BS ISO 19072-1-2014 Road vehicles Connection interface for pyrotechnic devices two-way and three-way connections Pocket interface definition《道路车辆 点火装置、两通和三通连接接口 袋形接口定义》.pdf

《BS ISO 19072-1-2014 Road vehicles Connection interface for pyrotechnic devices two-way and three-way connections Pocket interface definition《道路车辆 点火装置、两通和三通连接接口 袋形接口定义》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 19072-1-2014 Road vehicles Connection interface for pyrotechnic devices two-way and three-way connections Pocket interface definition《道路车辆 点火装置、两通和三通连接接口 袋形接口定义》.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS ISO 19072-1:2014Road vehicles Connectioninterface for pyrotechnicdevices, two-way and three-way connectionsPart 1: Pocket interface definitionBS ISO 19072-1:2014 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 19072-1:2014.It superse

2、des BS ISO 19072-1:2007 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee AUE/16, Electrical and electronic equipment.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to inc

3、lude all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2014. Published by BSI StandardsLimited 2014ISBN 978 0 580 79264 9ICS 43.040.10Compliance with a British Standard cannot confer immunity fromlegal obligations.This Brit

4、ish Standard was published under the authority of theStandards Policy and Strategy Committee on 30 September 2014.Amendments issued since publicationDate Text affectedBS ISO 19072-1:2014 ISO 2014Road vehicles Connection interface for pyrotechnic devices, two-way and three-way connections Part 1: Poc

5、ket interface definitionVhicules routiers Interface de raccordement pour dispositifs pyrotechniques, deux voies et trois voies Partie 1: Dfinition de linterface du support allumeurINTERNATIONAL STANDARDISO19072-1Second edition2014-06-15Reference numberISO 19072-1:2014(E)BS ISO 19072-1:2014ISO 19072-

6、1:2014(E)ii ISO 2014 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2014All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet

7、or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.or

8、gPublished in SwitzerlandBS ISO 19072-1:2014ISO 19072-1:2014(E) ISO 2014 All rights reserved iiiContents PageForeword ivIntroduction v1 Scope . 12 Normative references 13 Terms and definitions . 14 Dimensional features Squib holder interface including male contacts . 25 Material characteristics 45.1

9、 Material specifications for male contacts 45.2 Contacts and short circuit areas of the male contacts specifications 4Annex A (normative) Sealed variant . 5Annex B (normative) Variant without retainer of the pyrotechnic device/initiator harness connector assembly . 6Bibliography 7BS ISO 19072-1:2014

10、ISO 19072-1:2014(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a sub

11、ject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (I

12、EC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be

13、noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identify

14、ing any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenienc

15、e of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Sup

16、plementary informationThe committee responsible for this document is ISO/TC 22, Road vehicles, Subcommittee SC 3, Electrical and electronic equipment.This second edition cancels and replaces the first edition (ISO 19072-1:2007), which has been technically revised.ISO 19072 consists of the following

17、parts, under the general title Road vehicles Connection interface for pyrotechnic devices, two way and three way connections: Part 1: Pocket interface definition Part 2: Test methods and general performance requirements Part 3: Pyrotechnic device and harness connector assembly - type 1 Part 4: Pyrot

18、echnic device and harness connector assembly - type 2iv ISO 2014 All rights reservedBS ISO 19072-1:2014ISO 19072-1:2014(E)IntroductionRoad vehicles integrate an increasing number of pyrotechnic devices contributing to occupant safety in vehicles (for example, frontal and side air bag, safety belt pr

19、etensioner, etc.).Various pocket definitions currently exist all over the world. This situation appears difficult to manage for the different equipment makers. The goal of this International Standard is to define a common specification.A sealed option of the pyrotechnic device/initiator harness conn

20、ector assembly is also defined. See Annex A.A variant without retainer of the pyrotechnic device/initiator harness connector assembly is also defined. See Annex B.The International Organization for Standardization (ISO) draws attention to the fact that it is claimed that compliance with this documen

21、t may involve the use of a patents DE19939407, EP-B-1079474 and US-A-6,402,640.ISO takes no position concerning the evidence, validity and scope of this patent right.The holder of this patent right has assured ISO that he/she is willing to negotiate licences either free of charge or under reasonable

22、 and non-discriminatory terms and conditions with applicants throughout the world. In this respect, the statement of the holder of this patent right is registered with ISO. Information may be obtained from:FCI145, rue Yves Le-Coz78000 VersaillesFranceAttention is drawn to the possibility that some o

23、f the elements of this document may be the subject of patent rights other than those identified above. ISO shall not be held responsible for identifying any or all such patent rights.ISO (www.iso.org/patents) maintains an on-line database of patents relevant to its standards. Users are encouraged to

24、 consult the database for the most up to date information concerning patents. ISO 2014 All rights reserved vBS ISO 19072-1:2014BS ISO 19072-1:2014Road vehicles Connection interface for pyrotechnic devices, two-way and three-way connections Part 1: Pocket interface definition1 ScopeThe purpose of thi

25、s part of ISO 19072 is to define the minimum specification of the pyrotechnic device pocket interface.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cite

26、d applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ASTM B488: Standard Specification for Electrodeposited Coatings of Gold for Engineering UsesASTM B735: Standard Test Method for Porosity in Gold Coatings on Metal Substrates by Nitric

27、Acid Vapor3 Terms and definitionsFor the purposes of this document, the following terms and definitions apply.3.1connectorassembly used to connect several conductors together or a single conductor to an applianceNote 1 to entry: A male (female) connector is a housing containing male (female) contact

28、s and accessory items. A male connector may be permanently fixed to a wiring harness or to an appliance an electronic control unit (ECU) for example. A female connector is generally permanently fixed to a wiring harness.3.2female contactcontact (including means for cable attachment) designed for ele

29、ctrical engagement on its inner surface, and to accept entry of a male contact, thus forming an electrical connectionSOURCE: ISO 8092-2:2005, 3.63.3housingconnector without its contacts3.4initiatorpart of the pyrotechnical device with two male contactsINTERNATIONAL STANDARD ISO 19072-1:2014(E) ISO 2

30、014 All rights reserved 1BS ISO 19072-1:2014ISO 19072-1:2014(E)3.5male contactcontact (including means for cable attachment) designed for electrical engagement on its outer surface and to enter a female contact, thus forming an electrical connectionSOURCE: ISO 8092-2:2005, 3.53.6pocketsquib holder i

31、nner interface including male contacts3.7retainerring holding an optional shorting clip (shunt) and providing coding and electrical insulation, generally made of plasticNote 1 to entry: The shorting clip (shunt) may be omitted by decision between manufacturer and supplier.3.8shorting clip (shunt)met

32、allic bar of the retainer providing the electrical connection between two male contacts3.9squib holderpart of the pyrotechnic device, holding the initiator and the retainer4 Dimensional features Squib holder interface including male contactsThe contact and short-circuit areas when male and female co

33、nnectors are mated shall comply with Figure 1.2 ISO 2014 All rights reservedBS ISO 19072-1:2014ISO 19072-1:2014(E)Dimensions in millimetresKey1 squib holder2 area in which any shape is acceptable3 minimum plating contact and short-circuit areas according to 5.2; plating shall extend to the tip of th

34、e pin4 any shape accepted; surface of initiator shall be flush with or below datum B but shall meet the connector / retainer function requirement5 any convex or straight shape inside shaded area accepted at top of pin shall be smooth and burr free6 maximum contact point; the female contact shall gua

35、rantee a minimum overlap of 1 mm in the contact area7 rounded and burr free8 undercut geometry required to hold the connector and retainer inside the squib holder; the undercut surface does not need to be a continuous 360 surface and shall meet the specified connector and retainer retention requirem

36、ents and dimensions regardless of material9for existing tools to produce plastic pockets, the following values are also allowed: R 015010, H 635005015,NOTE Datum C depending on the style of the polarization area (hole or slot).Figure 1 Squib holder interface with male contacts ISO 2014 All rights re

37、served 3BS ISO 19072-1:2014ISO 19072-1:2014(E)5 Material characteristics5.1 Material specifications for male contactsThe male contacts shall be manufactured of solid material (not folded or hollow).5.2 Contacts and short circuit areas of the male contacts specificationsMale contact plating shall com

38、ply with the following characteristics: ASTM B488, type (coating purity) and class (coating thickness) to be agreed between the customer and the supplier but not less than class 0,5; ASTM B735, porosity max. 2 pores/mm2; under layer material : nickel 1 m.4 ISO 2014 All rights reservedBS ISO 19072-1:

39、2014ISO 19072-1:2014(E)Annex A (normative) Sealed variantAll contents of the main document are applicable for the sealed design, except key 2 of Figure 1 (see also Figure A.1).For sealed connectors, a seal is inserted between the squib holder and the connector. The space to be left free for the seal

40、 shall comply with Figure A.1.Dimensions in millimetresA BKeyA with retainerB without retainer (see Annex B)1 all shapes accepted2 surface reserved for sealing as option3 possible sealing surfaces, selection has to be agreed between customer and supplier4 alternative 45 2 and 0,5 0,1Figure A.1 Seali

41、ng ISO 2014 All rights reserved 5BS ISO 19072-1:2014ISO 19072-1:2014(E)Annex B (normative) Variant without retainer of the pyrotechnic device/initiator harness connector assemblyAll contents of the main document are applicable for the design without retainer.Without retainer, only the anti-rotationa

42、l feature can exceed the squib holder bottom. Initiator and connector shall comply with Figure B.1.Dimensions in millimetres6,4 0,77 20,87 0,2511,1 0,05BA123,236,450,1 A B3,236,452,13R0,35B0,1 AA BKeyA symmetrical optionB assymetrical option1 squib holder as defined in Figure 12 anti-rotational feat

43、ure for symmetrical and asymmetrical optionFigure B.1 Pocket interface with male contacts6 ISO 2014 All rights reservedBS ISO 19072-1:2014ISO 19072-1:2014(E)Bibliography1 ISO 8092-2, Road vehicles Connections for on-board electrical wiring harnesses Part 2: Definitions, test methods and general perf

44、ormance requirements2 ISO 19072-2, Road vehicles Connection interface for pyrotechnic devices, two-way and three-way connections Part 2: Test methods and general performance requirements ISO 2014 All rights reserved 7BS ISO 19072-1:2014ISO 19072-1:2014(E) ISO 2014 All rights reservedICS 43.040.10Pri

45、ce based on 7 pagesThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI

46、Standards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge

47、embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your

48、 organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards

49、, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Onli