BS ISO 21287-2004 Pneumatic fluid power - Cylinders - Compact cylinders 1000 kPa (10 bar) series bores from 20 mm to 100 mm《气压传动 气缸 1000kPa(10bar)系列、缸径从20mm到100mm的小型缸》.pdf

《BS ISO 21287-2004 Pneumatic fluid power - Cylinders - Compact cylinders 1000 kPa (10 bar) series bores from 20 mm to 100 mm《气压传动 气缸 1000kPa(10bar)系列、缸径从20mm到100mm的小型缸》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 21287-2004 Pneumatic fluid power - Cylinders - Compact cylinders 1000 kPa (10 bar) series bores from 20 mm to 100 mm《气压传动 气缸 1000kPa(10bar)系列、缸径从20mm到100mm的小型缸》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS ISO 21287:2004 Pneumatic fluid power Cylinders Compact cylinders, 1 000 kPa (10 bar) series, bores from 20 mm to 100 mm ICS 23.100.20 BS ISO 21287:2004 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 19 November 2004 BSI 1

2、9 November 2004 ISBN 0 580 44825 8 National foreword This British Standard reproduces verbatim ISO 21287:2004 and implements it as the UK national standard. The UK participation in its preparation was entrusted to Technical Committee MCE/18, Fluid power systems, which has the responsibility to: A li

3、st of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspo

4、ndence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of

5、itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments a

6、nd promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the ISO title page, pages ii to iv, pages 1 to 7 and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since pub

7、lication Amd. No. Date Comments Reference number ISO 21287:2004(E) OSI 4002INTERNATIONAL STANDARD ISO 21287 First edition 2004-07-01 Pneumatic fluid power Cylinders Compact cylinders, 1 000 kPa (10 bar) series, bores from 20 mm to 100 mm Transmissions pneumatiques Vrins Vrins compacts, srie 1 000 kP

8、a (10 bar), alsages de 20 mm 100 mm BSISO21287:2004IS:78212 O4002(E) DPlcsid Fremia ihTs PDF file may ctnoian emdebt dedyfepcaes. In ccaocnadrw eith Aebods licensilop gnic,y this file mairp eb ynted iv roweb detu slahl ton ide ebtlnu deess the typefaces whice era hml era deddebicsnede to i dnanstlal

9、ed t noeh computfrep reormign tide ehtin.g In wodlnidaot gnhis file, trapise atpecc tiereht nser ehnopsiiblity fo not infriigngn Aebods licensilop gnic.y ehT ISO tneClar Secrteiraat caceptl on siibality in this .aera Ai ebods a tredamafo kr Aebod SystemI sncotaropr.de teDails fo teh softwacudorp ert

10、s sut deo crtaee this PDF file cna f ebi dnuon tlareneG eh Info leratit evo the file; tP ehDc-Frtaeion marapterew setpo erimizde for irpnti.gn Evyre caer neeb sah taken to sneeru that the file is suitlbae fosu re yb ISO memdob rebeis. In tlnu ehikletneve y ttah lborp aem leratit gno it is f,dnuo pls

11、aee inform ttneC ehlar Secrteiraat ta the serddaig sleb nevwo. ISO 4002 All irthgs erse.devr lnUeto sswrehise specified, on trap fo this lbupictaion maeb y cudorperro de tuilizi den yna form ro na ybm ynae,s lecetrinoc ro mecinahcal, inclidung tohpcoiypodna gn micrfoilm, wittuoh repmissii non writig

12、n from ietI rehSa Ot tsserdda eh ebolw or ISOs memreb i ydobn the cnuotrfo y ttseuqer ehe.r ISO cirypothg fofice saCe tsopale 65 eneG 1121-HC 02 av leT. 4 + 10 947 22 1 11 xaF0 947 22 14 + 9 74 E-mail coirypthgiso.o gr We bwww.is.o gro Pulbisdehi n Switlrez dnaii ISO 4002 Allr ithgsr esedevrBSISO212

13、87:2004IS:78212 O4002(E) I SO 4002 All irthgs ersedevr iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committe

14、es. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the Inte

15、rnational Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International S

16、tandards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the su

17、bject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 21287 was prepared by Technical Committee ISO/TC 131, Fluid power systems, Subcommittee SC 3, Cylinders. BSISO21287:2004IS:78212 O4002(E) iv I SO 4002 All irthgs ersedevrIntroduction In pneum

18、atic fluid power systems, power is transmitted and controlled through a gas under pressure within a circuit. One component of such system is the pneumatic cylinder. This is a device which converts power into linear force and motion. It consists of a movable element, i.e. a piston, and a piston rod,

19、operating within a cylindrical bore. The compact cylinder series without cushioning allows the application of pneumatic cylinders within systems where “normal” pneumatic cylinder series because of their mounting dimensions cannot be used. BSISO21287:2004INTENRATIONAL TSANDADR IS:78212 O4002(E)I SO 4

20、002 All irthgs ersedevr 1Pneumatic fluid power Cylinders Compact cylinders, 1 000 kPa (10 bar) series, bores from 20 mm to 100 mm 1 Scope This International Standard establishes a metric series of single rod pneumatic compact cylinders with bores of 20 mm to 100 mm for use of at maximum working pres

21、sure of 1 000 kPa (10 bar 1) ) with and without magnetic function. This series of pneumatic cylinder is not equipped with adjustable cushioning. Therefore, the application is restricted to those systems where adjustable cushioning is not required. Cylinders with bores of 20 mm and 25 mm can be used

22、with end cover mountings in accordance with this International Standard. Cylinders with bores from 32 mm to 100 mm can be used with end cover mountings in accordance with ISO 15552. Piston rod mountings can be used for the different bores in accordance with ISO 8139 and ISO 8140. 2 Normative referen

23、ces The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 3320, Fluid power systems and components

24、Cylinder bores and piston rod diameters Metric series ISO 4393, Fluid power systems and components Cylinders Basic series of piston strokes ISO 5598, Fluid power systems and components Vocabulary ISO 6099, Fluid power systems and components Cylinders Identification code for mounting dimensions and m

25、ounting types ISO 8139, Pneumatic fluid power Cylinders, 1 000 kPa (10 bar) series Rod end spherical eyes Mounting dimensions ISO 8140, Pneumatic fluid power Cylinders 1 000 kPa (10 bar) Rod end clevis Mounting dimensions ISO 15552, Pneumatic fluid power Cylinders with detachable mountings, 1 000 kP

26、a (10 bar) series, bores from 32 mm to 320 mm Basic, mounting and accessories dimensions ISO 16030, Pneumatic fluid power Connections Ports and stud ends 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 5598 and the following apply. 1) 1 bar = 0,1 MPa

27、 = 10 5Pa; 1 Pa = 1 N/m 2BSISO21287:2004IS:78212 O4002(E) 2 I SO 4002 All irthgs ersedevr4 Bore sizes Cylinders with the following bore dimensions, AL, expressed in millimetres, are included in this series, in accordance with ISO 3320: 20 - 25 - 32 - 40 - 50 - 63 - 80 - 100 5 Nominal stroke 5.1 The

28、nominal strokes shall be selected from the recommended values given in ISO 4393, as shown in Figure 1. The maximum stroke length should not exceed 500 mm. 5.2 The nominal stroke tolerances are given in Table 1. Figure 1 Stroke, S Table 1 Nominal strokes tolerances Dimensions in millimetres Bore AL N

29、ominal stroke tolerance 20 25 1,5 0 +32 40 50 2 0 +63 80 100 2,5 0 +6 Dimensions 6.1 Cylinder basic dimensions shall conform to the requirements given in Figure 2 and Table 2. 6.2 Mounting dimensions shall conform to the requirements given in Figures 3 to 5 and Tables 3 to 5. BSISO21287:2004IS:78212

30、 O4002(E) I SO 4002 All irthgs ersedevr 37 Mounting types This standard includes the following mounting types in accord with ISO 6099: MP4: Cap, detachable plain eyes (see Figure 3 and Table 3); MF1: Head, rectangular flange (see Figure 4 and Table 4); MF2: Cap, rectangular flange (see Figure 4 and

31、Table 4); MS1: End angles (see Figure 5 and Table 5). 8 Identification statement (reference to this International Standard) Use the following statement in test reports, catalogues, and sales literature when electing to comply with this International Standard: “Dimensions of pneumatic compact cylinde

32、r are in accordance with ISO 21287:2004, Pneumatic fluid power Cylinders Compact cylinders, 1 000 kPa (10 bar) series, bores from 20 mm to 100 mm.” BSISO21287:2004IS:78212 O4002(E) 4 I SO 4002 All irthgs ersedevrAlternative: with male thread Key 1 drive for screw aTRP: Theoretical reference point ac

33、cording to ISO 6099. Figure 2 Basic dimensions Table 2 Basic dimensions Dimensions in millimetres Bore AL AF A WH ZA ZB aKF KK EE bBG RR TG E RT LA PL min. 0 0,5 nom. tol. nom. tol. nom. tol. min. min. nom. tol. max. max. min. 20 10 16 6 1,4 37 0,5 43 1,4 M6 M8 1,25 M5 15 4,1 22 0,4 38 M5 5 5 25 10

34、16 6 1,4 39 0,5 45 1,4 M6 M8 1,25 M5 15 4,1 26 0,4 41 M5 5 5 32 12 19 7 1,6 44 0,5 51 1,6 M8 M10 1,25 G1/8 16 5,1 32,5 0,5 50 M6 5 7,5 40 12 19 7 1,6 45 0,7 52 1,6 M8 M10 1,25 G1/8 16 5,1 38 0,5 58 M6 5 7,5 50 16 22 8 1,6 45 0,7 53 1,6 M10 M12 1,25 G1/8 16 6,4 46,5 0,6 70 M8 5 7,5 63 16 22 8 1,6 49

35、0,8 57 1,6 M10 M12 1,25 G1/8 16 6,4 56,5 0,7 80 M8 5 7,5 80 20 28 10 2,0 54 0,8 64 2,0 M12 M16 1,5 G1/8 17 8,4 72 0,7 96 M10 5 7,5 100 20 28 10 2,0 67 1,0 77 2,0 M12 M16 1,5 G1/8 17 8,4 89 0,7 116 M10 5 7,5 NOTE Dimensions WH, ZA+ and ZB+ are values for non-pressurised cylinders due to deformation o

36、f elastic buffers at stroke ends. NOTE Nominal stroke S u 500. aOnly for reference. bIn accordance with ISO 16030. BSISO21287:2004IS:78212 O4002(E) I SO 4002 All irthgs ersedevr 5Figure 3 Cap, detachable plain eyes (MP4) Table 3 Dimensions of cap, detachable plain eyes (MP4) Dimensions in millimetre

37、s Bore Screw size AL E EW TG FL L L 4CD MR XD max. 0,2 0,6 0,2 0,2 min 0,3 0 +H9 max. 20 38 16 22 20 12 3 8 9 M5 16 63 25 41 16 26 20 12 3 8 9 M5 16 65 aTRP BSISO21287:2004IS:78212 O4002(E) 6 I SO 4002 All irthgs ersedevrFigure 4 Head, rectangular flange (MF1) and cap, rectangular flange (MF2) Table

38、 4 Dimensions of head, rectangular flange (MF1) and cap, rectangular flange (MF2) Dimensions in millimetres Bore Screw size AL D FB TG E MF TF UF L 4W ZF ZB H11 H13 0,2 max. js14 js13 max. 0 0,5 ref. 20 16 6,6 22 38 8 55 70 3 M5 16 2 51 43 25 16 6,6 26 41 8 60 76 3 M5 16 2 53 45 aTRP BSISO21287:2004

39、IS:78212 O4002(E) I SO 4002 All irthgs ersedevr 7Figure 5 End angles (MS1) Table 5 Dimensions of end angles (MS1) Dimensions in millimetres Bore Screw size AL AB TG E TR AO AU AH L 7AT R 2SA XA H14 0,2 max. JS14 max. 0,2 JS16 2 0,5 nom. tol. nom. tol. 20 7 22 38 22 7 16 27 22 4 M5 16 69 59 25 7 26 4

40、1 26 7 16 29 22 4 M5 16 71 61 32 7 32,5 50 32 7 16 33,5 24,5 4 M6 16 15 76 67 40 10 38 58 36 9 18 38 26 4 M6 16 17,5 81 70 50 10 46,5 70 45 9 21 45 31 5 M8 20 20 87 1,25 74 1,25 63 10 56,5 80 50 9 21 50 31 5 M8 20 22.5 91 78 80 12 72 96 63 11 26 63 40,5 6 M10 20 22,5 106 90 100 14,5 89 116 75 13 27

41、74 47 6 M10 20 27,5 121 1,6 104 1,6 aTRP BSISO21287:2004BS ISO 21287:2004 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the internation

42、al level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We woul

43、d be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an indi

44、vidual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 700

45、1. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards

46、 BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Cen

47、tre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +

48、44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-. Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted un