BS ISO 27668-2-2009 Gel ink ball pens and refills - Documentary use (DOC)《中性圆珠笔和笔芯 文件使用(DOC)》.pdf

《BS ISO 27668-2-2009 Gel ink ball pens and refills - Documentary use (DOC)《中性圆珠笔和笔芯 文件使用(DOC)》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 27668-2-2009 Gel ink ball pens and refills - Documentary use (DOC)《中性圆珠笔和笔芯 文件使用(DOC)》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BS ISO27668-2:2009ICS 01.100.40; 97.180NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDGel ink ball pens andrefillsPart 2: Documentary use (DOC)This British Standardwas published under theauthority of the StandardsPolicy and StrategyCommittee on 31 May 2009 BSI

2、2009ISBN 978 0 580 61705 8Amendments/corrigenda issued since publicationDate CommentsBS ISO 27668-2:2009National forewordThis British Standard is the UK implementation of ISO 27668-2:2009.The UK participation in its preparation was entrusted to TechnicalCommittee TDW/4, Technical product realization

3、 (TPR).A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunityf

4、rom legal obligations.BS ISO 27668-2:2009Reference numberISO 27668-2:2009(E)ISO 2009INTERNATIONAL STANDARD ISO27668-2First edition2009-02-01Gel ink ball pens and refills Part 2: Documentary use (DOC) Stylos bille encre gel et recharges Partie 2: Utilisation documentaire (DOC) BS ISO 27668-2:2009ISO

5、27668-2:2009(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloa

6、ding this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the Ge

7、neral Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address giv

8、en below. COPYRIGHT PROTECTED DOCUMENT ISO 2009 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the

9、 address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2009 All rights reservedBS ISO 27668-2:2009ISO 27668-2:2009(

10、E) ISO 2009 All rights reserved iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body in

11、terested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechni

12、cal Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the

13、 technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. ISO 27668-2 was prepared by Technical Committee ISO/TC 10, Technical product documentation. ISO 27668 consists of the

14、 following parts, under the general title Gel ink ball pens and refills: Part 1: General use Part 2: Documentary use (DOC) BS ISO 27668-2:2009ISO 27668-2:2009(E) iv ISO 2009 All rights reservedIntroduction This part of ISO 27668 is applicable to gel ink ball pens for documentary use. Part 1 of ISO 2

15、7668 is applicable to gel ink ball pens for general use. For documentary use, some requirements, in addition to those for general use, are necessary a) to assure the legibility of lettering, and b) for the handling and storage of documents over long periods of time (these requirements are often disc

16、ussed with the archivist). An example of documentary use is the preparation of documents that are required as evidence. Furthermore, pens which meet the requirements for documentary use produce lines which are more resistant to modification (e.g. attempts to falsify a document) than those for genera

17、l use. The International Organization for Standardization (ISO) draws attention to the fact that it is claimed that compliance with this document may involve the use of a patent concerning aqueous gel ink-filled ballpoint pens. The holder of this patent right has assured ISO that he is willing to ne

18、gotiate licences under reasonable and non-discriminatory terms and conditions with applicants throughout the world. In this respect, the statement of the holder of this patent right is registered with ISO. Information may be obtained from: Mitsubishi Pencil Company Limited Patent Administration Depa

19、rtment, 5.23-37, Higashi-ohi JP-Shinagawa, Tokyo 140-8537 Japan oomorihmpuni.co.jp Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights other than those identified above. ISO shall not be held responsible for identifying any or all such

20、 patent rights. BS ISO 27668-2:2009INTERNATIONAL STANDARD ISO 27668-2:2009(E) ISO 2009 All rights reserved 1Gel ink ball pens and refills Part 2: Documentary use (DOC) 1 Scope This part of ISO 27668 establishes minimum quality requirements for gel ink ball pens (refillable or non-refillable) and ref

21、ills for documentary use. Basic requirements for gel ink ball pens for general use are given in ISO 27668-1. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references,

22、 the latest edition of the referenced document (including any amendments) applies. ISO 105-A02, Textiles Tests for colour fastness Part A02: Grey scale for assessing change in colour ISO 105-B02, Textiles Tests for colour fastness Part B02: Colour fastness to artificial light: Xenon arc fading lamp

23、test ISO 27668-1:2009, Gel ink ball pens and refills Part 1: General use 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 27668-1 apply. 4 Requirements 4.1 General requirements See the general requirements given in ISO 27668-1:2009 (4.1 to 4.3.4, 4.3.

24、7 and 4.3.8). 4.2 Erasure resistance The surface of the testing paper shall show clear evidence of damage before the line is rendered invisible when tested as specified in 6.2.1. 4.3 Ethanol resistance The line shall remain visible when tested as specified in 6.2.2. BS ISO 27668-2:2009ISO 27668-2:20

25、09(E) 2 ISO 2009 All rights reserved4.4 Hydrochloric acid resistance The line shall remain visible when tested as specified in 6.2.3. 4.5 Ammonium hydroxide resistance The line shall remain visible when tested as specified in 6.2.4. 4.6 Bleaching resistance The line shall remain visible when tested

26、as specified in 6.2.5. 4.7 Water resistance The line shall remain visible when tested as specified in 6.2.6. 4.8 Light resistance The line shall remain visible when tested as specified in 6.2.7. 5 Test equipment, accessories and solutions 5.1 Test equipment and accessories See ISO 27668-1. 5.2 Test

27、solutions 5.2.1 Ethanol solution, 50 % aqueous solution (volume fraction). 5.2.2 Hydrochloric acid solution, 10 % aqueous solution (mass fraction). 5.2.3 Ammonium hydroxide solution, 10 % aqueous solution (mass fraction). 5.2.4 Bleaching solution, 3 % freshly made aqueous solution of chloramin T1)(m

28、ass fraction). 6 Testing 6.1 General test 6.1.1 Sampling See ISO 27668-1:2009, 6.1. 6.1.2 Climatic conditions See ISO 27668-1:2009, 6.2. 6.1.3 General test procedure See ISO 27668-1:2009, 6.3. 1) Standard designation: N-chloro-p-toluene sulfonamide sodium salt. IUPAC designation: N-chloro-4-metyl-be

29、nzene sulfonamide sodium salt. BS ISO 27668-2:2009ISO 27668-2:2009(E) ISO 2009 All rights reserved 36.2 Additional tests 6.2.1 Erasure resistance test Keep a fresh machine-written test piece approximately 5 cm long from the sheet provided in 6.1.3 under the climatic conditions specified in 6.1.2 for

30、 10 min (to allow to dry), and then erase a portion of line with the eraser specified in ISO 27668-1:2009, 5.3. Examine the surface of the erased section of the paper for compliance with 4.2. 6.2.2 Ethanol resistance test Keep a machine-written test piece approximately 5 cm long from the sheet provi

31、ded in 6.1.3 under the climatic conditions specified in 6.1.2 for 1 h (to allow to dry), and then immerse in the ethanol solution specified in 5.2.1 for 10 min. Remove and allow to air dry. Examine the written line of the test piece for compliance with 4.3. 6.2.3 Hydrochloric acid resistance test Ke

32、ep a machine-written test piece approximately 5 cm long from the sheet provided in 6.1.3 under the climatic conditions specified in 6.1.2 for 1 h (to allow to dry), then immerse in the hydrochloric acid solution specified in 5.2.2 for 24 h. Remove and immerse in distilled water or de-ionized water f

33、or 10 min and allow to air dry. Examine the written line of the test piece for compliance with 4.4. 6.2.4 Ammonium hydroxide resistance test Keep a machine-written test piece approximately 5 cm long from the sheet provided in 6.1.3 under the climatic conditions specified in 6.1.2 for 1 h (to allow t

34、o dry), then immerse in the ammonium hydroxide solution specified in 5.2.3 for 24 h. Remove and immerse in distilled water or de-ionized water for 10 min and allow to air dry. Examine the written line of the test piece for compliance with 4.5. 6.2.5 Bleaching resistance test Keep a machine-written t

35、est piece approximately 5 cm long from the sheet provided in 6.1.3 under the climatic conditions specified in 6.1.2 for 10 min (to allow to dry), then immerse in the bleaching solution specified in 5.2.4 for 5 min. Remove and immerse in distilled water or de-ionized water for 10 min and allow to air

36、 dry. Examine the written line of the test piece for compliance with 4.6. 6.2.6 Water resistance test Keep a machine-written test piece approximately 5 cm long from the sheet provided in 6.1.3 under the climatic conditions specified in 6.1.2 for 2 h (to allow to dry), then immerse in distilled water

37、 or de-ionized water for 24 h. Remove and allow to air dry. Examine the written line of the test piece for compliance with 4.7. 6.2.7 Light resistance test Expose a machine-written test piece approximately 5 cm long from the sheet provided in 6.1.3 to the light source of the apparatus specified in I

38、SO 27668-1, 5.5, together with the blue wool references specified in ISO 105-B02 until the contrast between the unexposed and the exposed blue wool reference 5 becomes equal to grey scale grade 4 specified in ISO 105-A02. Examine the written line of the test piece for compliance with 4.8. BS ISO 276

39、68-2:2009ISO 27668-2:2009(E) 4 ISO 2009 All rights reserved7 Designation and marking 7.1 Designation The designation of a gel ink ball pen or refill shall comprise, in the given order, the following elements: a) the description block (e.g. “gel ink ball pen” or “gel ink ball refill”); b) the number

40、of this part of ISO 27668 (i.e. ISO 27668-2); c) the type classification code for refills (see 4.2 of ISO 27668-1:2009); d) the tip classification code (UF, EF, F, M or B; see Table 1 of ISO 27668-1:2009); and e) an additional indicator for documentary use (DOC). EXAMPLE 1 A disposable gel ink ball

41、pen complying with the requirements of this part of ISO 27668, with medium sized tip (M), shall be designated as follows: Gel ink ball pen ISO 27668-2 M DOC EXAMPLE 2 A gel ink ball refill complying with the requirements of this part of ISO 27668, type B, with a broad sized tip (B), shall be designa

42、ted as follows: Gel ink ball refill ISO 27668-2 B B DOC 7.2 Marking For identification, disposable gel ink ball pens or refills shall be marked as follows: a) the name of the manufacturer, supplier or trademark; b) the designation in accordance with 7.1 except 7.1 a), which is optional; and c) the d

43、ate of manufacture (year/month, in full or coded) or the batch number. 8 Test report The test report shall include the following information: a) reference to this part of ISO 27668; b) the date and place of test; c) precise identification of the samples (see 7.2); d) identification of the following

44、variable or optional requirements: 1) test atmosphere (see 6.2 of ISO 27668-1:2009), 2) writing angle and writing pitch (see 5.1 of ISO 27668-1:2009), 3) reproducibility apparatus (see 5.4 of ISO 27668-1:2009), and 4) light test apparatus (see 5.5 of ISO 27668-1:2009); e) the results in accordance w

45、ith this part of ISO 27668, as well as a confirmation of permitted application for documentary use; f) any deviations from the specified procedures (see Clauses 5 and 6); and g) the identification and signature of the tester. BS ISO 27668-2:2009BS ISO 27668-2:2009ISO 27668-2:2009(E) ICS 01.100.40 Pr

46、ice based on 4 pages ISO 2009 All rights reserved BS ISO 27668-2:2009This page has been intentionally left blank BS ISO27668-2:2009BSI GroupHeadquarters 389Chiswick High Road,London, W4 4AL, UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 - British Standards InstitutionBSI is the independent national b

47、ody responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at theinternational level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest a

48、mendments oreditions.It is the constant aim of BSI to improve the quality of our products and services.We would be grateful if anyone finding an inaccuracy or ambiguity while usingthis British Standard would inform the Secretary of the technical committeeresponsible, the identity of which can be fou

49、nd on the inside front cover. Tel:+44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should beaddressed to Custo