and using standardsStandards purchased in soft copy format: A British

30、Standard purchased in soft copy format is licensed to a sole named user for personal or internal company use only. The standard may be stored on more than 1 device provided that it is accessible by the sole named user only and that only 1 copy is accessed at any one time. A single paper copy may be

31、printed for personal or internal company use only.Standards purchased in hard copy format: A British Standard purchased in hard copy format is for personal or internal company use only. It may not be further reproduced in any format to create an additional copy. This includes scanning of the documen

32、t.If you need more than 1 copy of the document, or if you wish to share the document on an internal network, you can save money by choosing a subscription product (see Subscriptions).Reproducing extractsFor permission to reproduce content from BSI publications contact the BSI Copyright & Licensing t

33、eam.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from

34、your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an

35、 updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) yo

36、u are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .RevisionsOur British Standards and other publications

37、are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.Useful ContactsCustomer ServicesTel: +44 345 08

38、6 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 345 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Group Headquarters389 Chiswick High Road London W4 4AL UKBSI Back Cover.indd 1 27/01/2016 14:20