BS ISO 19012-2-2013 Microscopes Designation of microscope objectives Chromatic correction《显微镜 显微镜物镜名称 色彩校正》.pdf

《BS ISO 19012-2-2013 Microscopes Designation of microscope objectives Chromatic correction《显微镜 显微镜物镜名称 色彩校正》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 19012-2-2013 Microscopes Designation of microscope objectives Chromatic correction《显微镜 显微镜物镜名称 色彩校正》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS ISO 19012-2:2013Microscopes Designation ofmicroscope objectivesPart 2: Chromatic correctionBS ISO 19012-2:2013 BRITISH STANDARDNational forewordThis British Standard is the UK

2、 implementation of ISO 19012-2:2013.It supersedes BS ISO 19012-2:2009 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee CPW/172, Optics and Photonics.A list of organizations represented on this committee can beobtained on request to its secretary.This pub

3、lication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2013.Published by BSI Standards Limited 2013 ISBN 978 0 580 78875 8 ICS 37.020 Compliance with a British Standard cannot confer immunity

4、 fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 28 February 2013. Amendments issued since publicationDate T e x t a f f e c t e dBS ISO 19012-2:2013 ISO 2013Microscopes Designation of microscope objectives Part 2: Chroma

5、tic correctionMicroscopes Dsignation des objectifs de microscope Partie 2: Correction chromatiqueINTERNATIONAL STANDARDISO19012-2Second edition2013-02-01Reference numberISO 19012-2:2013(E)BS ISO 19012-2:2013ISO 19012-2:2013(E)ii ISO 2013 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2013All ri

6、ghts reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from

7、either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 19012-2:2013ISO 19012-2:2013(E) ISO 2013 All rights

8、 reserved iiiContents PageForeword iv1 Scope . 12 Normative references 13 Terms and definitions . 14 Requirements 24.1 Basic criterion for the depth of field. 24.2 Markings . 24.3 Specifications 2Annex A (informative) Depth of field, ob4Bibliography 5BS ISO 19012-2:2013ISO 19012-2:2013(E)ForewordISO

9、 (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical com

10、mittee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrot

11、echnical standardization.International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the membe

12、r bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying

13、 any or all such patent rights.ISO 19012-2 was prepared by Technical Committee ISO/TC 172, Optics and photonics, Subcommittee SC 5, Microscopes and endoscopes.This second edition cancels and replaces the first edition (ISO 19012-2:2009), 4.3.2 of which has been technically revised.ISO 19012 consists

14、 of the following parts, under the general title Microscopes Designation of microscope objectives: Part 1: Flatness of field/Plan Part 2: Chromatic correctionThe following parts are under preparation: Part 3: Spectral transmittanceiv ISO 2013 All rights reservedBS ISO 19012-2:2013INTERNATIONAL STAND

15、ARD ISO 19012-2:2013(E)Microscopes Designation of microscope objectives Part 2: Chromatic correction1 ScopeThis part of ISO 19012 specifies classes of chromatic correction and defines minimum requirements regarding chromatic correction. The defined marking on the component enables the operator to co

16、rrectly use the microscope.The standard application for visual observation refers to the combination of objective and tube lens as specified by the manufacturer. The specifications regarding chromatic correction only refer to axial chromatic aberration.2 Normative referencesThe following referenced

17、documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 10934-1, Optics and optical instruments Vocabulary for microscopy Part

18、1: Light microscopy3 Terms and definitionsFor the purposes of this document, the terms and definitions given in ISO 10934-1 and the following apply.3.1reference wavelengthwavelength of 546,07 nm (e-line)3.2blue wavelengthwavelength of 479,99 nm (F-line)3.3red wavelengthwavelength of 643,85 nm (C-lin

19、e)3.4focusbest focusing point for each wavelength3.5focus differenceaxial separation of foci for different wavelengths ISO 2013 All rights reserved 1BS ISO 19012-2:2013ISO 19012-2:2013(E)4 Requirements4.1 Basic criterion for the depth of fieldFormula (1) applies as the basic criterion for the depth

20、of field:ob=nNA22(1)wheren is the refractive index of medium in object space;NA is the numerical aperture of objective; is the wavelength of the reference wave e-line in micrometers.A table of obdepending on NA can be found in Annex A.4.2 Markings4.2.1 GeneralThe following markings may be used if th

21、e requirements according to 4.3 are met.The indication of this marking does not apply to objective lenses sold before the year 2011.This part of ISO 19012 does not apply to the objectives exclusively used on stereomicroscopes.A mixture of a capital letter and a lowercase letter is allowed in marking

22、.4.2.2 AchromatMarking is not necessary but possible.ACH, ACHRO, ACHROMAT4.2.3 SemiapochromatObjective lenses shall be marked with one of the following three options:a) SEMIAPO, orb) FL, orc) a naming containing the letter sequence FLU.4.2.4 ApochromatAPO4.3 Specifications4.3.1 GeneralThe specificat

23、ions of the “Semiapochromat” and “Apochromat” include the criterion of “Achromat”.2 ISO 2013 All rights reservedBS ISO 19012-2:2013ISO 19012-2:2013(E)4.3.2 AchromatThe absolute value of the focus difference between the red wavelength and the blue wavelength is 2 ob.4.3.3 SemiapochromatThe absolute v

24、alues of the focus differences for the red wavelength and the blue wavelength to the reference wavelength are 2,5 ob.4.3.4 ApochromatThe absolute values of the focus differences for the red wavelength and the blue wavelength to the reference wavelength are ob. ISO 2013 All rights reserved 3BS ISO 19

25、012-2:2013ISO 19012-2:2013(E)Annex A (informative) Depth of field, obDry Immersionn 1 n 1,518 (m) 0,546 (m) 0,546NA ob(m) NA ob(m)0,04 170,63 0,40 2,590,07 55,71 0,70 0,850,10 27,30 0,90 0,510,13 16,15 1,00 0,410,15 12,13 1,25 0,270,16 10,66 1,30 0,250,20 6,83 1,35 0,230,22 5,64 1,40 0,210,25 4,370,

26、30 3,030,35 2,230,40 1,710,45 1,350,50 1,090,55 0,900,60 0,760,65 0,650,70 0,560,75 0,490,80 0,430,85 0,380,90 0,340,95 0,304 ISO 2013 All rights reservedBS ISO 19012-2:2013ISO 19012-2:2013(E)Bibliography1 ISO 8578, Microscopes Marking of objectives and eyepieces ISO 2013 All rights reserved 5BS ISO

27、 19012-2:2013ISO 19012-2:2013(E) ISO 2013 All rights reservedICS 37.020Price based on 5 pagesThis page deliberately left blankBSI is the independent national body responsible for preparing British Standards and other standards-related publications, information and services. It presents the UK view o

28、n standards in Europe and at the international level. BSI is incorporated by Royal Charter. British Standards and other standardisation products are published by BSI Standards Limited.British Standards Institution (BSI)raising standards worldwideBSI389 Chiswick High Road London W4 4AL UKTel +44 (0)2

29、0 8996 9001Fax +44 (0)20 8996 Standards and PASs are periodically updated by amendment or revision. Users of British Standards and PASs should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be

30、 grateful if anyone finding an inaccuracy or ambiguity while using British Standards would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside frontcover. Similary for PASs, please notify BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +4

31、4 (0)20 8996 7001BSI offers BSI Subscribing Members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of British Standards and PASs.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy

32、versions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international s

33、tandards, BSI will supply the British Standard implementation of the relevant international standard, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax

34、: +44 (0)20 8996 7005Email: BSI Subscribing Members are kept up to date with standards developments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email:

35、 Information regarding online access to British Standards and PASs via British Standards Online can be found at information about British Standards is available on the BSI website at www.bsi- the data, software and documentation set out in all British Standards and other BSI publications are the p

36、roperty of and copyrighted by BSI, or some person or entity that own copyright in the information used (such as the international standardisation bodies) has formally licensed such information to BSI for commerical publication and use. Except as permitted under the Copyright, Designs and Patents Act

37、 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Department.Tel: +44 (0)20 8996 7070Email: