BS ISO 19095-1-2015 Plastics Evaluation of the adhesion interface performance in plastic-metal assemblies Guidelines for the approach《塑料 塑料金属配件中粘结界面性能的评价 方法指南》.pdf

《BS ISO 19095-1-2015 Plastics Evaluation of the adhesion interface performance in plastic-metal assemblies Guidelines for the approach《塑料 塑料金属配件中粘结界面性能的评价 方法指南》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 19095-1-2015 Plastics Evaluation of the adhesion interface performance in plastic-metal assemblies Guidelines for the approach《塑料 塑料金属配件中粘结界面性能的评价 方法指南》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS ISO 19095-1:2015Plastics Evaluation ofthe adhesion interfaceperformance in plastic-metalassembliesPart 1: Guidelines for the approachBS ISO 19095-1:2015 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 19095-1:2015.The UK participatio

2、n in its preparation was entrusted to TechnicalCommittee PRI/52, Adhesives.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapp

3、lication. The British Standards Institution 2015. Published by BSI StandardsLimited 2015ISBN 978 0 580 85345 6ICS 83.180Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committe

4、e on 31 August 2015.Amendments issued since publicationDate Text affectedBS ISO 19095-1:2015 ISO 2015Plastics Evaluation of the adhesion interface performance in plastic-metal assemblies Part 1: Guidelines for the approachPlastiques valuation des performances de linterface dadhrence dans les assembl

5、ages plastique-mtal Partie 1: Lignes directrices pour lapprocheINTERNATIONAL STANDARDISO19095-1First edition2015-08-01Reference numberISO 19095-1:2015(E)BS ISO 19095-1:2015ISO 19095-1:2015(E)ii ISO 2015 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2015, Published in SwitzerlandAll rights rese

6、rved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either IS

7、O at the address below or ISOs member body in the country of the requester.ISO copyright officeCh. de Blandonnet 8 CP 401CH-1214 Vernier, Geneva, SwitzerlandTel. +41 22 749 01 11Fax +41 22 749 09 47copyrightiso.orgwww.iso.orgBS ISO 19095-1:2015ISO 19095-1:2015(E)Foreword ivIntroduction v1 Scope . 12

8、 Normative references 13 Terms and definitions . 14 Conditioning 25 Apparatus . 26 Test procedures . 36.1 Test specimens for the evaluation 36.2 Adhesion interface performance . 36.3 Environmental tests . 3 ISO 2015 All rights reserved iiiContents PageBS ISO 19095-1:2015ISO 19095-1:2015(E)ForewordIS

9、O (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical co

10、mmittee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electro

11、technical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was draf

12、ted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent ri

13、ghts. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and does not const

14、itute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary informationThe com

15、mittee responsible for this document is ISO/TC 61, Plastics, Subcommittee SC 11, Products.ISO 19095 consists of the following parts, under the general title Plastics Evaluation of the adhesion interface performance in plastic-metal assemblies: Part 1: Guidelines for the approach Part 2: Test specime

16、ns Part 3: Test methods Part 4: Environmental conditions for durabilityiv ISO 2015 All rights reservedBS ISO 19095-1:2015ISO 19095-1:2015(E)IntroductionStructures of heterogeneous materials are being manufactured in the automobiles and aerospace industry sectors where higher safety margins are requi

17、red.The existing test methods are not appropriate because the evaluation of the plastic-metal interface performance is difficult as the polymer material has a relatively low mechanical strength and therefore fractures outside the joints. Therefore, it is necessary to develop a methodology for the ev

18、aluation of the plastic-metal interface performance.A test method to evaluate accurately the adhesion interface performance or standardization of long-term evaluation under harsh environments is also necessary.The method in ISO 19095 is intended to ensure the integrity of the interface is realized t

19、hrough the interface and that traceability of the value improves the data comparison.This part of ISO 19095 provides guidelines for the evaluation methods of the adhesion interface performance in plastic-metal structures. ISO 2015 All rights reserved vBS ISO 19095-1:2015BS ISO 19095-1:2015Plastics E

20、valuation of the adhesion interface performance in plastic-metal assemblies Part 1: Guidelines for the approachSAFETY STATEMENT Persons using this part of ISO 19095 should be familiar with normal laboratory practice, if applicable. This part of ISO 19095 does not purport to address all of the safety

21、 problems, if any, associated with its use. It is the responsibility of the user to establish appropriate safety and health practices and to ensure compliance with any regulatory conditions. It is recognized that some of the materials permitted in this part of ISO 19095 might have a negative environ

22、mental impact. As technological advances lead to more acceptable alternatives for such materials, they will be eliminated to the greatest extent possible. At the end of the test, care should be taken to dispose of all waste in an appropriate manner in accordance with local regulations.1 ScopeThis pa

23、rt of ISO 19095 specifies the evaluation methods for the adhesion interface performance in plastic-metal assemblies.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only th

24、e edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 291, Plastics Standard atmospheres for conditioning and testingISO 472, Plastics VocabularyISO 3530, Vacuum technology Mass-spectrometer-type leak-detector calibratio

25、nISO 19095-2, Plastics Evaluation of the adhesion interface performance in plastic-metal assemblies Part 2: Test specimensISO 19095-3, Plastics Evaluation of the adhesion interface performance in plastic-metal assemblies Part 3: Test methodsISO 19095-4, Plastics Evaluation of the adhesion interface

26、performance in plastic-metal assemblies Part 4: Environmental condition for durabilityIEC 60068-2-11, Basic environmental testing procedures Part 2-11: Tests Test Ka: Salt mistIEC 60068-2-67, Environmental testing Part 2-67: Tests Test Cy: Damp heat, steady state, accelerated test primarily intended

27、 for components3 Terms and definitionsFor the purposes of this document, the terms and definitions given in ISO 472 and the following apply.INTERNATIONAL STANDARD ISO 19095-1:2015(E) ISO 2015 All rights reserved 1BS ISO 19095-1:2015ISO 19095-1:2015(E)3.1adhesion interface performanceoverall performa

28、nce of the joint between two different materialsEXAMPLE The mechanical strength, air tightness, and sealing properties of the bond.4 ConditioningThe test specimen shall be conditioned as specified in the appropriate standard for the material concerned. In the absence of this information, the most ap

29、propriate set of conditions from ISO 291 shall be selected and the conditioning time is at least 16 h, unless otherwise agreed upon by the interested parties, for example, for testing at elevated or low temperatures.5 Apparatus5.1 Sealing testing machine5.1.1 Helium leak detectorThis is the mass spe

30、ctrometer-type leak detector using the helium gas as a tracer, in which the vacuum exhaust system for keeping the mass spectrometer in operational vacuum condition (5,0 104MPa) is built-in and is calibrated in accordance with ISO 3530.5.1.2 Exhaust systemThis system consists of a vacuum pump for eva

31、cuating the test specimen, vacuum gauge, etc.5.1.3 OthersThe following are used as the accessory for helium leak testing:a) helium gas cylinder for supplying the tracer gas;b) compressor and pressure reducing valve;c) various kinds of joint and piping for assembling of vacuum system and pressurizing

32、 system;d) pressure gauge for measurement of the pressure of test specimen;e) vacuum gauge for measurement of the pressure of test specimen.5.2 Thermal shock testing machineTwo separate chambers or one chamber with rapid change of temperature may be used. If two chambers are used, one for the low te

33、mperature and the other for the high temperature, the location shall be such as to allow transfer of the specimen from one chamber to the other within the prescribed time. Either manual or automatic transfer methods may be used.The chambers shall be capable of maintaining the atmosphere at the appro

34、priate temperature for the test in any region where the specimen is placed.After insertion of the test specimens, the air temperature shall be within the specified tolerance after a time of not more than 10 % of the exposure time.5.3 High temperature high humidity test chamberA test chamber made of

35、materials that are not corrosive. The detailed structure in the test chamber shall be governed by IEC 60068-2-67, Clause 3.2 ISO 2015 All rights reservedBS ISO 19095-1:2015ISO 19095-1:2015(E)5.4 Salt spray test chamberA test chamber made of materials that do not affect corrosion strength of the salt

36、 mist may be used. The detailed structure in the test chamber and method of generating the salt mist shall be governed by IEC 60068-2-11, Clause 3.5.5 Fatigue test machineFatigue test machine which enables sinusoidal fatigue stress cycles to be obtained with the maximum stress in between 10 % and 80

37、 % of the scale range may be used. The machine has a self centering device for attachment of the specimen. The device shall be designed in such a way that its various components move in perfect alignment with the specimen as soon as the specimen is subjected to stress.6 Test procedures6.1 Test speci

38、mens for the evaluationSpecimens for tests are in accordance with ISO 19095-2.6.2 Adhesion interface performanceSpecimens for tests are in accordance with ISO 19095-2. Test conditions are in accordance with ISO 19095-3. Adhesion interface properties are listed as follows:a) tensile strength;b) tensi

39、le shear strength;c) peel strength;d) bending strength;e) impact strength;f) sealing properties.6.3 Environmental testsTest conditions are in accordance with ISO 19095-4. Environmental test methods are listed as follows:a) temperature dependence test;b) thermal shock test;c) temperature/humidity cyc

40、lic test;d) high temperature and high humidity test;e) salt mist test;f) fatigue test. ISO 2015 All rights reserved 3BS ISO 19095-1:2015ISO 19095-1:2015(E) ISO 2015 All rights reservedICS 83.180Price based on 3 pagesThis page deliberately left blankBSI is the national body responsible for preparing

41、British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road Londo

42、n W4 4AL UKAbout usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our o

43、pen consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or co

44、ntacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreig

45、n standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to British Standards On

46、line (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchas

47、e price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about bec

48、oming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure yo

49、ur documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.CopyrightAll the data,