BS ISO 2558-2010 Textile glass chopped-strand mats for reinforcement of plastics Determination of time of dissolution of the binder in styrene《增强塑料用玻璃纤维短切原丝毡 粘合剂在苯乙烯中溶解时间的测定》.pdf

《BS ISO 2558-2010 Textile glass chopped-strand mats for reinforcement of plastics Determination of time of dissolution of the binder in styrene《增强塑料用玻璃纤维短切原丝毡 粘合剂在苯乙烯中溶解时间的测定》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 2558-2010 Textile glass chopped-strand mats for reinforcement of plastics Determination of time of dissolution of the binder in styrene《增强塑料用玻璃纤维短切原丝毡 粘合剂在苯乙烯中溶解时间的测定》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS ISO 2558:2010Textile glass chopped-strandmats for reinforcement ofplastics Determination oftime of dissolution of thebinder in styreneBS ISO 2558:2010 BRITISH STANDARDNational

2、 forewordThis British Standard is the UK implementation of ISO 2558:2010.The UK participation in its preparation was entrusted to TechnicalCommittee PRI/42, Fibre reinforced thermosetting plastics andprepregs.A list of organizations represented on this committee can beobtained on request to its secr

3、etary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. BSI 2010ISBN 978 0 580 69442 4ICS 59.100.10Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was publish

4、ed under the authority of theStandards Policy and Strategy Committee on 31 December 2010.Amendments issued since publicationDate Text affectedBS ISO 2558:2010Reference numberISO 2558:2010(E)ISO 2010INTERNATIONAL STANDARD ISO2558Second edition2010-10-01Textile glass chopped-strand mats for reinforcem

5、ent of plastics Determination of time of dissolution of the binder in styrene Mats de verre textile fils coups pour renforcement des matires plastiques Dtermination du temps de dissolution du liant dans le styrne BS ISO 2558:2010ISO 2558:2010(E) PDF disclaimer This PDF file may contain embedded type

6、faces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infri

7、nging Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were opti

8、mized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2010 All rights reserved. U

9、nless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. IS

10、O copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2010 All rights reservedBS ISO 2558:2010ISO 2558:2010(E) ISO 2010 All rights reserved iiiForeword ISO (the International Organizat

11、ion for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established h

12、as the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Int

13、ernational Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Public

14、ation as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent ri

15、ghts. ISO 2558 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 13, Composites and reinforcement fibres. This second edition cancels and replaces the first edition (ISO 2558:1974), of which it constitutes a minor revision (in 6.1, the minimum distance from the edge of the mat

16、 at which test specimens may be cut out has been increased to 30 mm and, in 6.2, a requirement has been added to condition not only the specimens but also the styrene before the test). BS ISO 2558:2010BS ISO 2558:2010INTERNATIONAL STANDARD ISO 2558:2010(E) ISO 2010 All rights reserved 1Textile glass

17、 chopped-strand mats for reinforcement of plastics Determination of time of dissolution of the binder in styrene 1 Scope This International Standard specifies a method of determining the time taken for a tensile load to break the bond between the strands of a textile glass chopped-strand mat, used f

18、or the reinforcement of plastics, which is immersed in styrene. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced documen

19、t (including any amendments) applies. ISO 291, Plastics Standard atmospheres for conditioning and testing 3 Principle A test specimen is suspended vertically in pure styrene and a tensile load applied by means of a weight attached to the Iower end of the specimen. The time taken for the weight to fa

20、ll a specified distance is recorded. NOTE It is possible to distinguish better between mats having binders which are highly soluble in styrene by using a stabilized emulsion of styrene in water (see 5.2), although this can only be done if the binder is completely insoluble in water. 4 Apparatus 4.1

21、Template, for cutting out test specimens measuring 125 mm 100 mm. 4.2 Trimming tool, for example a knife, a pair of scissors or a disc. 4.3 Beaker, minimum capacity 2 000 ml and minimum depth 195 mm. 4.4 Circular sieve, made of stainless steel, to fit the beaker (an example is shown in Figure 1), wi

22、th suspension arms long enough to ensure a distance of 50 mm between the lower clamp and the sieve. This sieve is used to remove the lower clamp and the disintegrated strands from the beaker at the end of the test. 4.5 Pair of clamps, made of stainless steel, suitable for gripping test specimens ove

23、r their whole width. The lower clamp shall have a total mass of 100 g 2 g and shall be balanced. An example of a suitable pair of clamps is shown in Figure 2. 4.6 Stop-watch, accurate to 1 s. BS ISO 2558:2010ISO 2558:2010(E) 2 ISO 2010 All rights reservedDimensions in millimetresKey 1 upper clamp 2

24、test specimen 3 lower clamp 4 sieveFigure 1 Sieve Figure 2 Example of a suitable apparatus 5 Solvent 5.1 Styrene monomer, d20= 0,907. Two litres of styrene allows 150 test specimens to be tested. 5.2 Stabilized emulsion of styrene in water, with a styrene concentration chosen from the following: 80

25、%, 60 %, 40 %, 20 %. Such emulsions can be prepared by the addition of a suitable emulsifying agent. BS ISO 2558:2010ISO 2558:2010(E) ISO 2010 All rights reserved 36 Test specimens 6.1 Selection Use at least five test specimens obtained as follows: Cut a strip measuring at least 125 mm in the roll l

26、ength direction from the whole width of the mat (see Figure 3). Using the template and trimming tool, cut from the strip: one 100 mm 125 mm test specimen at each end of the strip, but not nearer than 30 mm to the edges in the case of mats with trimmed edges and with a suitable extra allowance in the

27、 case of untrimmed mats plus at least three 100 mm 125 mm test specimens evenly distributed over the remaining width, in such a way that the length of the test specimens is parallel with the roll length direction, as shown in Figure 3. Dimensions in millimetres aRoll length direction. Figure 3 Cutti

28、ng out test specimens 6.2 Conditioning Condition the test specimens and styrene (or styrene emulsion) before the test for 1 h at the chosen test temperature (see Clause 7). BS ISO 2558:2010ISO 2558:2010(E) 4 ISO 2010 All rights reserved7 Procedure Carry out the test at one of the temperatures specif

29、ied in ISO 291, recording the chosen temperature in the test report. Ensure that not only the styrene (or styrene emulsion), but also the beaker, sieve and clamps, are at this temperature. It is recommended that a suitable ventilating system capable of dealing with styrene vapours be used. Fix the c

30、lamps to the ends of the test specimen in such a way as to leave a free area of dimensions 100 mm 100 mm between the clamps. Place the sieve (4.4) in the beaker (4.3) partly filled with styrene (5.1) or styrene emulsion (5.2). Immerse the lower clamp and test specimen in the styrene (or styrene emul

31、sion) in the beaker and ensure that the styrene (or styrene emulsion) reaches the level of the upper clamp. The distance between the bottom of the lower clamp and the sieve at this moment shall be 50 mm. Start the stop-watch when the upper clamp touches the rim of the beaker. Stop the stop-watch whe

32、n the lower clamp touches the sieve. Discontinue the test if the break has not occurred within 10 min. Record the time ti, in seconds, indicated by the stop-watch. Repeat the test for the remaining specimens. 8 Expression of results The time of dissolution of the binder of the chopped-strand mat und

33、er test is the arithmetic mean, in seconds (rounded to the nearest second), of the times, ti, noted for all the specimens tested. 9 Test report The test report shall include the following particulars: a) the reference number of this International Standard; b) all details necessary to identify the ma

34、t tested; c) the test temperature; d) the concentration of the styrene emulsion (if used); e) the individual values of the time of dissolution of the binder and their arithmetic mean; f) details of any operations not specified in this International Standard; g) details of any incidents which might h

35、ave influenced the results; h) the date of the test. BS ISO 2558:2010BS ISO 2558:2010ISO 2558:2010(E) ICS 59.100.10 Price based on 4 pages ISO 2010 All rights reserved This page deliberately left blankBSI is the independent national body responsible for preparing British Standardsand other standards

36、-related publications, information and services. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.British Standards Institution (BSI)raising standards worldwideBSI Group Headquarters389 Chiswick High Road London W4 4AL UKTel +44 (0)20

37、 8996 9001Fax +44 (0)20 8996 Standards are updated by amendment or revision. Users of British Stan-dards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and serv-ices. We would be grateful if anyone finding an

38、 inaccuracy or ambiguity whileusing this British Standard would inform the Secretary of the technical com-mittee responsible, the identity of which can be found on the inside frontcover.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers Members an individual updating service called PLUS whi

39、ch ensuresthat subscribers automatically receive the latest editions of standards.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, int

40、ernational and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, it is BSI policy tosupply the BSI implementation of those that have been publishedas British Standards, un

41、less otherwise requested.Information on standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: Various BSI electronic information services are also available whichgive det

42、ails on all its products and services. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048Email: BSI Subscribing Members are kept up to date with standardsdevelopments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Ad-min

43、istration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via BritishStandards Online can be found at information about BSI is available on the BSI website at www.bsi- subsists in all BSI publications. BSI also holds the copyright,

44、in the UK, of the publications of the international standardization bodies. Ex-cept as permitted under the Copyright, Designs and Patents Act 1988 no ex-tract may be reproduced, stored in a retrieval system or transmitted in anyform or by any means electronic, photocopying, recording or otherwise wi

45、thout prior written permission from BSI. This does not preclude the freeuse, in the course of implementing the standard of necessary details such assymbols, and size, type or grade designations. If these details are to be usedfor any other purpose than implementation then the prior written permissionof BSI must be obtained. Details and advice can be obtained from the Copy-right & Licensing Manager.Tel: +44 (0)20 8996 7070Email: