BS ISO 2332-2009 Agricultural tractors and machinery - Connection of implements via three-point linkage - Clearance zone around implement《农业拖拉机和机械 通过三点拉杆进行器具的连接 器具周围空隙区》.pdf

《BS ISO 2332-2009 Agricultural tractors and machinery - Connection of implements via three-point linkage - Clearance zone around implement《农业拖拉机和机械 通过三点拉杆进行器具的连接 器具周围空隙区》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 2332-2009 Agricultural tractors and machinery - Connection of implements via three-point linkage - Clearance zone around implement《农业拖拉机和机械 通过三点拉杆进行器具的连接 器具周围空隙区》.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、BS ISO 2332:2009ICS 65.060.01NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDAgricultural tractorsand machinery Connection ofimplements via three-point linkage Clearance zone aroundimplementThis British Standardwas published under theauthority of the StandardsPo

2、licy and StrategyCommittee on 28 February2009 BSI 2009ISBN 978 0 580 56216 7Amendments/corrigenda issued since publicationDate CommentsBS ISO 2332:2009National forewordThis British Standard is the UK implementation of ISO 2332:2009. Itsupersedes BS 6509:1984 which is withdrawn.The UK participation i

3、n its preparation was entrusted to TechnicalCommittee AGE/6, Agricultural tractors and forestry machinery.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are

4、 responsible for its correct application.Compliance with a British Standard cannot confer immunityfrom legal obligations.BS ISO 2332:2009Reference numberISO 2332:2009(E)ISO 2009INTERNATIONAL STANDARD ISO2332Third edition2009-01-15Agricultural tractors and machinery Connection of implements via three

5、-point linkage Clearance zone around implement Tracteurs et matriels agricoles Liaisons des instruments par lattelage trois points Zone de dgagement autour de linstrument BS ISO 2332:2009ISO 2332:2009(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing

6、 policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Cen

7、tral Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been ta

8、ken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2009 All rights reserved. Unless otherwise specified, no part of this

9、 publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211

10、 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2009 All rights reservedBS ISO 2332:2009ISO 2332:2009(E) ISO 2009 All rights reserved iiiForeword ISO (the International Organization for Standardization) is a worldwide fe

11、deration of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that com

12、mittee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accord

13、ance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard require

14、s approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 2332 was prepared by Technical C

15、ommittee ISO/TC 23, Tractors and machinery for agriculture and forestry, Subcommittee SC 4, Tractors. This third edition cancels and replaces the second edition (ISO 2332:1993), which has been technically revised. BS ISO 2332:2009BS ISO 2332:2009INTERNATIONAL STANDARD ISO 2332:2009(E) ISO 2009 All r

16、ights reserved 1Agricultural tractors and machinery Connection of implements via three-point linkage Clearance zone around implement 1 Scope This International Standard specifies the clearance zone around an implement for attachment to the three-point linkage of an agricultural wheeled tractor. It i

17、s applicable to the connection of agricultural implements to three-point linkages complying with ISO 730, and also where implement couplers complying with ISO 11001-1, ISO 11001-2, ISO 11001-3 and ISO 11001-4 are used. 2 Normative references The following referenced documents are indispensable for t

18、he application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 730:2009, Agricultural wheeled tractors Rear-mounted three-point linkage Categories 1N, 1, 2N, 2, 3N, 3

19、, 4N and 4 ISO 11001 (all parts), Agricultural wheeled tractors and implements Three-point hitch couplers 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 implement coupler device which facilitates the connection of tractor three-point linkage

20、 to the implement 3.2 transport pitch pitch reached by the mast when lifted to standard transport height from a position with lower links horizontal and mast vertical ISO 730:2009, 3.2.24 4 Specifications The shape and dimensions of the clearance zone around implements for attachment to a three-poin

21、t linkage shall be as shown in Figures 1 to 4 and as given in Table 1. Not included are adjustable levers and handles used to operate the implement, or specifications referring to the width of the implements. BS ISO 2332:2009ISO 2332:2009(E) 2 ISO 2009 All rights reservedDimensions in millimetres Ke

22、y 1 lower hitch point X hitch pin on both sides 2 upper hitch point Y clevis mounting on both sides aA or B (see Table 1). NOTE For dimension b5, see ISO 730. Figure 1 Clearance zone of implements where transport pitch extends forward of vertical in raised position (view of details) BS ISO 2332:2009

23、ISO 2332:2009(E) ISO 2009 All rights reserved 3Figure 2 Clearance zone of implements where transport pitch extends forward of vertical in raised position (perspective view) BS ISO 2332:2009ISO 2332:2009(E) 4 ISO 2009 All rights reservedDimensions in millimetres Key 1 lower hitch point X hitch pin on

24、 both sides 2 upper hitch point Y clevis mounting on both sides aA or B (see Table 1). NOTE For dimension b5, see ISO 730. Figure 3 Clearance zone of implements where transport pitch does not extend forward of vertical in raised position (view of details) BS ISO 2332:2009ISO 2332:2009(E) ISO 2009 Al

25、l rights reserved 5Figure 4 Clearance zone of implements where transport pitch shall not extend forward of vertical in raised position (perspective view) BS ISO 2332:2009ISO 2332:2009(E) 6 ISO 2009 All rights reservedTable 1 Dimensions Dimensions in millimetres Tractor categorya1N 1 2N 2 3N 3 4N 4 S

26、ymbol Description min. max. min. max. min. max. min. max. min. max. min. max. min. max. min. max.Ab Upper hitch pin, vertical clearance 310 310 460 460 460 460 460 460 B Upper hitch pin, vertical clearance 160 160 280 280 280 280 280 280 C Hitch pins, horizontal position 35 35 35 35 40 40 40 40 D Lo

27、wer hitch pin, horizontal clearance 95 95 95 95 105 105 135 135 E Lower hitch pin, vertical position 230 230 230 230 245 245 245 245 H Upper hitch pin, horizontal clearance 80 80 80 80 90 90 120 120 L Lower hitch pin, vertical position 150 150 150 150 200 200 200 200 S Upper hitch pin, width clearan

28、ce 52 52 52 52 52 52 65 65 M c, dMast height See ISO 730. N cLower hitch point span See ISO 730. P Diameter of hitch pin shoulder See ISO 11001-3. aTractor categories according to ISO 730.bDimension A applies where it is necessary to accommodate the upper hook to the coupler complying with ISO 11001

29、-1. cIt may be necessary to vary this dimension in the case of specialized implements. dIf U-frame couplers according to ISO 11001-1, are used, dimension M should be in line with the upper hook vertical spacing as specified in ISO 11001-1. BS ISO 2332:2009BS ISO 2332:2009ISO 2332:2009(E) ICS 65.060.

30、01 Price based on 6 pages ISO 2009 All rights reserved BS ISO 2332:2009This page has been intentionally left blank BS ISO2332:2009BSI GroupHeadquarters 389Chiswick High Road,London, W4 4AL, UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 - British Standards InstitutionBSI is the independent national bo

31、dy responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at theinternational level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest am

32、endments oreditions.It is the constant aim of BSI to improve the quality of our products and services.We would be grateful if anyone finding an inaccuracy or ambiguity while usingthis British Standard would inform the Secretary of the technical committeeresponsible, the identity of which can be foun

33、d on the inside front cover. Tel:+44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards pu

34、blications should beaddressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 89967001 Email: You may also buy directly using a debit/creditcard from the BSI Shop on the Website http:/ response to orders for international standards, it is BSI policy to supply theBSI implementation of

35、 those that have been published as British Standards,unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European andinternational standards through its Library and its Technical Help to ExportersService. Various BSI electronic information service

36、s are also available whichgive details on all its products and services. Contact Information Centre. Tel:+44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subscribing members of BSI are kept up to date with standards developmentsand receive substantial discounts on the purchase price of standards.

37、 For detailsof these and other benefits contact Membership Administration. Tel: +44 (0)208996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via British StandardsOnline can be found at http:/ information about BSI is available on the BSI website at http

38、:/CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in theUK, of the publications of the international standardization bodies. Except aspermitted under the Copyright, Designs and Patents Act 1988 no extract maybe reproduced, stored in a retrieval system or transmitte

39、d in any form or by anymeans electronic, photocopying, recording or otherwise without prior writtenpermission from BSI.This does not preclude the free use, in the course of implementing the standard,of necessary details such as symbols, and size, type or grade designations. Ifthese details are to be used for any other purpose than implementation then theprior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright and Licensing Manager.Tel: +44 (0)20 8996 7070 Email: