BS ISO 20653-2013 Road vehicles Degrees of protection (IP code) Protection of electrical equipment against foreign objects water and access《道路车辆 防护等级(IP代码) 电子设备对外来物体、水和通道的防护》.pdf

《BS ISO 20653-2013 Road vehicles Degrees of protection (IP code) Protection of electrical equipment against foreign objects water and access《道路车辆 防护等级(IP代码) 电子设备对外来物体、水和通道的防护》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 20653-2013 Road vehicles Degrees of protection (IP code) Protection of electrical equipment against foreign objects water and access《道路车辆 防护等级(IP代码) 电子设备对外来物体、水和通道的防护》.pdf（34页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS ISO 20653:2013Road vehicles Degreesof protection (IP code) Protection of electricalequipment against foreignobjects, water and accessBS ISO 20653:2013 BRITISH STANDARDNational

2、 forewordThis British Standard is the UK implementation of ISO 20653:2013. Itsupersedes BS ISO 20653:2006 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee AUE/16, Electrical and electronic equipment.A list of organizations represented on this committee c

3、an beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2013. Published by BSI StandardsLimited 2013ISBN 978 0 580 74258 3ICS 43.040.10Complia

4、nce with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 March 2013.Amendments issued since publicationDate Text affectedBS ISO 20653:2013 ISO 2013Road vehicles Degrees of prot

5、ection (IP code) Protection of electrical equipment against foreign objects, water and accessVhicules routiers Degrs de protection (codes IP) Protection des quipements lectriques contre les corps trangers, leau et les contactsINTERNATIONAL STANDARDISO20653Second edition2013-02-15Reference numberISO

6、20653:2013(E)BS ISO 20653:2013ISO 20653:2013(E)ii ISO 2013 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2013All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including pho

7、tocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 4

8、7E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 20653:2013ISO 20653:2013(E) ISO 2013 All rights reserved iiiContents PageForeword ivIntroduction v1 Scope . 12 Normative references 13 Terms and definitions . 14 Structure and meaning of the IP code 24.1 Structure of the IP code .

9、 24.2 Meaning of IP code. 24.3 Examples for the use of letters in the IP code 35 Degrees of protection against foreign objects and against access 46 Degrees of protection against water 57 Designation examples . 67.1 General . 67.2 Example IP34K 67.3 Example IP16KB 67.4 Example IP2X/IP5KX . 78 Requir

10、ements and testing . 78.1 Atmospheric conditions 78.2 Device under test (DUT) . 78.3 Requirements and tests for degrees of protection against foreign objects and access 78.4 Requirements and test for degrees of protection against water .139 Notes on the assignment of degrees of protection .149.1 Ass

11、ignment of degrees of protection against foreign objects and access .149.2 Assignment of degrees of protection against water 14Bibliography .23BS ISO 20653:2013ISO 20653:2013(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (IS

12、O member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, gove

13、rnmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.International Standards are drafted in accordance with the rules given in the ISO/IEC D

14、irectives, Part 2.The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member b

15、odies casting a vote.Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.ISO 20653 was prepared by Technical Committee ISO/TC 22, Road vehicles, Subcommit

16、tee SC 3, Electrical and electronic equipment.This second edition cancels and replaces the first edition (ISO 20653:2006), which has been technically revised.iv ISO 2013 All rights reservedBS ISO 20653:2013ISO 20653:2013(E)IntroductionThe IP codes used in this International Standard are in accordanc

17、e with IEC 60529, except in the case of codes “K”, which describe special requirements for road vehicles that are not covered by IEC 60529. ISO 2013 All rights reserved vBS ISO 20653:2013BS ISO 20653:2013Road vehicles Degrees of protection (IP code) Protection of electrical equipment against foreign

18、 objects, water and access1 ScopeThis International Standard applies to degrees of protection (IP code) provided by enclosures of the electrical equipment of road vehicles. It specifies the following:a) Designations and definitions of types and degrees of protection provided by enclosures of electri

19、cal equipment (IP codes) for the: protection of electrical equipment within the enclosure against ingress of foreign objects, including dust (protection against foreign objects); protection of persons against access to hazardous parts inside the enclosure (protection against access); protection of e

20、lectrical equipment inside the enclosure against effects due to ingress of water (protection against water).b) Requirements for each degree of protection.c) Tests to be carried out in order to confirm that the enclosure complies with requirements of the relevant degree of protection.2 Normative refe

21、rencesThe following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 12103-1, Road vehicles Test dust for fil

22、ter evaluation Part 1: Arizona test dustIEC 60068-2-68, Environmental testing Part 2: Tests Test L: Dust and sand3 Terms and definitionsFor the purposes of this document, the following terms and definitions apply.3.1enclosurepart providing protection of equipment against certain external influences

23、and in any direction against access3.2degree of protectionprotection provided by an enclosure against access, foreign objects and/or water and verified by standardized test methodsINTERNATIONAL STANDARD ISO 20653:2013(E) ISO 2013 All rights reserved 1BS ISO 20653:2013ISO 20653:2013(E)3.3Internationa

24、l Protection codeIP codecoding system to indicate the degree of protection provided by an enclosure against access, foreign objects and/or water and to give additional information in connection with such parts3.4hazardous partpart that is hazardous to approach or touch3.5openinggap or aperture in an

25、 enclosure which exists or may be formed by the application of a test probe at the specified force4 Structure and meaning of the IP code4.1 Structure of the IP codeThe structure of the IP code is as follows.Where no code element is given, the letter “X” shall be substituted (or “XX”, if none of the

26、two code elements have been indicated).Additional and/or supplementary letters may be omitted without substitute.Additional letters following each other directly shall be in alphabetical order.Wherever the degree of protection of a part of the enclosure or the electrical equipment deviates from the

27、degree of protection of the remaining part, both degrees of protection shall be indicated.4.2 Meaning of IP codeTable 1 contains an overview of the IP code elements.2 ISO 2013 All rights reservedBS ISO 20653:2013ISO 20653:2013(E)Table 1 Overview of all IP code elements and meaningElement IP Meaning

28、for the protection of electrical equipmentMeaning for the protection of personsFirst code element Against foreign objects (including dust): Against access:0 not protected not protected1 with diameter 50 mm with back of hand2 with diameter 12,5 mm with finger3 with diameter 2,5 mm with tool4 with dia

29、meter 1,0 mm with wire5K dust-protected with wire6K dust-tight with wireSecond code elementAgainst water: Not applicable0 not protected1 vertical water drips2 water drips (15 inclination)3 water spray4 splash water4K splash water with increased pressure5 high-velocity water6 strong high-velocity wat

30、er6K strong high-velocity water with increased pressure7 temporary immersion8 continuous submersion9K high-pressure/steam-jet cleaningAdditional letter (optional)Not applicable Against access (unless described by first letter)A with back of handB with fingerC with toolD with wireSupplementary letter

31、 (optional)M Movement of moveable parts during water test Not applicableS Standstill of moveable parts during water test4.3 Examples for the use of letters in the IP codeThe following examples explain the use and arrangements of letters in the IP code. For more comprehensive examples, see Clause 7.I

32、P44 no letters, no options;IPX5 omitting first code element;IP2X omitting second code element;IP20C using additional letter;IPXXC omitting both code elements, using additional letter; ISO 2013 All rights reserved 3BS ISO 20653:2013ISO 20653:2013(E)IPX1C omitting first code element, using additional

33、letter;IP3XD omitting second code element, using additional letter;IP23S using supplementary letter;IP21CM using additional letter and supplementary letter;IPX5/IPX7 giving two different degrees of protection by an enclosure against both water jets and temporary immersion for “versatile” application

34、.5 Degrees of protection against foreign objects and against accessTables 2 and 3 contain short descriptions of the degrees of protection with the relevant requirements.If the same degree of protection (identical code element) for protection against foreign objects and access is required, then both

35、requirements are indicated by the first code element.If different degrees of protection for both protection types are required, then an additional letter shall be used. In this case the first code element only defines the protection against foreign objects and the additional letter indicates the pro

36、tection against access.Additional letters may only be used if: the degree of protection against access is higher than indicated by the first code element, or only the degree of protection against access is to be indicated (first code element substituted by X).The indication of a degree of protection

37、 against access and foreign objects always includes the preceding degrees of protection.Table 2 Degrees of protection against foreign objectsFirst code elementDegree of protectionBrief description Requirements0 not protected None1 foreign objects diameter 50 mmTest probe with diameter 50 mm shall no

38、t penetrate completely.2 foreign objects diameter 12,5 mmTest probe with diameter 12,5 mm shall not penetrate completely.3 foreign objects diameter 2,5 mmTest probe with diameter 2,5 mm shall not penetrate completely.4 foreign objects diameter 1,0 mmTest probe with diameter 1,0 mm shall not penetrat

39、e completely.5K dustDust shall only penetrate in quantities which do not impair performance and safety.6K dust Dust shall not penetrate.NOTE “Shall not penetrate completely” indicates that the full diameter shall not pass through an opening of the enclosure.4 ISO 2013 All rights reservedBS ISO 20653

40、:2013ISO 20653:2013(E)Table 3 Degrees of protection against accessFirst code elementAdditional letterDegree of protectionBrief description Requirements0 not protected None1 Aback of hand (no protection against intentional contact)Test probe with diameter 50 mm shall not penetrate com-pletely and mai

41、ntain sufficient distance from hazardous parts.2 B fingerJointed test finger with diameter 12 mm may penetrate completely, but shall maintain a sufficient distance from hazardous parts.3 C tool (e.g. screwdriver)Test probe with diameter 2,5 mm, 100 mm long, may pen-etrate completely, but shall maint

42、ain a sufficient distance from hazardous parts.4 D wire Test probe with diameter 1,0 mm, 100 mm long, may pen-etrate completely, but shall maintain a sufficient distance from hazardous parts.5K D wire6K D wireNOTE “Shall not penetrate completely” indicates that the full diameter shall not pass throu

43、gh an opening of the enclosure.6 Degrees of protection against waterTable 4 contains short descriptions of the degrees of protection with the relevant requirements.Up to and including degree of protection 6K for the protection against water, the designation implies compliance also with the requireme

44、nts for all lower degrees of protection.For degrees of protection against water 7, 8 and 9K, lower degrees of protection up to and including 6K are not covered by the designation. In such cases where a lower degree of protection up to and including 6K is required in addition to protection against wa

45、ter 7, 8 or 9K, it shall be indicated separately, e.g. IPX4K/IPX7, IPX5/IPX7, IPX6K/IPX8 and IPX6K/IPX9K.Table 4 Degrees of protection against waterSecond code elementDegree of protectionBrief description Requirements0 not protected None1 water drips verticallyVertical drips shall not have any harmf

46、ul effects or impair perfor-mance.2water drips with enclosure inclined by 15Vertical drips shall not have any harmful effects or impair perfor-mance when the enclosure is tilted at any angle up to 15 on either side of the vertical.3 water sprayWater spray at an angle up to 60 on either side of the v

47、ertical shall have no harmful effects or impair performance.4 splash waterWater which splashes against the enclosure from any direction shall not have any harmful effects or impair performance.4Ksplash water with increased pressureWater which splashes against the enclosure from any direction with in

48、creased pressure shall not have any harmful effects or impair performance.5 high-velocity waterWater which is directed against the enclosure from any direction as a jet shall not have any harmful effects or impair performance. ISO 2013 All rights reserved 5BS ISO 20653:2013ISO 20653:2013(E)Second co

49、de elementDegree of protectionBrief description Requirements6 strong high-velocity waterWater which is directed against the enclosure from any direction as a strong jet shall not have any harmful effects or impair perfor-mance.6Kstrong high-velocity water with increased pressureWater which is directed against the enclosure from any direction as a strong jet with increased pressure shall not have any harm