BS ISO 18695-2007 Textiles - Determination of resistance to water penetration - Impact penetration test《纺织物 防水渗透的测定 渗透作用试验》.pdf

《BS ISO 18695-2007 Textiles - Determination of resistance to water penetration - Impact penetration test《纺织物 防水渗透的测定 渗透作用试验》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 18695-2007 Textiles - Determination of resistance to water penetration - Impact penetration test《纺织物 防水渗透的测定 渗透作用试验》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS ISO 18695:2007Textiles Determination of resistance to water penetration Impact penetration testICS 59.080.01g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g6

2、0g53g44g42g43g55g3g47g36g58BS ISO 18695:2007This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 December 2007 BSI 2007ISBN 978 0 580 53445 4National forewordThis British Standard is the UK implementation of ISO 18695:2007.The UK participation

3、in its preparation was entrusted to Technical Committee TCI/24, Physical testing of textiles.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsibl

4、e for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations. Amendments issued since publicationAmd. No. Date CommentsReference numberISO 18695:2007(E)INTERNATIONAL STANDARD ISO18695First edition2007-11-15Textiles Determination of resistance to wate

5、r penetration Impact penetration test Textiles Dtermination de la rsistance la pntration de leau Essai de pntration par impact BS ISO 18695:2007ii iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work

6、 of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmen

7、tal, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The ma

8、in task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. At

9、tention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 18695 was prepared by Technical Committee ISO/TC 38, Textiles, Subcommittee SC 2, Cleansing, finish

10、ing and water resistance tests. BS ISO 18695:2007blank1Textiles Determination of resistance to water penetration Impact penetration test 1 Scope This International Standard is applicable to any textile fabric, which may or may not have been given a water-resistant or water-repellent finish. It measu

11、res the resistance of fabrics to the penetration of water by low impact, and thus can be used to predict the probable rain penetration resistance of apparel fabrics. The test is best suited for fabrics of medium to loose construction where the Bundesmann rain-shower test (ISO 9865), or Rain Test (IS

12、O 22958) is too severe. Fabrics that do not lie flat under tension are not applicable. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of

13、 the referenced document (including any amendments) applies. ISO 139, Textiles Standard atmospheres for conditioning and testing 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 water resistance characteristic of resisting wetting and penetrat

14、ion by water 4 Principle A volume of water is allowed to spray from a height of (610 10) mm against a taut surface of a test specimen backed by a weighed blotter. The blotter is then reweighed to determine water penetration and the specimen is classified accordingly. 5 Safety Precautions Good labora

15、tory practises should be followed. Wear safety glasses in all laboratory areas. NOTE These safety precautions are for information purposes only. The precautions are ancillary to the testing procedures and are not intended to be all inclusive. It is the users responsibility to use safe and proper tec

16、hniques in handling materials in this International Standard. Manufacturers should be consulted for specific detail such as material safety sheets and other manufacturers recommendations. BS ISO 18695:20072 6 Reagent 6.1 Distilled water or water of equivalent purity, at (27 1) C 7 Apparatus 7.1 Impa

17、ct Penetration Tester1). 7.1.1 Type 1 tester (see Figures 1 and 3). 7.1.2 Type 2 tester (see Figures 2 and 3). 7.2 White textile blotting paper, of (0,71 0,1) mm in thickness, weight of (370 4,5) g/m2, and with an absorbent capacity of (220 30) %2). 7.3 Laboratory balance, accurate to 0,1 g. 8 Condi

18、tioning Condition the test specimens and blotting paper for a minimum of 4 h prior to testing. Conditioning and testing shall be carried out in accordance with ISO 139. 9 Test specimens Cut a minimum of three specimens of (178 10) mm (330 10) mm from the test fabric with the warp in the length direc

19、tion. 10 Procedure 10.1 Clamp one end of the test specimen under the (152 10) mm spring clamp at the top of the inclined stand. Clamp another (152 10) mm clamp, of (0,45 0,05) kg total weight, to the free end of the test specimen. Weigh a standard paper blotter (152 10) mm (229 10) mm to the nearest

20、 0,1 g and insert beneath the specimen. 10.2 Pour (500 10) ml of distilled water (6.1) into the funnel of the tester and allow to spray on to the test specimen. The water should be poured into the funnel without imparting any swirling motion to the water in the funnel. 10.3 Upon completion of the sp

21、raying period (2 s after continuous flow stops), carefully lift the test specimen, remove the blotter, then quickly reweigh to the nearest 0,1 g. 1) Impact Penetration Tester is the name of a suitable product available from AATCC, P O Box 12215, Research Triangle Park, NC 27709-2215 (tel: 1-919-549-

22、8141; fax: 1-919-549-8933; www.aatcc.org). This information is given for the convenience of users of this International Standard and does not constitute an endorsement by ISO of the product named. Equivalent products may be used if they can be shown to lead to the same results. 2) White Textile Blot

23、ting Paper is the trade-name of a product supplied by AATCC, P.O. Box 12215, Research Triangle Park, NC 27709-2215 (tel: 1-919-549-8141; fax: 1-919-549-8933; www.aatcc.org). This information is given for the convenience of users of this International Standard and does not constitute an endorsement b

24、y ISO of the product named. Equivalent products may be used if they can be shown to lead to the same results. BS ISO 18695:2007311 Evaluation The increase in weight of the blotter, in grams, is calculated and the average result for the three test specimens is reported. Individual determinations or a

25、verage values over 5,0 g may be simply reported as + 5,0 g or 5 g. 12 Test report The test report shall include the following information: a) reference to this International Standard, i.e., ISO 18695:2007; b) all information necessary to complete identification of the sample tested; c) the number of

26、 specimens tested; d) the conditioning and testing atmosphere used; e) any deviation from the specified procedure; f) test results. Figure 1 Impact penetration tester Type 1 tester BS ISO 18695:20074 Figure 2 Impact penetration tester Type 2 tester BS ISO 18695:20075Dimensions in millimetres Key 1 l

27、aboratory funnel, 152 mm 2 laboratory ring support 3 metal rod, 12,7 mm 4 rubber tubing, 9,5 mm 5 metal spring clip, 152 mm (494 g) 6 steel plate with clip 7 inclined stand 8 spray head nozzle (see detail A) 9 twenty five holes, (0,99 0,005) mm aBrass. bBronze. Figure 3 Structural details of impact

28、penetration tester BS ISO 18695:20076 Bibliography 1 ISO 9865, Textiles Determination of water repellency of fabrics by the Bundesmann rain-shower test 2 ISO 22958, Textiles Water resistance Rain tests: exposure to a horizontal water spray 3 AATCC Test Method 42 Water Resistance: Impact Penetration

29、Test BS ISO 18695:2007blankBS ISO 18695:2007BSI389 Chiswick High RoadLondonW4 4ALBSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Roy

30、al Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an ina

31、ccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS whi

32、ch ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also

33、available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on

34、 national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)2

35、0 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001.

36、 Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in th

37、e UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without

38、prior written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.