BS ISO 1728-2006 Road vehicles - Pneumatic braking connections between motor vehicles and towed vehicles - Interchangeability《道路车辆 电动车和拖车之间的气动制动连接器》.pdf
《BS ISO 1728-2006 Road vehicles - Pneumatic braking connections between motor vehicles and towed vehicles - Interchangeability《道路车辆 电动车和拖车之间的气动制动连接器》.pdf》由会员分享,可在线阅读,更多相关《BS ISO 1728-2006 Road vehicles - Pneumatic braking connections between motor vehicles and towed vehicles - Interchangeability《道路车辆 电动车和拖车之间的气动制动连接器》.pdf(14页珍藏版)》请在麦多课文档分享上搜索。
1、 g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58motor vehicles and towed vehicles Interchangeability ICS 43.040.40Road vehicles Pneumatic braking c
2、onnections between BRITISH STANDARDBS ISO 1728:2006BS ISO 1728:2006This British Standard was published under the authority of the Standards Policy and Strategy Committee on 29 September 2006 BSI 2006ISBN 0 580 49248 6Amendments issued since publicationAmd. No. Date Commentscontract. Users are respon
3、sible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations. National forewordThis British Standard was published by BSI. It is the UK implementation of ISO 1728:2006.The UK participation in its preparation was entrusted to Technical Committee A
4、UE/11, Braking systems.A list of organizations represented on AUE/11 can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a Reference numberISO 1728:2006(E)INTERNATIONAL STANDARD ISO1728Third edition2006-09-01Road vehicles Pneumatic
5、 braking connections between motor vehicles and towed vehicles Interchangeability Vhicules routiers Liaisons de freinage pneumatique entre automobiles et vhicules tracts Interchangeabilit BS ISO 1728:2006ii iiiForeword ISO (the International Organization for Standardization) is a worldwide federatio
6、n of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee.
7、 International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance wi
8、th the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires appro
9、val by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 1728 was prepared by Technical Committe
10、e ISO/TC 22, Road vehicles, Subcommittee SC 2, Braking systems and equipment. This third edition cancels and replaces the second edition (ISO 1728:1980), which has been technically revised. BS ISO 1728:2006blank1Road vehicles Pneumatic braking connections between motor vehicles and towed vehicles In
11、terchangeability 1 Scope This International Standard specifies the requirements which ensure interchangeability of the pneumatic braking connections between motor vehicles and towed vehicles. It concerns vehicle combinations equipped with pneumatic braking systems with two lines: one control line an
12、d one supply line. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 400
13、9, Commercial vehicles Location of electrical and pneumatic connections between towing vehicles and trailers 3 Interchangeability requirements 3.1 Coupling head type The “Palm type” coupling head shall be used. It shall be fitted with an inhibiting device to prevent incorrect coupling (see Figures 1
14、 and 2). The towing vehicle shall be equipped with an automatic device ensuring, without manual operation, the continuity of the pipelines when they are coupled, and their closure on uncoupling. This device shall not affect the interchangeability. The coupling head shall make provision for any type
15、of valve to be fitted to the towing vehicle, provided that the valve can be opened by the standard coupling head on the towed vehicle and that the ability to be coupled with all coupling heads corresponding to this International Standard is not compromized. 3.2 Coupling head dimensions The dimension
16、s of the coupling heads shall be as given in Tables 1 and 2, and shown in Figures 1 and 2. This International Standard specifies only the dimensional details necessary for the coupling. All other dimensions not shown, as well as details of design, are left to the discretion of the manufacturer. 3.3
17、Location of coupling heads and flexible pipe connections The locations of both electrical and pneumatic connections between towing and towed vehicles are specified in ISO 4009. The location of coupling heads and flexible pipe connections on the towing and towed vehicles shall comply with ISO 4009. B
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BSISO17282006ROADVEHICLESPNEUMATICBRAKINGCONNECTIONSBETWEENMOTORVEHICLESANDTOWEDVEHICLESINTERCHANGEABILITY

链接地址:http://www.mydoc123.com/p-585299.html