BS ISO 2901-2016 ISO metric trapezoidal screw threads Basic and design profiles《ISO公制梯形螺纹 基本和设计轮廓》.pdf

《BS ISO 2901-2016 ISO metric trapezoidal screw threads Basic and design profiles《ISO公制梯形螺纹 基本和设计轮廓》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 2901-2016 ISO metric trapezoidal screw threads Basic and design profiles《ISO公制梯形螺纹 基本和设计轮廓》.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、BS ISO 2901:2016ISO metric trapezoidal screwthreads Basic and designprofilesBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS ISO 2901:2016 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 2901:2016.The UK participation in its p

2、reparation was entrusted to Technical Committee FME/9, Fasteners.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct applicatio

3、n. The British Standards Institution 2016.Published by BSI Standards Limited 2016ISBN 978 0 580 91044 9 ICS 21.040.10 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committe

4、e on 30 September 2016.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dBS ISO 2901:2016 ISO 2016ISO metric trapezoidal screw threads Basic and design profilesFiletages mtriques trapzodaux ISO Profils de base et nominalINTERNATIONAL STANDARDISO2901Third edition2016-09-15Refe

5、rence numberISO 2901:2016(E)BS ISO 2901:2016ISO 2901:2016(E)ii ISO 2016 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2016, Published in SwitzerlandAll rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means,

6、electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCh. de Blandonnet 8 CP 401CH-1214 Ve

7、rnier, Geneva, SwitzerlandTel. +41 22 749 01 11Fax +41 22 749 09 47copyrightiso.orgwww.iso.orgBS ISO 2901:2016ISO 2901:2016(E)Foreword iv1 Scope . 12 Normative references 13 Terms and definitions . 14 Symbols 15 Basic profile . 26 Design profile . 4Bibliography 6 ISO 2016 All rights reserved iiiCont

8、ents PageBS ISO 2901:2016ISO 2901:2016(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member bo

9、dy interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrot

10、echnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of IS

11、O documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held res

12、ponsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information give

13、n for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Tr

14、ade (TBT) see the following URL: www.iso.org/iso/foreword.html.The committee responsible for this document is ISO/TC 1, Screw threads.This third edition cancels and replaces the second edition (ISO 2901:1993), which has been technically revised. The following changes have been made: the phrase “maxi

15、mum material profiles” has been replaced by “design profiles”; the reference ISO 2903 has been replaced by ISO 5408; the symbols have been updated; the definition of basic profile has been deleted; Figure 2 has been revised and Figure 3 has been deleted.iv ISO 2016 All rights reservedBS ISO 2901:201

16、6INTERNATIONAL STANDARD ISO 2901:2016(E)ISO metric trapezoidal screw threads Basic and design profiles1 ScopeThis document specifies the basic and design profiles of ISO metric trapezoidal screw threads.This document is chiefly applicable to traversing threads for traversing motion on machines, tool

17、s, etc. It can also be used for fastening threads.2 Normative referencesThere are no normative references in this document.3 Terms and definitionsFor the purposes of this document, the terms and definitions given in ISO 5408 apply.ISO and IEC maintain terminological databases for use in standardizat

18、ion at the following addresses: IEC Electropedia: available at http:/www.electropedia.org/ ISO Online browsing platform: available at http:/www.iso.org/obp4 SymbolsFor the purposes of this document, the following symbols apply.D major diameter of internal thread on basic profileD4major diameter of i

19、nternal thread on design profiled major diameter of external thread (nominal diameter)D2pitch diameter of internal threadd2pitch diameter of external threadD1minor diameter of internal threadd1minor diameter of external thread on basic profiled3minor diameter of external thread on design profileP pi

20、tchH fundamental triangle heightH2thread height on basic profileH0thread overlap on design profileH4thread height of internal thread on design profile ISO 2016 All rights reserved 1BS ISO 2901:2016ISO 2901:2016(E)h3thread height of external thread on design profileacclearances at major and minor dia

21、meters on design profilew width of flat crest or root on basic profileR1radius on crest corners of external thread on design profileR2radius on root corners of internal and external threads on design profile5 Basic profileThe basic profile is shown as a thick line in Figure 1. It is common to intern

22、al and external threads.The dimensions of the basic profile are given in Table 1.H = P/(2 tan15) = 1,866 025 404 PH2= 0,5 Pw = (H H2) P/(2H) = 0,366 PKey1 axis of screw threadFigure 1 Basic profile2 ISO 2016 All rights reservedBS ISO 2901:2016ISO 2901:2016(E)Table 1 Basic profile dimensionsDimension

23、s in millimetresPitchPH H/2 H2w1,5 2,799 1,400 0,75 0,5492 3,732 1,866 1 0,7323 5,598 2,799 1,5 1,0984 7,46 4 3,732 2 1,4645 9,330 4,665 2,5 1,8306 11,196 5,598 3 2,1967 13,062 6,531 3,5 2,5628 14,928 7,46 4 4 2,9289 16,794 8,397 4,5 3,29410 18,660 9,330 5 3,66012 22,392 11,196 6 4,39214 26,124 13,0

24、62 7 5,12416 29,856 14,928 8 5,85618 33,588 16,794 9 6,58820 37, 320 18,660 10 7, 32022 41,052 20,526 11 8,05224 44,784 22,392 12 8,78428 52,248 26,124 14 10,24832 59,712 29,856 16 11,71236 67,176 33,588 18 13,17640 74,640 37, 320 20 14,64044 82,104 41,052 22 16,104 ISO 2016 All rights reserved 3BS

25、ISO 2901:2016ISO 2901:2016(E)6 Design profileThe two design profiles are shown as a thick line in Figure 2. They are different between internal and external threads. The limit deviations are applied to the design profiles.The dimensions of the design profiles are given in Table 2.H0= H2= 0,5Ph3= H4=

26、 H0+ ac= 0,5P + acD1= d 2H0= d Pd2= D2= d H0= d 0,5Pd3= d 2h3= d 2(0,5P + ac)D4= d + 2acR1 max= 0,5acR2 max= acIn the case of manufacture by rolling, the profile at the minor diameter can be modified in order to obtain a larger rounding on the root of the external thread. The minor diameter d3of the

27、 external thread may in this case be reduced by 0,15P.If the modification of the profile becomes necessary, due to the particular methods of manufacture, it shall be agreed upon between the customer and the manufacturer.Key1 internal thread2 external threadFigure 2 Design profiles4 ISO 2016 All righ

28、ts reservedBS ISO 2901:2016ISO 2901:2016(E)Table 2 Design profile dimensionsDimensions in millimetresPitchPacH4= h3R1 maxR2 max1,5 0,15 0,9 0,075 0,152 0,25 1,25 0,125 0,253 0,25 1,75 0,125 0,254 0,25 2,25 0,125 0,255 0,25 2,75 0,125 0,256 0,5 3,5 0,25 0,57 0,5 4 0,25 0,58 0,5 4,5 0,25 0,59 0,5 5 0,

29、25 0,510 0,5 5,5 0,25 0,512 0,5 6,5 0,25 0,514 1 8 0,5 116 1 9 0,5 118 1 10 0,5 120 1 11 0,5 122 1 12 0,5 124 1 13 0,5 128 1 15 0,5 132 1 17 0,5 136 1 19 0,5 140 1 21 0,5 144 1 23 0,5 1 ISO 2016 All rights reserved 5BS ISO 2901:2016ISO 2901:2016(E)Bibliography1 ISO 5408, Screw threads Vocabulary6 IS

30、O 2016 All rights reservedBS ISO 2901:2016BS ISO 2901:2016ISO 2901:2016(E) ISO 2016 All rights reservedICS 21.040.10Price based on 6 pagesThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and se

31、rvices.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)About usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience an

32、d expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information o

33、n standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, includin

34、g British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.Copyright in BSI pub

35、licationsAll the content in BSI publications, including British Standards, is the property of and copyrighted by BSI or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercia

36、l publication and use.Save for the provisions below, you may not transfer, share or disseminate any portion of the standard to any other person. You may not adapt, distribute, commercially exploit, or publicly display the standard or any portion thereof in any manner whatsoever without BSIs prior wr

37、itten consent.Storing and using standardsStandards purchased in soft copy format: A British Standard purchased in soft copy format is licensed to a sole named user for personal or internal company use only. The standard may be stored on more than 1 device provided that it is accessible by the sole n

38、amed user only and that only 1 copy is accessed at any one time. A single paper copy may be printed for personal or internal company use only.Standards purchased in hard copy format: A British Standard purchased in hard copy format is for personal or internal company use only. It may not be further

39、reproduced in any format to create an additional copy. This includes scanning of the document.If you need more than 1 copy of the document, or if you wish to share the document on an internal network, you can save money by choosing a subscription product (see Subscriptions).Reproducing extractsFor p

40、ermission to reproduce content from BSI publications contact the BSI Copyright & Licensing team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have

41、instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, b

42、oth in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing

43、 Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is cur

44、rent. For further information, email .RevisionsOur British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI pu

45、blication please inform the Knowledge Centre.Useful ContactsCustomer ServicesTel: +44 345 086 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 345 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Group Headquarters389 Chiswick High Road London W4 4AL UKBSI Back Cover.indd 1 27/01/2016 14:20