BS ISO 19055-2015 Microscopes Minimum requirements for binocular tubes《显微镜 对双目管的最低要求》.pdf

《BS ISO 19055-2015 Microscopes Minimum requirements for binocular tubes《显微镜 对双目管的最低要求》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 19055-2015 Microscopes Minimum requirements for binocular tubes《显微镜 对双目管的最低要求》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS ISO 19055:2015Microscopes Minimumrequirements for binoculartubesBS ISO 19055:2015 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 19055:2015.The UK participation in its preparation was entrusted to TechnicalCommittee CPW/172, Optics

2、and Photonics.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2015. Published b

3、y BSI StandardsLimited 2015ISBN 978 0 580 84940 4ICS 37.020Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 30 September 2015.Amendments issued since publicationDat

4、e Text affectedBS ISO 19055:2015 ISO 2015Microscopes Minimum requirements for binocular tubesMicroscopes Exigences minimales pour tubes binoculairesINTERNATIONAL STANDARDISO19055First edition2015-09-01Reference numberISO 19055:2015(E)BS ISO 19055:2015ISO 19055:2015(E)ii ISO 2015 All rights reservedC

5、OPYRIGHT PROTECTED DOCUMENT ISO 2015, Published in SwitzerlandAll rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet,

6、 without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCh. de Blandonnet 8 CP 401CH-1214 Vernier, Geneva, SwitzerlandTel. +41 22 749 01 11Fax +41 22 749 09 47copyrightiso.orgwww.iso.o

7、rgBS ISO 19055:2015ISO 19055:2015(E)Foreword iv1 Scope . 12 Normative references 13 Terms and definitions . 14 Requirements 2Annex A (normative) Test methods for binocular tubes . 4 ISO 2015 All rights reserved iiiContents PageBS ISO 19055:2015ISO 19055:2015(E)ForewordISO (the International Organiza

8、tion for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established

9、has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The

10、 procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the ed

11、itorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent r

12、ights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an e

13、xplanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary informationThe committee responsible for this d

14、ocument is ISO/TC 172, Optics and photonics, Subcommittee SC 5, Microscopes and endoscopes.iv ISO 2015 All rights reservedBS ISO 19055:2015INTERNATIONAL STANDARD ISO 19055:2015(E)Microscopes Minimum requirements for binocular tubes1 ScopeThis International Standard specifies the minimum requirements

15、 regarding image quality and viewing ergonomics for binocular tubes for compound microscopes when used with eyepieces as specified by the manufacturer. This International Standard makes a distinction between binocular tubes with and without dioptre adjustment.2 Normative referencesThe following docu

16、ments, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 15227:2000, Optics and

17、 optical instruments Microscopes Testing of stereomicroscopes3 Terms and definitionsFor the purposes of this document, the following terms and definitions apply.3.1interpupillary distanceIPDdistance between the exit pupils of the left and right optical system3.2optical axisaxis given by the central

18、ray of the pencil exiting the eyepiece for an object point in the centre of the object plane3.3convergencedescribes the situation when the optical axis for the left and right optical systems meet at a position further away from the eye than the eyepieceNote 1 to entry: Binocular tubes for compound m

19、icroscopes usually have parallel optical axes for the left and right optical systems.3.4imaging rotationorientation of the image with respect to the optical axis as the axis of rotation3.5relative brightnessbrightness of the darker of the two optical systems divided by the brightness of the lighter

20、of the two optical systemsNote 1 to entry: The requirement in Table 3 shall be fulfilled for any state of polarization.Note 2 to entry: It is expressed in percentage (%). ISO 2015 All rights reserved 1BS ISO 19055:2015ISO 19055:2015(E)4 RequirementsThe requirements specified in Tables 1, 2, and 3 ar

21、e the minimum requirements for opto-mechanical and radiation specifications of binocular tubes.Table 1 makes a distinction between tubes for general use and high-performance tubes.NOTE Tubes for general use fulfil the basic criteria for microscopic applications. High-performance tubes provide increa

22、sed viewing ergonomics when used over prolonged time periods.The values shall be met by any individual tube which claims compliance with this International Standard.For the specified minimum adjustment range for IPD, all requirements shall be met.Tubes with dioptre adjustment shall meet the requirem

23、ents in Table 1, 2, and 3.Tubes without dioptre adjustment shall meet the requirements in Table 1 and Table 3.Table 1 Opto-mechanical requirementsCriterionRequirement for general useRequirement for high performance tubesTest methodMinimum adjustment range for IPD 55 mm to 75 mm A.1Indication error o

24、f IPD scale 1 mm A.2Difference in optical axis between left and right optical systems Vertical 15ISO 15227:2000, 6.3.3.1HorizontalConvergence 45Divergence 10 3Difference in centres between left and right imageVertical 0,20 mmA.3HorizontalConvergence0,40 mmDivergenceDifference in axial position betwe

25、en left and right image0,3 mm A.4Difference in imaging rotation between left and right image2ISO 15227:2000, 6.3.5Difference in exit pupil position between left and right optical system1 mm A.52 ISO 2015 All rights reservedBS ISO 19055:2015ISO 19055:2015(E)Table 2 Additional opto-mechanical requirem

26、ents for tubes with dioptre adjustmentCriterion Requirement Test methodMinimum range of dioptre adjustment 5 D to +5 DISO 15227:2000, 6.3.13Difference in axial position between left and right image at 0 D 0,5 mm A.6Table 3 Radiation requirementsCriterion Requirement Test methodRelative brightness 65

27、 % A.7 ISO 2015 All rights reserved 3BS ISO 19055:2015ISO 19055:2015(E)Annex A (normative) Test methods for binocular tubesA.1 Minimum adjustment range for IPDThe IPD shall be measured as the distance of the centres of the exit pupils of the two eyepieces.A.2 Indication error of IPD scaleThe indicat

28、ion error is the difference between the quantity measured in A.1 and the marked IPDs on the binocular tube.A.3 Difference in centres between left and right imageA reference eyepiece with crosshairs is inserted into the left eyepiece sleeve and a specimen with crosshairs is focused. The specimen is l

29、aterally adjusted so the crosshairs of the eyepiece and the specimen are aligned.The reference eyepiece is then inserted into the right sleeve and the distance between the eyepiece crosshairs and the specimen crosshairs in vertical and horizontal direction is measured.A.4 Difference in axial positio

30、n between left and right imageA focusable reference eyepiece set to its nominal focus position is inserted in the left eyepiece sleeve and a specimen is focused.The reference eyepiece is then inserted into the right sleeve. The eyepiece is axially adjusted until the specimen is focused and the resul

31、ting axial adjustment is measured.A.5 Difference in exit pupil position between left and right optical systemThe exit pupil position shall be measured perpendicular to the surface defined by the eyepiece location flange of the left optical system.For tubes with dioptre adjustment, this quantity shal

32、l be measured at 0 D at the dioptre scale.A.6 Difference in axial position between left and right image at 0 DThe eyepiece sleeve with dioptre adjustment is set to 0 D and the same measurement as in A.4 is performed.A.7 Relative brightnessThe brightness shall be measured with a light source of type

33、D65 located in the nominal entrance pupil of the tube. The light source shall be of circular shape and be at least 8 mm in diameter. The measurements shall be carried out in the exit pupils of the eyepieces.4 ISO 2015 All rights reservedBS ISO 19055:2015BS ISO 19055:2015ISO 19055:2015(E) ISO 2015 Al

34、l rights reservedICS 37.020Price based on 4 pagesThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization

35、products are published by BSI Standards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -

36、based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide yo

37、u with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted Europe

38、an and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.SubscriptionsOur range of subscription services

39、are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed da

40、ily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Membe

41、rs. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your in

42、tranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendment or revision. We continually

43、 improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.CopyrightAll the data, software and documentation set out in all British Standards and other BSI pu

44、blications are the property of and copyrighted by BSI, or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use. Except as permitted under the Copyright

45、, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. Details and advice can be obtained from the Copyright & Licensing Department.Useful Contacts:Customer ServicesTel: +44 845 086 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 845 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW