BS ISO 19579-2006 Solid mineral fuels - Determination of sulfur by IR spectrometry《固体矿物燃料 红外光谱法测定硫含量》.pdf

《BS ISO 19579-2006 Solid mineral fuels - Determination of sulfur by IR spectrometry《固体矿物燃料 红外光谱法测定硫含量》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 19579-2006 Solid mineral fuels - Determination of sulfur by IR spectrometry《固体矿物燃料 红外光谱法测定硫含量》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、 g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58ICS 73.040; 75.160.10Solid mineral fuels Determination of sulfur by IR spectrometryBRITISH STANDARD

2、BS ISO 19579:2006BS ISO 19579:2006This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 October 2006 BSI 2006ISBN 0 580 49452 7Amendments issued since publicationAmd. No. Date Commentscontract. Users are responsible for its correct application.C

3、ompliance with a British Standard cannot confer immunity from legal obligations.National forewordThis British Standard was published by BSI. It is the UK implementation of ISO 19579:2006. The UK participation in its preparation was entrusted to Technical Committee PTI/16, Solid mineral fuels.A list

4、of organizations represented on PTI/16 can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a Reference numberISO 19579:2006(E)INTERNATIONAL STANDARD ISO19579First edition2006-10-01Solid mineral fuels Determination of sulfur by IR s

5、pectrometry Combustibles minraux solides Dtermination du soufre par spectromtrie infrarouge BS ISO 19579:2006ii iiiContents Page Foreword iv Introduction v 1 Scope . 1 2 Normative references . 1 3 Principle. 1 4 Apparatus 1 5 Reagents 2 6 Preparation of sample 2 7 Procedure 3 8 Calibration check 3 9

6、 Expression of results . 3 10 Precision 3 11 Test report . 4 BS ISO 19579:2006iv Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through

7、 ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborate

8、s closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards

9、. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this

10、 document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 19579 was prepared by Technical Committee ISO/TC 27, Solid mineral fuels, Subcommittee SC 5, Methods of analysis. BS ISO 19579:2006vIntroduction Sulfur is normally pres

11、ent in coal in three forms; inorganic sulfides such as pyrite (FeS2), inorganic sulfates associated with the mineral matter and organic sulfur in the carbonaceous substance. This International Standard describes a high-temperature combustion/infrared absorption method of analysis, which is used to d

12、etermine the total sulfur content of coal. BS ISO 19579:2006blank1Solid mineral fuels Determination of sulfur by IR spectrometry 1 Scope This International Standard specifies an alternative method of determining the total sulfur content of hard coal, brown coal, and lignite by high-temperature combu

13、stion and infrared (IR) absorption using commercially available instruments. This method has been shown to be applicable to coal samples having an ash yield of less than 40 %. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated

14、references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 334, Solid mineral fuels Determination of total sulfur Eschka method ISO 351, Solid mineral fuels Determination of total sulfur High temperature c

15、ombustion method ISO 687, Solid mineral fuels Coke Determination of moisture in the general analysis test sample ISO 5068-2, Brown coals and lignites Determination of moisture content Part 2: Indirect gravimetric method for moisture in the analysis sample ISO 11722, Solid mineral fuels Hard coal Det

16、ermination of moisture in the general analysis test sample by drying in nitrogen 3 Principle The coal sample is combusted at 1 350 C in a stream of oxygen. Particulates and water vapour are removed from the gas stream by traps of glass wool and magnesium perchlorate. The gas stream then passes throu

17、gh a cell in which the sulfur dioxide is measured by an infrared absorption detector, connected to a microprocessor. The instrument is calibrated with standard reference materials. The percentage of sulfur in the sample is calculated from this prior calibration by the microprocessor. 4 Apparatus 4.1

18、 Instrument, commercially available, consisting of the following: a) resistance furnace, capable of maintaining a temperature of approximately 1 350 C in the combustion zone; b) combustion tube, of ceramic material, to contain the sample and combustion gases; BS ISO 19579:20062 c) combustion boats,

19、of ceramic material, into which the sample is weighed and then combusted; d) combustion gas-purification train, through which the combustion gases pass from the combustion tube to the detector (the train consists of a glass wool filter and a trap containing anhydrous magnesium perchlorate); e) detec

20、tor/microprocessor, a non-dispersion infrared measurement system. 4.2 Balance, capable of weighing to 1 mg. 5 Reagents 5.1 Magnesium perchlorate, anhydrous granular. 5.2 Oxygen, compressed industrial grade, 99,5 % by volume. 5.3 Glass wool. 5.4 Reference coals or cokes. Certified reference materials

21、 (CRMs) are coal or coke samples of known sulfur concentration analysed in accordance with ISO 334 or ISO 351. The reference materials shall be traceable to an internationally recognized certifying organization. NOTE 1 Calibration with coals or cokes that are similar in composition to the analysis s

22、amples is necessary. It has been noted that some coals containing high levels of carbonates and some low-rank coals containing high levels of carboxylic salts of calcium can require longer combustion/integration times, as the release of sulfur dioxide can be delayed during combustion. If coal or cok

23、e samples (other than CRMs) are used for calibrations, then it is necessary to verify the calibration. This is done by analysing an appropriate CRM after calibration. If the results of the analysis of the CRM do not agree with the certified value of the sulfur content, the instrument should be recal

24、ibrated. NOTE 2 Reference materials including CRMs can contain moisture and are usually certified on a dry basis. It is necessary to determine the moisture content in accordance with ISO 11722, ISO 687 and ISO 5068-2 as appropriate. This moisture is used to calculate the dry-basis sulfur value to an

25、 “as analysed” value, wS,aa, expressed in percent, as given in Equation (1): wS,aa= wS,d,ac (100 wH2O)/100 (1) where wS,d,acis the dry-basis sulfur content, expressed in mass percent; wH2Ois the moisture content, expressed in mass percent. 6 Preparation of sample The coal or coke used for the determ

26、ination of total sulfur content is the analysis sample ground to pass a sieve of 212 m aperture. Expose the sample in a thin layer for the minimum time required for the moisture content to reach approximate equilibrium with the laboratory atmosphere. Before commencing the determination, mix the air-

27、dried sample. After weighing the test portion (see Clause 7), determine the moisture content using a further portion of the test sample by the method described in ISO 11722, ISO 687 or ISO 5068-2, as appropriate. BS ISO 19579:200637 Procedure Prepare the instrument according to the manufacturers ins

28、tructions. It is advisable to process two samples to condition the instrument prior to calibration. Calibrate the instrument using a reference coal or coke sample or reference coal or coke samples if a multi-point calibration is possible. The calibration should cover the range of sulfur concentratio

29、ns below and above that present in the samples. Use the calibration procedure recommended by the instrument manufacturer. Accurately weigh, to 0,001 g, 0,2 g to 0,5 g of the reference coal or coke into the combustion boat and enter the weight into the processor (computer). Push the boat plus sample

30、into the hot zone of the furnace. The combustion products are pumped through the traps to the IR detector, where the absorption signal due to sulfur dioxide is integrated. At completion of the burn (indicated by the instrument), remove the boat containing the combustion residue. NOTE Some instrument

31、s are designed for automatic operation and manual sample introduction and removal is not necessary. Repeat the process with a further two replicates of the reference coal or coke. Check the accuracy of the calibration by analysing the calibrating reference coal or coke and another reference coal or

32、coke of lower sulfur concentration as unknown samples. If the results obtained for the reference coals or cokes are not within the repeatability of the method (see 10.1), repeat the calibration procedure. Determine the sulfur concentration in the sample by the same procedure as used for the referenc

33、e coals or cokes. 8 Calibration check A calibration check shall be completed periodically (it is recommended that this be after every five determinations). A standard of known sulfur content, not necessarily a CRM, shall be analysed. If the result does not agree with the concentration of sulfur in t

34、he standard within the repeatability of the method, the preceding results shall be discarded and the calibration repeated (Clause 7) and the samples reanalysed. 9 Expression of results The sulfur content of the sample as analysed is calculated by the microprocessor and expressed as a mass percent. T

35、he result, the mean of duplicate determinations, shall be reported to the nearest 0,01 mass %. 10 Precision 10.1 Repeatability The results of duplicate determinations carried out at different times in the same laboratory, by the same operator, with the same apparatus, on representative portions take

36、n from the same analysis sample, shall not differ by more than the value of the repeatability, r, as given by Equation (2): r = 0,02 + 0,03 x (2) where x is the mean of the intra-laboratory results. BS ISO 19579:20064 10.2 Reproducibility The means of the results of duplicate determinations, carried

37、 out in each of two laboratories, on representative portions taken from the same sample after the last stage of sample preparation, shall not differ by more than the value of the reproducibility, R, as given by Equation (3): R = 0,02 + 0,09 x (3) where x is the mean of the inter-laboratory results.

38、11 Test report The test report shall include the following particulars: a) identification of the sample tested; b) reference to the method used; c) results and the method of expression used; d) moisture content, if result is reported on an air-dried (as-received) basis. BS ISO 19579:2006blankBS ISO

39、BSI389 Chiswick High RoadLondonW4 4AL19579:2006BSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standa

40、rds are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using t

41、his British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automa

42、tically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at

43、http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and internatio

44、nal standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subsc

45、ribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information

46、 regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the i

47、nternational standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI.

48、This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.