BS ISO 2540-2016 Centre drills for centre holes with protecting chamfer Type B《带护锥的中心孔用中心钻 B型》.pdf

《BS ISO 2540-2016 Centre drills for centre holes with protecting chamfer Type B《带护锥的中心孔用中心钻 B型》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 2540-2016 Centre drills for centre holes with protecting chamfer Type B《带护锥的中心孔用中心钻 B型》.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06Centre drills for centre holes with protecting chamfer Type BBS ISO 2540:2016National forewordThis British Standard is the UK implementation of ISO 2540:2016.The UK participation in its preparation was entrusted to Tech

2、nical Committee MTE/18, Tools tips and inserts for cutting applications.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct app

3、lication. The British Standards Institution 2016 Published by BSI Standards Limited 2016ISBN 978 0 580 83627 5ICS 25.100.30Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Com

4、mittee on 30 November 2016.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS ISO 2540:2016 ISO 2016Centre drills for centre holes with protecting chamfer Type BForets centrer pour centres avec chanfrein de protection Type BINTERNATIONAL STANDARDISO2540Second edition2

5、016-11-01Reference numberISO 2540:2016(E)BS ISO 2540:2016ISO 2540:2016(E)ii ISO 2016 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2016, Published in SwitzerlandAll rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or b

6、y any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCh. de Blandonnet 8 CP

7、401CH-1214 Vernier, Geneva, SwitzerlandTel. +41 22 749 01 11Fax +41 22 749 09 47copyrightiso.orgwww.iso.orgBS ISO 2540:2016ISO 2540:2016(E)Foreword ivIntroduction v1 Scope 12 Designation 13 Dimensions . 1Annex A (normative) Dimensions for centre hole Type B and choice of dimensioning method . 3Annex

8、 B (informative) Relationship between designations in this International Standard and ISO 13399 (all parts) 5Bibliography 6 ISO 2016 All rights reserved iiiContents PageBS ISO 2540:2016ISO 2540:2016(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of natio

9、nal standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. Internati

10、onal organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended

11、 for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso

12、.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will

13、be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expression

14、s related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html.The committee responsible for this document is ISO/TC 29, Small tools, Subcom

15、mittee SC 2, Holding tools, adaptive items and interfaces.This second edition cancels and replaces the first edition (ISO 2540:1973), of which it constitutes a minor revision, notably with the addition of Annex B, which gives the relationship between the designations of this International Standard a

16、nd the ISO 13399 series.iv ISO 2016 All rights reservedBS ISO 2540:2016ISO 2540:2016(E)IntroductionThis International Standard relates to centre drills and deals only with centre drills for centre holes with protecting chamfer Type B. It is a continuation of ISO 866 and precedes ISO 2541. ISO 2016 A

17、ll rights reserved vBS ISO 2540:2016This page deliberately left blankCentre drills for centre holes with protecting chamfer Type B1 Scope This International Standard specifies the dimensions of centre drills for centre holes with protecting chamfer Type B.It covers only metric dimensions, regarded a

18、s the only recommended dimensions in the future for this type of drills.The flutes can be straight or spiral at the option of manufacturer.Unless otherwise stated, these drills are right-hand cutting.Annex A gives the recommended dimensions for the centre holes, Type B, which can be obtained by a ra

19、tional use of the centre drills listed in this International Standard.2 DesignationCentre drills shall be designated by the type (Type B in this case), the pilot diameter, d (first column of Table 1) and the shank diameter d1(second column of Table 1).EXAMPLE B 2,5/10.3 DimensionsFigure 1 Centre dri

20、ll Type BINTERNATIONAL STANDARD ISO 2540:2016(E) ISO 2016 All rights reserved 1BS ISO 2540:2016ISO 2540:2016(E)Table 1Dimensions in millimetresdad1d2l Lk12 h9 k12 max. min. max. min.1,0 4,0 2,12 1,9 1,3 37, 5 33,5(1,25) 5,0 2,65 2,2 1,6 42 381,6 6,3 3,35 2,8 2,0 47 432,0 8,0 4,25 3,3 2,5 52 482,5 10

21、,0 5,30 4,1 3,1 59 533,15 11,2 6,70 4,9 3,9 63 574,0 14,0 8,50 6,2 5,0 70 64(5,0) 18,0 10,60 7, 5 6,3 78 726,3 20,0 13,20 9,2 8,0 83 77(8,0) 25,0 17,00 11,5 10,1 103 9710,0 31,5 21,20 14,2 12,8 128 122aSizes in brackets should be avoided whenever possible.2 ISO 2016 All rights reservedBS ISO 2540:20

22、16ISO 2540:2016(E)Annex A (normative) Dimensions for centre hole Type B and choice of dimensioning methodFigure A.1 Method 1Figure A.2 Method 2The two methods of dimensioning are practically equivalent. One or the other of these methods may be used. ISO 2016 All rights reserved 3BS ISO 2540:2016ISO

23、2540:2016(E)Table A.1Dimensions in millimetresMethod 1 Method 2danominalDnominall1nominaltref.1,0 3,15 1,27 0,9(1,25) 4 1,60 1,11,6 5 1,99 1,42,0 6,3 2,54 1,82,5 8 3,20 2,23,15 10 4,03 2,84,0 12,5 5,05 3,5(5,0) 16 6,41 4,46,3 18 7, 36 5,5(8,0) 22,4 9,35 7,010,0 28 11,66 8,7aSizes in brackets should

24、be avoided whenever possible.Dimensions depend on the length of the centre drill. It should not, even in the case of frilling with re-sharpened centre drills, be less than the reference value given in Table A.1.4 ISO 2016 All rights reservedBS ISO 2540:2016ISO 2540:2016(E)Annex B (informative) Relat

25、ionship between designations in this International Standard and ISO 13399 (all parts)For relationship between designations in this International Standard and preferred symbols according to ISO 13399 (all parts), see Table B.1.Table B.1 Relationship between designations in this International Standard

26、 and ISO 13399 (all parts)Symbol in ISO 2540Reference in ISO 2540Property name in ISO 13399 (all parts)Symbol in ISO 13399 (all parts)Reference in ISO 13399 (all parts)dFigure 1Table 1cutting diameter DC 71D084653E57Fd1Figure 1Table 1connection diameter machine sideDCONMS 71EBDBF5060E6d1h9 Table 1to

27、lerance class connection diameter machine sideTCDCONMS 72719B2BD8041LFigure 1Table 1overall length OAL 71D078EB7C08660 max Figure 1 countersink angle SIGCSK 726E2FCD1A3C4120 at dimension d1Figure 1 step included angle STA 71DF151D6E547120 at dimension dFigure 1 point angle SIG 71DCCC4FEF366 ISO 2016

28、 All rights reserved 5BS ISO 2540:2016ISO 2540:2016(E)Bibliography1 ISO 866, Centre drills for centre holes without protecting chamfers Type A2 ISO 2541, Centre drills for centre holes with radius form Type R3 ISO 13399 (all parts), Cutting tool data representation and exchange6 ISO 2016 All rights

29、reservedBS ISO 2540:2016This page deliberately left blankThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standard

30、ization products are published by BSI Standards Limited.British Standards Institution (BSI)About usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standar

31、ds has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to

32、succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website a

33、t where hard copies can also be purchased.If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.Copyright in BSI publicationsAll the content in BSI publications, including British Standards, is the

34、property of and copyrighted by BSI or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use.Save for the provisions below, you may not transfer, share o

35、r disseminate any portion of the standard to any other person. You may not adapt, distribute, commercially exploit, or publicly display the standard or any portion thereof in any manner whatsoever without BSIs prior written consent.Storing and using standardsStandards purchased in soft copy format:

36、A British Standard purchased in soft copy format is licensed to a sole named user for personal or internal company use only. The standard may be stored on more than 1 device provided that it is accessible by the sole named user only and that only 1 copy is accessed at any one time. A single paper co

37、py may be printed for personal or internal company use only. Standards purchased in hard copy format: A British Standard purchased in hard copy format is for personal or internal company use only. It may not be further reproduced in any format to create an additional copy. This includes scanning of

38、the document.If you need more than 1 copy of the document, or if you wish to share the document on an internal network, you can save money by choosing a subscription product (see Subscriptions).Reproducing extractsFor permission to reproduce content from BSI publications contact the BSI Copyright &

39、Licensing team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international stan

40、dards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date.You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member.P

41、LUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced.To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (

42、MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .RevisionsOur British Standards and other publi

43、cations are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.Useful ContactsCustomer ServicesTel: +4

44、4 345 086 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 345 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: BSI Group Headquarters389 Chiswick High Road London W4 4AL UKNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW