BS ISO 17165-1-2007 Hydraulic fluid power Hose assemblies Dimensions and requirements《液压传动 软管组件 尺寸规格和要求》.pdf
《BS ISO 17165-1-2007 Hydraulic fluid power Hose assemblies Dimensions and requirements《液压传动 软管组件 尺寸规格和要求》.pdf》由会员分享,可在线阅读,更多相关《BS ISO 17165-1-2007 Hydraulic fluid power Hose assemblies Dimensions and requirements《液压传动 软管组件 尺寸规格和要求》.pdf(34页珍藏版)》请在麦多课文档分享上搜索。
1、BRITISH STANDARDBS ISO 17165-1:2007Hydraulic fluid power Hose assemblies Part 1: Dimensions and requirementsICS 23.040.70g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g4
2、4g42g43g55g3g47g36g58BS ISO 17165-1:2007This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 November 2007 BSI 2007ISBN 978 0 580 54905 2National forewordThis British Standard is the UK implementation of ISO 17165-1:2007.The UK participation in
3、 its preparation was entrusted by Technical Committee MCE/18, Fluid power systems and components, to Panel MCE/18/-/4, Connectors and associated components.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include a
4、ll the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.Amendments issued since publicationAmd. No. Date CommentsReference numberISO 17165-1:2007(E)INTERNATIONAL STANDARD ISO17165-1F
5、irst edition2007-10-15Hydraulic fluid power Hose assemblies Part 1: Dimensions and requirements Transmissions hydrauliques Flexibles de raccordement Partie 1: Dimensions et exigences BS ISO 17165-1:2007ii iiiContents Page Foreword iv Introduction v 1 Scope . 1 2 Normative references . 1 3 Terms and
6、definitions. 2 4 Designation . 3 5 Hose types, nominal inside diameters and maximum working pressures, and correspondence of hose sizes to tube sizes . 5 6 Dimensions of hose and hose fittings 5 7 Overview of hose type, type of hydraulic fluid and temperature range 5 8 Summary of hose fitting end fo
7、rms and key dimensions. 6 9 Requirements for manufacturing instructions for hose assemblies 16 10 Tolerances on hose assembly length and rotational angle . 16 11 Pressure drop of hose assemblies . 16 12 Requirements and tests . 17 13 Marking 17 14 Identification statement (reference to this part of
8、ISO 17165). 17 Annex A (informative) Maximum working pressures of hoses 18 Annex B (informative) Dimensions of steel tubes to be used in combination with hose types listed in Table A.1 20 Annex C (informative) Key dimensions of the hose types covered in ISO 17165-1 21 Bibliography . 23 BS ISO 17165-
9、1:2007iv Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for
10、which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on al
11、l matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are
12、circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held res
13、ponsible for identifying any or all such patent rights. ISO 17165-1 was prepared by Technical Committee ISO/TC 131, Fluid power systems, Subcommittee SC 4, Connectors and similar products and components. ISO 17165 consists of the following parts, under the general title Hydraulic fluid power Hose as
14、semblies: Part 1: Dimensions and requirements Part 2: Recommended practices for hydraulic hose assemblies BS ISO 17165-1:2007vIntroduction In hydraulic fluid power systems, power is transmitted and controlled through a liquid under pressure within an enclosed circuit. Components may be connected thr
15、ough their ports by piping (both connectors and conductors). Hose assemblies make up the flexible part of piping. BS ISO 17165-1:2007blank1Hydraulic fluid power Hose assemblies Part 1: Dimensions and requirements 1 Scope This part of ISO 17165 specifies requirements for hose assemblies that are manu
16、factured from hoses that conform to ISO 3949 and to all parts of ISO 1436, ISO 3862, ISO 4079 and ISO 11237 and hose fittings with elastomeric seals that conform to ISO 12151-1, ISO 12151-2, ISO 12151-3 and ISO 12151-6. This part of ISO 17165 contains information of the most important criteria for t
17、he selection of preferred types of hoses and hose fittings with elastomeric sealing for use in hydraulic fluid power applications. Recommendations for installation, storage, life cycle and the necessary inspections to ensure the full functionality of hose assemblies are given in ISO/TR 17165-2. 2 No
18、rmative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 1436-1, Rubber hoses and h
19、ose assemblies Wire-braid-reinforced hydraulic types Specification Part 1: Oil-based fluid applications ISO 1436-2, Rubber hoses and hose assemblies Wire-braid-reinforced hydraulic types Specification Part 2: Water-based fluid applications ISO 3862-1, Rubber hoses and hose assemblies Rubber-covered
20、spiral-wire-reinforced hydraulic types Specification Part 1: Oil-based fluid applications ISO 3862-2, Rubber hoses and hose assemblies Rubber-covered spiral-wire-reinforced hydraulic types Specification Part 2: Water-based fluid applications ISO 3949, Plastics hoses and hose assemblies Textile-reinf
21、orced types for hydraulic applications Specification ISO 4079-1, Rubber hoses and hose assemblies Textile-reinforced hydraulic types Specification Part 1: Oil-based fluid applications ISO 4079-2, Rubber hoses and hose assemblies Textile-reinforced hydraulic types Specification Part 2: Water-based fl
22、uid applications BS ISO 17165-1:20072 ISO 55981), Fluid power systems and components Vocabulary ISO 6743-4, Lubricants, industrial oils and related products (class L) Classification Part 4: Family H (Hydraulic systems) ISO 8330, Rubber and plastics hoses and hose assemblies Vocabulary ISO 8434-1:200
23、7, Metallic tube connections for fluid power and general use Part 1: 24 cone connections ISO 11237-1, Rubber hoses and hose assemblies Wire-braid-reinforced compact types for hydraulic applications Specification Part 1: Oil-based fluid applications ISO 11237-2, Rubber hoses and hose assemblies Wire-
24、braid-reinforced compact types for hydraulic applications Specification Part 2: Water-based fluid applications ISO 12151-1, Connections for hydraulic fluid power and general use Hose fittings Part 1: Hose fittings with ISO 8434-3 O-ring face seal ends ISO 12151-2, Connections for hydraulic fluid pow
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BSISO1716512007HYDRAULICFLUIDPOWERHOSEASSEMBLIESDIMENSIONSANDREQUIREMENTS 液压 传动 软管 组件 尺寸 规格 要求 PDF

链接地址:http://www.mydoc123.com/p-585260.html