BS ISO 27145-2-2012 Road vehicles Implementation of World-Wide Harmonized On-Board Diagnostics (WWH-OBD) communication requirements Common data dictionary《道路车辆 全球统一的车载诊断系统 (WWH-OBD.pdf

《BS ISO 27145-2-2012 Road vehicles Implementation of World-Wide Harmonized On-Board Diagnostics (WWH-OBD) communication requirements Common data dictionary《道路车辆 全球统一的车载诊断系统 (WWH-OBD.pdf》由会员分享，可在线阅读，更多相关《BS ISO 27145-2-2012 Road vehicles Implementation of World-Wide Harmonized On-Board Diagnostics (WWH-OBD) communication requirements Common data dictionary《道路车辆 全球统一的车载诊断系统 (WWH-OBD.pdf（48页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS ISO 27145-2:2012Road vehicles Implementation of W o r l d - W i d e H a r m o n i z e d On-Board Diagnostics (WWH-OBD) communication requirementsPart 2: Common data dictionary

2、BS ISO 27145-2:2012 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 27145-2:2012. It supersedes DD ISO/PAS 27145-2:2006, which is withdrawn.The UK participation in its preparation was entrusted to T e c h n i c a l C o m m i t t e e A U E / 1 6 , E l e c t r i

3、c a l a n d e l e c t r o n i c e q u i p m e n t .A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British

4、 Standards Institution 2012Published by BSI Standards Limited 2012ISBN 978 0 580 68189 9 ICS 43.040.10; 43.180 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31

5、 August 2012.Amendments issued since publicationDate T e x t a f f e c t e dBS ISO 27145-2:2012Reference numberISO 27145-2:2012(E)ISO 2012INTERNATIONAL STANDARD ISO27145-2First edition2012-08-15Road vehicles Implementation of World-Wide Harmonized On-Board Diagnostics (WWH-OBD) communication require

6、ments Part 2: Common data dictionary Vhicules routiers Mise en application des exigences de communication pour le diagnostic embarqu harmonis lchelle mondiale (WWH-OBD) Partie 2: Dictionnaire de donnes communes BS ISO 27145-2:2012ISO 27145-2:2012(E) COPYRIGHT PROTECTED DOCUMENT ISO 2012 All rights r

7、eserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the req

8、uester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2012 All rights reservedBS ISO 27145-2:2012ISO 27145-2:2012(E) ISO 2012 All rights reserved iiiContents Page Foreword iv

9、 0 Introduction v 1 Scope 1 2 Normative references 2 3 Terms, definitions and abbreviated terms 2 3.1 Terms and definitions . 2 3.2 Abbreviated terms . 4 4 Conventions . 5 5 Document overview . 5 6 Common data dictionary requirements 7 6.1 Data range layout 7 6.2 Diagnostic trouble code (DTC) range

10、layout 7 7 Data identifier and routine identifier data record requirements . 8 7.1 Data identifier and routine identifier definitions 8 7.2 DID and RID data record definition 8 8 Diagnostic trouble code definition 14 8.1 Overview . 14 8.2 SAE J2012-DA and SAE J1939-73 DTCs . 15 9 Presentation layer

11、requirements . 18 Annex A (normative) DID (PID, MID, ITID) and RID supported definition 19 Annex B (normative) WWH-OBD server/ECU supported mandatory DID . 22 Annex C (informative) GTR WWH-OBD emissions system parameters 23 Annex D (normative) GTR WWH-OBD DTCExtendedDataRecord content . 30 Annex E (

12、informative) Definition guidelines for new DID (PID, MID, ITID) assignments . 31 Bibliography 34 BS ISO 27145-2:2012ISO 27145-2:2012(E) iv ISO 2012 All rights reservedForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member

13、bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental

14、and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directive

15、s, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies c

16、asting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 27145-2 was prepared by Technical Committee ISO/TC 22, Road vehicles, Subcommittee

17、 SC 3, Electrical and electronic equipment. This first edition of ISO 27145-2 cancels and replaces ISO/PAS 27145-2:2006, which has been technically revised. ISO 27145 consists of the following parts, under the general title Road vehicles Implementation of World-Wide Harmonized On-Board Diagnostics (

18、WWH-OBD) communication requirements: Part 1: General information and use case definition Part 2: Common data dictionary Part 3: Common message dictionary Part 4: Connection between vehicle and test equipment The following parts are under preparation: Part 6: External test equipment BS ISO 27145-2:20

19、12ISO 27145-2:2012(E) ISO 2012 All rights reserved v0 Introduction 0.1 Overview The ISO 27145 series includes the communication between the vehicles on-board diagnostics (OBD) systems and external test equipment within the scope of the World-Wide Harmonized On-Board Diagnostics Global Technical Regu

20、lations (WWH-OBD GTR). It has been established in order to apply the unified diagnostic services (specified in ISO 14229-1) to WWH-OBD systems. The ISO 27145 series includes the communication between the vehicles WWH-OBD systems and external (off-board) “generic“ test equipment within the scope of t

21、he country-specific regulatory requirements. To achieve this, it is based on the Open Systems Interconnection (OSI) Basic Reference Model in ISO/IEC 7498-1 and ISO/IEC 10731, which structures communication systems into seven layers. Where mapped on this model, the services specified by ISO 27145 are

22、 divided into diagnostic services (layer 7), specified in ISO 27145-3 with reference to ISO 14229-1, presentation layer (layer 6), specified in this part of ISO 27145 with reference to SAE J1930-DA, SAE J1939 Companion Spreadsheet (SPNs), SAE J1939-73:2010, Appendix A (FMIs), SAE J1979-DA and SAE J2

23、012-DA, session layer services (layer 5), specified in ISO 14229-2, transport layer services (layer 4), specified in ISO 27145-4 with reference to ISO 13400-2, ISO 15765-2 and ISO 15765-4, network layer services (layer 3), specified in ISO 27145-4 with reference to ISO 15765-4, ISO 15765-2 and ISO 1

24、3400-2, data link layer (layer 2), specified in ISO 27145-4 with reference to ISO 11898-1, ISO 11898-2, ISO 15765-4, ISO 13400-3 and IEEE 802.3, and physical layer (layer 1), specified in ISO 27145-4 with reference to ISO 11898-1, ISO 11898-2, ISO 15765-4, ISO 13400-3 and IEEE 802.3, in accordance w

25、ith Table 1. Table 1 WWH-OBD specification reference applicable to the OSI layers Applicability OSI seven layer WWH-OBD reference Seven layers according to ISO/IEC 7498-1 and ISO/IEC 10731 Application (layer 7) ISO 14229-1, ISO 27145-3 Presentation (layer 6) This part of ISO 27145, SAE J1930-DA, SAE

26、 J1939 Companion Spreadsheet (SPNs), SAE J1939-73:2010, Appendix A (FMIs), SAE J1979-DA, SAE J2012-DA Session (layer 5) ISO 14229-2 Transport (layer 4) ISO 15765-2 DoCAN, ISO 15765-4 DoCAN ISO 27145-4 ISO 13400-2 DoIP TCP and IP Network (layer 3) Data link (layer 2) ISO 11898-1 CAN DLL, ISO 11898-2

27、CAN HS, ISO 15765-4 DoCAN ISO 13400-3 DoIP, IEEE 802.3 Physical (layer 1) BS ISO 27145-2:2012ISO 27145-2:2012(E) vi ISO 2012 All rights reserved0.2 SAE document reference concept ISO 27145 makes reference to several SAE documents which contain the relevant terms, data and diagnostic trouble code (DT

28、C) definitions. ISO 27145-2 defines a common data dictionary for the ISO 27145 series, according to the definitions in the following documents (see Figure 1): SAE J1930-DA: this digital annex contains all standardized naming objects, terms and abbreviations. SAE J1939 Companion Spreadsheet and SAE J

29、1939-73: SAE J1939 Companion Spreadsheet indexes names for suspect parameter numbers (SPNs), which provide an alternative presentation format for SAE J2012-DA DTCs. SPNs are combined with failure mode indicators (FMIs) to form the full alternative presentation. FMIs are described in SAE J1939-73:201

30、0, Appendix A. NOTE The SAE J1939 Companion Spreadsheet is a document which supplements the SAE J1939 family of standards and contains SPNs and PGNs. SAE J1979-DA: this digital annex contains all standardized data items such as data identifiers (DIDs), test identifiers (TIDs), monitor identifiers (M

31、IDs) and info type identifiers (ITIDs). SAE J2012-DA: this digital annex contains all standardized data items such as DTC definitions and failure type byte (FTB) definitions. ISO 27145-2WWH-OBDcommon data dictionary SAE J1979-DAdigital annex of E/Ediagnostic test modesSAE J2012-DA digital annex of d

32、iagnostic trouble code definitionsSAE J1930-DAdigital annex of electrical /electronic systems diagnostic terms, definitions, abbreviations and acronymsSAE J1939 Companion SpreadsheetSAE J1939-73:2010Appendix A21Key 1 SAE digital annexes: data definitions 2 SAE J1939 series of documents: DTC definiti

33、ons Figure 1 SAE digital annex document reference 0.3 SAE digital annex revision procedure New regulatory requirements drive new in-vehicle technology to lower emissions, improve safety, etc. It is important to standardize new technology-related OBD monitor data and diagnostic trouble codes in order

34、 to support the external (off-board) “generic“ test equipment. All relevant information is proposed by the automotive industry represented by members of the appropriate SAE task force. This part of ISO 27145 references a “Change request form“ for use with new data items to be defined by the SAE task

35、 force for standardization. It is intended that the standardized data items be defined in SAE J1930-DA, SAE J1979-DA, SAE J2012-DA and SAE J1939. It is intended that the documents be published on the SAE store website once the information has been balloted and approved. BS ISO 27145-2:2012ISO 27145-

36、2:2012(E) ISO 2012 All rights reserved viiThe revision request forms and instructions for updating the registers to ISO 27145 can be obtained on the following data registration websites. For SAE J1930-DA: http:/www.sae.org/servlets/works/committeeHome.do?comtID=TEVDS7 The column entitled “Resources“

37、 shows a document with the title: J1930-DA_Revision_Request_Form.doc. Double click on the name to download the document with the filename: “SAE_J1930-DA_Revision_Request_Form.doc“. For SAE J1939: http:/www.sae.org/ Search “J1939 Request“, select “J1939 Request Processing Group“, and select “ J1939 R

38、equest Processing Form and Guidelines“. For SAE J1979-DA: http:/www.sae.org/servlets/works/committeeHome.do?comtID=TEVDS14 The column entitled “Resources“ shows a document with the title: J1979-DA_Revision_Request_Form.doc. Double click on the name to download the document with the filename: “SAE_J1

39、979-DA_Revision_Request_Form.doc“. For SAE J2012-DA: http:/www.sae.org/servlets/works/committeeHome.do?comtID=TEVDS9 The column entitled “Resources“ shows a document with the title: J2012-DA_Revision_Request_Form.doc. Double click on the name to download the document with the filename: “SAE_J2012-DA

40、_Revision_Request_Form.doc“. It is intended that the revision request form be filled out with the request. It is intended that e-mails with completed revision request forms as attachments be sent to: E-mail: saej1930sae.org E-mail: saej1979sae.org E-mail: saej2012sae.org E-mail: saej1939sae.org BS I

41、SO 27145-2:2012BS ISO 27145-2:2012INTERNATIONAL STANDARD ISO 27145-2:2012(E) ISO 2012 All rights reserved 1Road vehicles Implementation of World-Wide Harmonized On-Board Diagnostics (WWH-OBD) communication requirements Part 2: Common data dictionary 1 Scope This part of ISO 27145 defines all regulat

42、ory data elements of the ISO 27145 series. The data elements are used to provide the external test equipment with the diagnostic status of the vehicle on-board diagnostics (VOBD) system in the vehicle. All data elements are communicated with the unified diagnostic services as defined in ISO 27145-3.

43、 The data elements are diagnostic trouble codes (DTCs), data identifiers (DIDs) and routine identifiers (RIDs). The mapping from parameter identifiers (PIDs), monitor identifiers (MIDs) and info type identifiers (ITIDs) is described in this part of ISO 27145. If new legislated WWH-OBD GTR modules ar

44、e established, it is intended that ISO 27145 be applicable with possible extensions, which can be included in this part of ISO 27145, can be specified as enhancements of the SAE Digital Annexes or can even be part of other referenced documents which are intended to include the applicable data defini

45、tions. ISO 27145 is intended to become the single communication standard for access to OBD-related information (VOBD). To allow for a smooth migration from the existing communication standards to this future world-wide communication standard, the communication concept as specified in ISO 27145-4 is

46、based on two different data links: ISO 15765-4 and ISO 13400 (all parts). In view of the usage of standard network layer protocols, future extensions to optional physical layers (e.g. wireless) are possible. NOTE It is expected to extend ISO 27145-4 as necessary upon introduction of additional commu

47、nication media. ISO 27145-4 is the entry point to establish communication with the vehicle. Based on the results of the initialization, the external test equipment determines which protocol and diagnostic services are supported by the vehicles emissions-related system, i.e. legislated OBD: ISO 15031

48、 series, and legislated WWH-OBD: ISO 27145. Vehicles according to ISO 27145 provide VOBD system support as envisioned for WWH-OBD by Global Technical Regulation (GTR) No. 5. IMPORTANT Use cases deriving from country-specific implementation of GTR No. 5 into local legislation are not included in this

49、 part of ISO 27145. BS ISO 27145-2:2012ISO 27145-2:2012(E) 2 ISO 2012 All rights reserved2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 14229-1:1 ), Road vehicles Unified diagnostic services (UDS) Part 1: Specification and requireme