BS ISO 20087-2016 Photography Digital still cameras Battery life measurement《摄影 静物数码照相机 电池寿命测量》.pdf

《BS ISO 20087-2016 Photography Digital still cameras Battery life measurement《摄影 静物数码照相机 电池寿命测量》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 20087-2016 Photography Digital still cameras Battery life measurement《摄影 静物数码照相机 电池寿命测量》.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、BS ISO 20087:2016Photography Digitalstill cameras Battery lifemeasurementBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS ISO 20087:2016 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 20087:2016.The UK participation in its pr

2、eparation was entrusted to TechnicalCommittee CPW/42, Photography.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication.

3、 The British Standards Institution 2016. Published by BSI StandardsLimited 2016ISBN 978 0 580 89749 8ICS 37.040.99Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 3

4、1 May 2016.Amendments issued since publicationDate Text affectedBS ISO 20087:2016 ISO 2016Photography Digital still cameras Battery life measurementPhotographie Camras numriques Mesurage de la dure de vie de la batterieINTERNATIONAL STANDARDISO20087First edition2016-05-01Reference numberISO 20087:20

5、16(E)BS ISO 20087:2016ISO 20087:2016(E)ii ISO 2016 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2016, Published in SwitzerlandAll rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechani

6、cal, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCh. de Blandonnet 8 CP 401CH-1214 Vernier, Geneva, Switze

7、rlandTel. +41 22 749 01 11Fax +41 22 749 09 47copyrightiso.orgwww.iso.orgBS ISO 20087:2016ISO 20087:2016(E)Foreword ivIntroduction v1 Scope . 12 Terms and definitions . 13 Measurement method . 13.1 General . 13.2 Battery 13.3 Recording media 23.4 Camera settings 23.4.1 Image quality mode . 23.4.2 Nu

8、mber of recorded pixels 23.5 Measurement conditions 23.5.1 Subject distance 23.5.2 Subject to be shot and brightness . 23.5.3 Operating environment 23.6 Required actions 23.6.1 Flash usage 23.6.2 Motor driven optical zoom operation 23.6.3 Picture monitor mode . 23.6.4 Handling when the recording med

9、ium is full 33.6.5 Handling of playback mode 33.6.6 Shooting intervals . 33.6.7 Power off . 33.7 End-of-test criteria 33.8 Measurement flowchart 34 Reporting the results of battery life . 54.1 General rule . 54.2 Battery 54.3 Recording media 54.4 Function-setting and shooting mode . 5Annex A (inform

10、ative) Example description 6Annex B (normative) Additional information 7Bibliography 9 ISO 2016 All rights reserved iiiContents PageBS ISO 20087:2016ISO 20087:2016(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bo

11、dies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental an

12、d non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are de

13、scribed in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn

14、 to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on th

15、e ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment,

16、 as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information.The committee responsible for this document is ISO/TC 42, Photography.iv ISO 2016 All rights reservedBS ISO 20087:2016ISO 20087:2016

17、(E)IntroductionFor digital cameras, long battery life is one of the important features. The Camera and Imaging Products Association (CIPA) defined a CIPA standard “Procedure for Measuring Digital Still Camera Battery Consumption” for specifying a standard measurement procedure. The procedure gives u

18、seful information on battery life to end-users for making a selection from a variety of digital cameras.This International Standard is based on the CIPA standard mentioned above and it is referenced in the Bibliography. The standardized measurement procedure primarily includes high power-consuming f

19、unctions such as image display on picture monitor, use of flash, and zoom and retractable lens movement. ISO 2016 All rights reserved vBS ISO 20087:2016BS ISO 20087:2016Photography Digital still cameras Battery life measurement1 ScopeThis International Standard specifies measurement method of batter

20、y life for consumer-use digital still cameras (hereinafter referred to as “DSC”).2 Terms and definitionsFor the purposes of this document, the following terms and definitions apply.2.1number of shotsnumber of pictures shot by a digital camera under the conditions stipulated in the measurement proced

21、ure in this International Standard3 Measurement method3.1 Generala) All the still-photography functions shall be utilized to their full extent when the measurement is conducted. The functions which have nothing to do with taking still photography (e.g. audio-recording and movie-recording functions)

22、need not be activated during the measurement.b) The cameras function-setting parameters, except those defined in this International Standard, shall be identical to factory shipping settings. If the measurement is conducted with parameters that are different from the factory shipping settings, such s

23、ettings parameters shall be reported along with the measurement results. If certain setting parameters are not defined by the factory shipping settings (see Annex B), the measurement shall be conducted using the settings which are most likely employed by the users of the applicable cameras, and info

24、rmation which can identify such setting parameters shall be reported along with the measurement data.c) Some of the functions whose test conditions are defined in this International Standard may be ignored if a camera to be measured is not equipped with those functions.d) If the power level is not f

25、ully determined by the factory shipping setting, the measurement shall be made with the operation that result in the highest power demand level for the camera.Summarized priorities for the above a), b) and c) are as follows. The measurement conditions of the standard procedure which are listed in 3.

26、2 to 3.8. Function-setting parameters which are not listed in 3.2 to 3.8 shall be identical to the factory shipping settings. If any parameters cannot be defined by the factory shipping settings, such parameters shall be set to ones which are assumed to be most likely employed by the users of the ap

27、plicable cameras.3.2 Batterya) Battery type is not specified for the measurement, but information that can identify the battery shall be reported along with the measurement results.INTERNATIONAL STANDARD ISO 20087:2016(E) ISO 2016 All rights reserved 1BS ISO 20087:2016ISO 20087:2016(E)b) When using

28、a primary battery, a new battery shall be used. When using a secondary battery (rechargeable battery), the battery shall be fully charged (see Annex B).3.3 Recording mediaNot specified, but information that can identify the recording media shall be reported along with the measurement results.3.4 Cam

29、era settings3.4.1 Image quality modeThe factory shipping mode shall be used.3.4.2 Number of recorded pixelsThe factory shipping mode shall be used.3.5 Measurement conditions3.5.1 Subject distanceNot specified.3.5.2 Subject to be shot and brightnessSubject to be shot is not specified. The subject bri

30、ghtness shall be within the range of the cameras AE system, if automatic exposure (AE) is used.3.5.3 Operating environmentMeasurements shall be made at (23 2) C and relative humidity (50 20) %.3.6 Required actions3.6.1 Flash usageFull flash shall be used for one of every two shots. For the other sho

31、t, the flash shall not be used. Any given shooting condition for the full illumination flash may be used.3.6.2 Motor driven optical zoom operationThe motor driven optical zoom lens shall be moved either from the TELE end to the WIDE end or from the WIDE end to the TELE end before every picture is ta

32、ken. The zoom lens may be moved either as TELE WIDE TELE or as WIDE TELE WIDE with every two shots. Nothing is specified on its movement during the measurement other than the motor-driven optical zoom operation.3.6.3 Picture monitor modea) The picture monitor shall be turned on at all times to be us

33、ed as the electric viewfinder during the measurement. If the picture monitor turns off automatically during the measurement or if it automatically shifts into other display modes, it shall immediately be turned back into the viewfinder mode either by an automatic or manual operation (except replacin

34、g batteries or power cycling) and the test shall be continued. For cameras equipped with two or more picture monitors, the test can be conducted with only the most power consuming one turned on at all times.2 ISO 2016 All rights reservedBS ISO 20087:2016ISO 20087:2016(E)b) If the picture monitor is

35、equipped with an illumination function (e.g. backlight), the illumination shall be lit for the duration of the test. If the brightness or the contrast of the monitor is adjustable, the adjustable parameter shall be set at the factory shipping setting when the measurement is made.NOTE See Annex B.3.6

36、.4 Handling when the recording medium is fullThe files in the medium shall be deleted immediately with the function in the camera or the medium shall be replaced with an empty one. If replacement is to be done, tester shall minimize the influence on the battery life with the replacement. For example

37、, the tester shall replace the medium when the power is off. It is acceptable to delete files or replace the medium before it becomes full.3.6.5 Handling of playback modeNothing is specified regarding the playback mode including automatic playback (the function for displaying images automatically im

38、mediately after they are shot).3.6.6 Shooting intervalsThe first shot shall be made 30 seconds after the power is turned on. During that 30-second period, the flash mode setting, zoom operation and other preparations setting for shooting shall be made. Thereafter, shooting shall be made at a rate of

39、 one picture every 30 seconds. If 30 seconds is not sufficient for initialization, or if the camera is not ready for shooting in 30 seconds after a shot, shooting shall be made immediately when the camera becomes ready.3.6.7 Power offPower shall be turned off after every tenth picture has been shot

40、and processed. The interval before the next power-on shall be enough time not to affect battery life (i.e. so that any additional off time will not change the measurement results).NOTE See Annex B.3.7 End-of-test criteriaThe measurement shall be finished when the first low-battery shutdown occurs or

41、 when any function related to still photography stops working without low-battery shutdown.However, if the function can be reactivated automatically or manually (except replacing batteries or power cycling), the function shall be reactivated immediately and the test shall be continued.NOTE See Annex

42、 B.3.8 Measurement flowchartThe measurement may follow the flowchart in Figure 1. ISO 2016 All rights reserved 3BS ISO 20087:2016ISO 20087:2016(E)The measurement shall end when it meets the End-of-test criteria at any step of the procedure.Figure 1 Measurement flowchart4 ISO 2016 All rights reserved

43、BS ISO 20087:2016ISO 20087:2016(E)4 Reporting the results of battery life4.1 General ruleOnly the number of shots shall be reported as battery life result. However, “battery life” may be replaced with “possible number of shots,” “number of recordable pictures” or “number of shots.”4.2 BatteryInforma

44、tion (at least model name or type) which identifies the kinds of batteries used shall be reported. If the batteries used in the measurement are equivalent to the battery bundled with the camera, the description “Bundled batteries are used” may be used.4.3 Recording mediaInformation (at least model n

45、ames or types) which identifies the kinds of media used shall be reported. If the media bundled with the camera, the description “Bundled media are used” may be used.4.4 Function-setting and shooting modeIf the measurement is made using a function-setting or shooting mode different from the factory

46、shipping setting, such measurement conditions shall be reported, except under the conditions set forth in the stipulations in this International Standard. ISO 2016 All rights reserved 5BS ISO 20087:2016ISO 20087:2016(E)Annex A (informative) Example descriptionA.1 Example 1Number of pictures that can

47、 be shot: XX(Based on the ISO 20087 and using the batteries and memory card bundled with the camera)A.2 Example 2Battery Life: XX pictures (ISO)Recording medium: YY (YY indicates model of medium)Batteries used: AA size Alkaline batteriesA.3 Example 3Battery Life: XX pictures (Based on ISO standard),

48、 YY pictures (Based on manufacturers standard*)Recording medium used: 32 MB ZZ (ZZ indicates model of medium)Batteries used: Made by XX, AA size Nickel-Hydrogen battery* Manufacturers own measurement method: Measurement is based on our own standard: The liquid crystal display is set to “OFF”; other

49、items are the same as the ISO standard.A.4 Example 4Battery Life: XX picturesBatteries (type XYZ) supplied with camera, and separately sold recording media ABCD were used. Shooting was performed with the mode-dial at AUTO.A.5 Example 5Number of shots: XX pictures (Nickel-Hydrogen batteries supplied with the camera)YY pictures (AA size Alkaline battery)Using built-in memory media6 ISO 2016 All rights reservedBS ISO 20087:2016ISO 20087:2016(E)Annex B (normative) Additional informationB.1 GeneralThis Annex giv