BS ISO 18549-1-2009 Metallic powders - Determination of apparent density and flow rate at elevated temperatures - Determination of apparent density at elevated temperatures《金属粉末 在高.pdf

《BS ISO 18549-1-2009 Metallic powders - Determination of apparent density and flow rate at elevated temperatures - Determination of apparent density at elevated temperatures《金属粉末 在高.pdf》由会员分享，可在线阅读，更多相关《BS ISO 18549-1-2009 Metallic powders - Determination of apparent density and flow rate at elevated temperatures - Determination of apparent density at elevated temperatures《金属粉末 在高.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BS ISO18549-1:2009ICS 77.160NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDMetallic powders Determination ofapparent density andflow rate at elevatedtemperaturesPart 1: Determination of apparentdensity at elevated temperaturesThis British Standardwas published

2、under theauthority of the StandardsPolicy and StrategyCommittee on 31 October2009 BSI 2009ISBN 978 0 580 58096 3Amendments/corrigenda issued since publicationDate CommentsBS ISO 18549-1:2009National forewordThis British Standard is the UK implementation of ISO 18549-1:2009.The UK participation in it

3、s preparation was entrusted to TechnicalCommittee ISE/65, Sintered metal components.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its c

4、orrect application.Compliance with a British Standard cannot confer immunityfrom legal obligations.BS ISO 18549-1:2009Reference numberISO 18549-1:2009(E)ISO 2009INTERNATIONAL STANDARD ISO18549-1First edition2009-04-15Metallic powders Determination of apparent density and flow rate at elevated temper

5、atures Part 1: Determination of apparent density at elevated temperatures Poudres mtalliques Dtermination de la masse volumique apparente et de la vitesse dcoulement tempratures leves Partie 1: Dtermination de la masse volumique apparente tempratures leves BS ISO 18549-1:2009ISO 18549-1:2009(E) PDF

6、disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, part

7、ies accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative

8、to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT

9、PROTECTED DOCUMENT ISO 2009 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or IS

10、Os member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2009 All rights reservedBS ISO 18549-1:2009ISO 18549-1:2009(E) ISO 2009 All righ

11、ts reserved iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subjec

12、t for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC)

13、 on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committee

14、s are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be he

15、ld responsible for identifying any or all such patent rights. ISO 18549-1 was prepared by Technical Committee ISO/TC 119, Powder metallurgy, Subcommittee SC 2, Sampling and testing methods for powders (including powders for hardmetals). ISO 18549 consists of the following parts, under the general ti

16、tle Metallic powders Determination of apparent density and flow rate at elevated temperatures: Part 1: Determination of apparent density at elevated temperatures Part 2: Determination of flow rate at elevated temperatures BS ISO 18549-1:2009BS ISO 18549-1:2009INTERNATIONAL STANDARD ISO 18549-1:2009(

17、E) ISO 2009 All rights reserved 1Metallic powders Determination of apparent density and flow rate at elevated temperatures Part 1: Determination of apparent density at elevated temperatures 1 Scope This part of ISO 18549 describes a method for the determination of apparent density at elevated temper

18、atures for powder mixes, based on iron or steel powders and intended for warm compaction. The method is, to a large extent, based on the apparent density method (funnel method) standardized in ISO 3923-1, but either of the two funnels that are mentioned can be selected after agreement between the pa

19、rties involved. 2 Apparatus 2.1 Thermally insulated enclosure, where the actual measurement shall take place. 2.2 Funnel with an orifice diameter of 2,5 mm or, alternatively, a funnel with an orifice diameter of 5 mm, see Figure 1 or 2, respectively. 2.3 Cylindrical cup, with a capacity of 25 0,03 c

20、m3and an internal diameter of 28 0,5 mm. A cup with the same capacity and with an internal diameter of 30 1 mm is also acceptable. However, 28 0,5 mm is the first option when new equipment is manufactured. The cup and funnel should be made of non-magnetic, corrosion-resistant, metallic material havi

21、ng sufficient wall thickness and hardness to avoid distortion and excessive wear. The inner surfaces of the funnel and cup should be polished. 2.4 Stand and horizontal vibration-free base to support the cup and funnel; the stand holding the orifice of the funnel 25 mm above the top surface of the cu

22、p and coaxially with it, see Figure 3. 2.5 Devices for heating the funnel, e.g. an electrical band heater, and the cylindrical cup, e.g. a cartridge heater, to the selected and agreed temperature for the powder mix within the range 60 C to 180 C, with a maximum allowed variation of 2,5 C. 2.6 Labora

23、tory furnace, for heating the powder sample to the selected and agreed temperature within the range 60 C to 180 C. 2.7 Thermocouples, sufficient to adjust and control the temperatures of the powder mix and the equipment within 2,5 C of the selected temperature. 2.8 Balance, with a capacity of at lea

24、st 200 g, capable of weighing the test sample to an accuracy of 0,01 g. NOTE An example of the insulated enclosure containing the funnel, stand and cup is shown in Figure 4. BS ISO 18549-1:2009ISO 18549-1:2009(E) 2 ISO 2009 All rights reservedDimensions in millimetres Dimensions in millimetresKey 1

25、polished to Ra u 0,4 m athis value is mandatory bD = 0,202,5+Key 1 polished to Ra u 0,4 m athis value is mandatory bD = 0,205+Figure 1 Funnel with orifice diameter of 2,5 mm Figure 2 Funnel with orifice diameter of 5 mm BS ISO 18549-1:2009ISO 18549-1:2009(E) ISO 2009 All rights reserved 3Dimensions

26、in millimetres Key 1 heating device, e.g. band heater 2 heating device aa cup with the same capacity and with an internal diameter of 30 mm 1 mm is also acceptable (see 2.3) Figure 3 Arrangement of the stand with funnel and cup, including heating devices Figure 4 Example of the insulated enclosure c

27、ontaining the funnel, stand and cup BS ISO 18549-1:2009ISO 18549-1:2009(E) 4 ISO 2009 All rights reserved3 Test sample 3.1 The test sample shall have a volume of at least 100 cm3to allow the determination of two or three test portions. 3.2 The test sample shall be heated in the laboratory furnace se

28、t at the selected temperature for the mix in question in the range 60 C to 180 C, to make sure that a homogeneous temperature of the powder can be kept within 2,5 C. 4 Procedure It is recommended to have the balance tared for the empty cylindrical cup before starting the determination. 4.1 Heat the

29、test portion of the mix to the selected target temperature. Carefully load it into the flowmeter funnel as fast as possible to avoid cooling. Allow the powder to flow through the orifice into the density cup. Take care not to move the density cup. 4.2 When the powder completely fills and overflows t

30、he periphery of the density cup, rotate the funnel approximately 90 in a horizontal plane so that the remaining powder in the funnel falls away from the cup. 4.3 Level the powder with the top of the density cup using a non-magnetic spatula or straight-edge held perpendicular to the top of the cup. T

31、ake care to avoid jarring the apparatus at any time. 4.4 After the levelling operation, lightly tap the side of the density cup to settle the powder to avoid spilling the powder when moving the cup. 4.5 Weigh the filled density cup to the nearest 0,01 g. It is very important to minimize heat losses.

32、 Therefore, the heated test portions must be transferred quickly to the thermally insulated enclosure. WARNING Both the powder and equipment are warm. The operation must therefore be carried out with care. 5 Result The mass, in grams, of the powder in the levelled density cup shall be divided by the

33、 volume of the cup (25 cm3). Report the arithmetical mean of the two or three determinations to the nearest 0,01 g/cm3. 6 Test report The test report shall include the following information: a) a reference to this part of ISO 18549; b) all details necessary for the identification of the test sample;

34、 c) the nominal diameter of the orifice; d) the testing temperature used for the powder sample and funnel; e) the result obtained, and how many determinations it is based on; f) all operations not specified in this part of ISO 18549 or regarded as optional. BS ISO 18549-1:2009ISO 18549-1:2009(E) ISO

35、 2009 All rights reserved 5Bibliography 1 ISO 3923-1:2008, Metallic powders Determination of apparent density Part 1: Funnel method BS ISO 18549-1:2009ISO 18549-1:2009(E) ICS 77.160 Price based on 5 pages ISO 2009 All rights reserved BS ISO 18549-1:2009This page has been intentionally left blank BS

36、ISO18549-1:2009BSI GroupHeadquarters 389Chiswick High Road,London, W4 4AL, UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 - British Standards InstitutionBSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at theinternation

37、al level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments oreditions.It is the constant aim of BSI to improve the quality of our products and services.We would be g

38、rateful if anyone finding an inaccuracy or ambiguity while usingthis British Standard would inform the Secretary of the technical committeeresponsible, the identity of which can be found on the inside front cover. Tel:+44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual upd

39、ating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should beaddressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 89967001 Email: You m

40、ay also buy directly using a debit/creditcard from the BSI Shop on the Website http:/ response to orders for international standards, it is BSI policy to supply theBSI implementation of those that have been published as British Standards,unless otherwise requested.Information on standardsBSI provide

41、s a wide range of information on national, European andinternational standards through its Library and its Technical Help to ExportersService. Various BSI electronic information services are also available whichgive details on all its products and services. Contact Information Centre. Tel:+44 (0)20

42、8996 7111 Fax: +44 (0)20 8996 7048 Email: Subscribing members of BSI are kept up to date with standards developmentsand receive substantial discounts on the purchase price of standards. For detailsof these and other benefits contact Membership Administration. Tel: +44 (0)208996 7002 Fax: +44 (0)20 8

43、996 7001 Email: Information regarding online access to British Standards via British StandardsOnline can be found at http:/ information about BSI is available on the BSI website at http:/CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in theUK, of the publications

44、of the international standardization bodies. Except aspermitted under the Copyright, Designs and Patents Act 1988 no extract maybe reproduced, stored in a retrieval system or transmitted in any form or by anymeans electronic, photocopying, recording or otherwise without prior writtenpermission from

45、BSI.This does not preclude the free use, in the course of implementing the standard,of necessary details such as symbols, and size, type or grade designations. Ifthese details are to be used for any other purpose than implementation then theprior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright and Licensing Manager.Tel: +44 (0)20 8996 7070 Email: