BS ISO 20401-2017 Pneumatic fluid power systems Directional control valves Specification of pin assignment for 8 mm and 12 mm diameter electrical round connectors《气动液压驱动系统 方向控制阀 8m.pdf

《BS ISO 20401-2017 Pneumatic fluid power systems Directional control valves Specification of pin assignment for 8 mm and 12 mm diameter electrical round connectors《气动液压驱动系统 方向控制阀 8m.pdf》由会员分享，可在线阅读，更多相关《BS ISO 20401-2017 Pneumatic fluid power systems Directional control valves Specification of pin assignment for 8 mm and 12 mm diameter electrical round connectors《气动液压驱动系统 方向控制阀 8m.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、Pneumatic fluid power systems Directional control valves Specification of pin assignment for 8 mm and 12 mm diameter electrical round connectorsBS ISO 20401:2017BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06 ISO 2017Pneumatic fluid power systems Directional control

2、 valves Specification of pin assignment for 8 mm and 12 mm diameter electrical round connectorsTransmissions pneumatiques Distributeurs de commande directionnels Spcification de laffectation des broches des connecteurs lectriques ronds de diamtres 8 mm et 12 mmINTERNATIONAL STANDARDISO20401Second ed

3、ition2017-07Reference numberISO 20401:2017(E)National forewordThis British Standard is the UK implementation of ISO 20401:2017. It supersedes BS ISO 20401:2005, which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee MCE/18/-/5, Control components.A list of or

4、ganizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2017 Published by BSI Standards Limited

5、2017ISBN 978 0 580 91688 5ICS 23.100.50Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 August 2017.Amendments/corrigenda issued since publicationDate Text aff

6、ectedBRITISH STANDARDBS ISO 20401:2017 ISO 2017Pneumatic fluid power systems Directional control valves Specification of pin assignment for 8 mm and 12 mm diameter electrical round connectorsTransmissions pneumatiques Distributeurs de commande directionnels Spcification de laffectation des broches d

7、es connecteurs lectriques ronds de diamtres 8 mm et 12 mmINTERNATIONAL STANDARDISO20401Second edition2017-07Reference numberISO 20401:2017(E)BS ISO 20401:2017ISO 20401:2017(E)ii ISO 2017 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2017, Published in SwitzerlandAll rights reserved. Unless oth

8、erwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address

9、 below or ISOs member body in the country of the requester.ISO copyright officeCh. de Blandonnet 8 CP 401CH-1214 Vernier, Geneva, SwitzerlandTel. +41 22 749 01 11Fax +41 22 749 09 47copyrightiso.orgwww.iso.orgBS ISO 20401:2017ISO 20401:2017(E)ii ISO 2017 All rights reservedCOPYRIGHT PROTECTED DOCUME

10、NT ISO 2017, Published in SwitzerlandAll rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written pe

11、rmission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCh. de Blandonnet 8 CP 401CH-1214 Vernier, Geneva, SwitzerlandTel. +41 22 749 01 11Fax +41 22 749 09 47copyrightiso.orgwww.iso.orgISO 20401:2017(E)Forewo

12、rd ivIntroduction v1 Scope .12 Normative references 13 Terms and definitions .14 Integral connectors for plug-in proximity switches 25 Graphical symbols .26 Electrical contacts (pin allocation) .26.1 Identification 26.2 Pin allocation for valves with a single solenoid 36.3 Pin allocation for valves

13、with double solenoids and one connector . 36.4 Pin allocation for valves with double solenoids and two connectors 3Bibliography 5 ISO 2017 All rights reserved iiiContents PageBS ISO 20401:2017ISO 20401:2017(E)ForewordISO (the International Organization for Standardization) is a worldwide federation

14、of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. I

15、nternational organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those

16、intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see

17、 www .iso .org/ directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the doc

18、ument will be in the Introduction and/or on the ISO list of patent declarations received (see www .iso .org/ patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the voluntary nature of standards,

19、 the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www .iso .org/ iso/ foreword .html.This document was prepa

20、red by Technical Committee ISO/TC 131, Fluid power systems, Subcommittee SC 5, Control products and components.This second edition cancels and replaces the first edition (ISO 20401:2005), which has been technically revised. It also incorporates the Technical Corrigendum ISO 20401:2005/Cor1: 2005.iv

21、ISO 2017 All rights reservedBS ISO 20401:2017ISO 20401:2017(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical commi

22、ttees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the I

23、nternational Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the

24、different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. I

25、SO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www .iso .org/ patents).Any trade name used in this d

26、ocument is information given for the convenience of users and does not constitute an endorsement.For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the World Trade

27、 Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www .iso .org/ iso/ foreword .html.This document was prepared by Technical Committee ISO/TC 131, Fluid power systems, Subcommittee SC 5, Control products and components.This second edition cancels and repl

28、aces the first edition (ISO 20401:2005), which has been technically revised. It also incorporates the Technical Corrigendum ISO 20401:2005/Cor1: 2005.iv ISO 2017 All rights reserved ISO 20401:2017(E)IntroductionIn pneumatic fluid power systems, power is transmitted and controlled through a fluid und

29、er pressure within an enclosed circuit. Typical components found in such systems are pneumatic controls. These devices are used to regulate the function of a component or system.Some control components found in pneumatic fluid power systems are electrically actuated. For small control components wit

30、h electrical control mechanisms, plug connectors of round type with diameters of 8 mm and 12 mm are used. For a unified actuation of the control component in relationship to the electrical power, a standardized pin assignment is required. ISO 2017 All rights reserved vBS ISO 20401:2017BS ISO 20401:2

31、017Pneumatic fluid power systems Directional control valves Specification of pin assignment for 8 mm and 12 mm diameter electrical round connectors1 ScopeThis document specifies the pin assignment for pneumatic directional control valves when used together with 8 mm and 12 mm diameter electrical rou

32、nd connectors according to IEC 60947-5-2. This definition is valid for connectors as shown in IEC 60947-5-2:2004, Figures D.2 and D.4, which are shown in Clause 4.2 Normative referencesThe following documents are referred to in the text in such a way that some or all of their content constitutes req

33、uirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 1219-1, Fluid power systems and components Graphical symbols and circuit diagrams Part 1: Graphical symbols f

34、or conventional use and data-processing applicationsISO 5598, Fluid power systems and components VocabularyISO 11727, Pneumatic fluid power Identification of ports and control mechanisms of control valves and other componentsIEC 60947-5-2:2004, Low-voltage switchgear and controlgear Part 5-2: Contro

35、l circuit devices and switching elements Proximity switches3 Terms and definitionsFor the purposes of this document, the terms and definitions given in ISO 5598 apply.ISO and IEC maintain terminological databases for use in standardization at the following addresses: IEC Electropedia: available at h

36、 t t p :/ www .electropedia .org/ ISO Online browsing platform: available at h t t p :/ www .iso .org/ obpINTERNATIONAL STANDARD ISO 20401:2017(E) ISO 2017 All rights reserved 1BS ISO 20401:2017ISO 20401:2017(E)4 Integral connectors for plug-in proximity switchesKey1 pin 1 3 pin 32 pin 2 4 pin 4Figu

37、re 1 12-mm diameter, five-pin connector (pin 5, not shown, is unassigned), male face viewKey1 pin 1 3 pin 32 pin 2 4 pin 4Figure 2 8-mm diameter, four-pin connector, male face view5 Graphical symbolsGraphical symbols used in Figures 3, 4 and 5 are in accordance with ISO 1219-1.6 Electrical contacts

38、(pin allocation)6.1 IdentificationFor identification of ports and control mechanisms of pneumatic directional control valves, ISO 11727 shall be used.2 ISO 2017 All rights reservedBS ISO 20401:2017ISO 20401:2017(E)4 Integral connectors for plug-in proximity switchesKey1 pin 1 3 pin 32 pin 2 4 pin 4F

39、igure 1 12-mm diameter, five-pin connector (pin 5, not shown, is unassigned), male face viewKey1 pin 1 3 pin 32 pin 2 4 pin 4Figure 2 8-mm diameter, four-pin connector, male face view5 Graphical symbolsGraphical symbols used in Figures 3, 4 and 5 are in accordance with ISO 1219-1.6 Electrical contac

40、ts (pin allocation)6.1 IdentificationFor identification of ports and control mechanisms of pneumatic directional control valves, ISO 11727 shall be used.2 ISO 2017 All rights reserved ISO 20401:2017(E)6.2 Pin allocation for valves with a single solenoidThe pin allocation for valves with a single sol

41、enoid is shown in Figure 3. Pin 1: not used Pin 2: not used Pin 3: 0 V for solenoid Pin 4: UB for solenoidFigure 3 Pin allocation for valves with a single solenoid6.3 Pin allocation for valves with double solenoids and one connectorThe pin allocation for valves with double solenoids and one connecto

42、r is shown in Figure 4. Pin 1: not used Pin 2: UB for solenoid 12 Pin 3: 0 V for solenoids Pin 4: UB for solenoid 14Figure 4 Pin allocation for valves with double solenoids and one connector6.4 Pin allocation for valves with double solenoids and two connectorsThe pin allocation for valves with doubl

43、e solenoids and two connectors is shown in Figure 5.For both connectors: Pin 1: not used Pin 2: not used Pin 3: 0 V for solenoid Pin 4: UB for solenoid ISO 2017 All rights reserved 3BS ISO 20401:2017ISO 20401:2017(E)Figure 5 Pin allocation for valves with double solenoids and two connectors4 ISO 201

44、7 All rights reservedBS ISO 20401:2017ISO 20401:2017(E)Figure 5 Pin allocation for valves with double solenoids and two connectors4 ISO 2017 All rights reserved ISO 20401:2017(E)Bibliography1 ISO 5599-1:2001, Pneumatic fluid power Five-port directional control valves Part 1: Mounting interface surfa

45、ces without electrical connector2 ISO 15407-1:2000, Pneumatic fluid power Five-port directional control valves, sizes 18 mm and 26 mm Part 1: Mounting interface surfaces without electrical connector ISO 2017 All rights reserved 5BS ISO 20401:2017ISO 20401:2017(E) ISO 2017 All rights reservedICS 23.1

46、00.50Price based on 5 pagesBS ISO 20401:2017This page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization produ

47、cts are published by BSI Standards Limited.British Standards Institution (BSI)About usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been c

48、arefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find

49、 out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Deve