BS ISO 16358-3-2013 Air-cooled air conditioners and air-to-air heat pumps Testing and calculating methods for seasonal performance factors Annual performance factor《气冷式空调和空气热泵 季节性能.pdf

《BS ISO 16358-3-2013 Air-cooled air conditioners and air-to-air heat pumps Testing and calculating methods for seasonal performance factors Annual performance factor《气冷式空调和空气热泵 季节性能.pdf》由会员分享，可在线阅读，更多相关《BS ISO 16358-3-2013 Air-cooled air conditioners and air-to-air heat pumps Testing and calculating methods for seasonal performance factors Annual performance factor《气冷式空调和空气热泵 季节性能.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS ISO 16358-3:2013Air-cooled air conditioners andair-to-air heat pumps Testingand calculating methods forseasonal performance factorsPart 3: Annual performance factorBS ISO 1635

2、8-3:2013 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 16358-3:2013.The UK participation in its preparation was entrusted to TechnicalCommittee RHE/17, Testing of air conditioning units.A list of organizations represented on this committee can beobtained on r

3、equest to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2013. Published by BSI StandardsLimited 2013ISBN 978 0 580 72754 2ICS 23.120; 27.080Compliance with a Br

4、itish Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 30 April 2013.Amendments issued since publicationDate Text affectedBS ISO 16358-3:2013 ISO 2013Air-cooled air conditioners and air-to-a

5、ir heat pumps Testing and calculating methods for seasonal performance factors Part 3: Annual performance factorClimatiseurs condenseur air et pompes chaleur air/air Essais et mthodes de calcul des coefficients de performance saisonniers Partie 3: Coefficient de performance annuel (COPA)INTERNATIONA

6、L STANDARDISO16358-3First edition2013-04-15Reference numberISO 16358-3:2013(E)BS ISO 16358-3:2013ISO 16358-3:2013(E)ii ISO 2013 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2013All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise

7、 in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCase p

8、ostale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 16358-3:2013ISO 16358-3:2013(E) ISO 2013 All rights reserved iiiContents PageForeword iv1 Scope . 12 Normative references 13 Terms and definitions . 14 Symbols 3

9、5 Calculation of annual performance factor (APF) and total annual performance factor (TAPF) . 36 Test report . 3Annex A (informative) Calculation of total annual performance factor (TAPF) 4BS ISO 16358-3:2013ISO 16358-3:2013(E)ForewordISO (the International Organization for Standardization) is a wor

10、ldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on

11、 that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this d

12、ocument and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Direc

13、tives, Part 2. www.iso.org/directivesAttention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development o

14、f the document will be in the Introduction and/or on the ISO list of patent declarations received. www.iso.org/patentsAny trade name used in this document is information given for the convenience of users of this document and does not constitute an endorsement. Equivalent products can be used if the

15、y can be shown to lead to the same results.The committee responsible for this document is ISO/TC 86, Refrigeration and air-conditioning, Subcommittee SC 6, Testing and rating of air-conditioners and heat pumps.The parts of ISO 16358 are given below: Part 1: Cooling seasonal performance factor Part 2

16、: Heating seasonal performance factor Part 3: Annual performance factoriv ISO 2013 All rights reservedBS ISO 16358-3:2013INTERNATIONAL STANDARD ISO 16358-3:2013(E)Air-cooled air conditioners and air-to-air heat pumps Testing and calculating methods for seasonal performance factors Part 3: Annual per

17、formance factor1 Scope1.1 This part of ISO 16358 specifies the testing and calculating methods for seasonal performance factor of equipment covered by ISO 5151, ISO 13253 and ISO 15042.1.2 This part of ISO 16358 also specifies the seasonal performance test conditions and the corresponding test proce

18、dures for determining the seasonal performance factor of equipment, as specified in 1.1., under mandatory test conditions and is intended for use only in marking, comparison, and certification purposes.1.3 This part of ISO 16358 does not apply to the testing and rating of:a) water-source heat pumps

19、or water-cooled air conditioners;b) portable units having a condenser exhaust duct;c) individual assemblies not constituting a complete refrigeration system; ord) equipment using the absorption refrigeration cycle.2 Normative referencesThe following documents, in whole or in part, are normatively re

20、ferenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 5151, Non-ducted air conditioners and heat pumps Testing and rating

21、for performanceISO 13253, Ducted air-conditioners and air-to-air heat pumps Testing and rating for performanceISO 15042, Multiple split-system air-conditioners and air-to-air heat pumps Testing and rating for performanceISO 16358-1, Air-cooled air conditioners and air-to-air heat pumps Testing and c

22、alculating methods for seasonal performance factors Part 1: Cooling seasonal performance factorISO 16358-2, Air-cooled air conditioners and air-to-air heat pumps Testing and calculating methods for seasonal performance factors Part 2: Heating seasonal performance factor3 Terms and definitionsFor the

23、 purposes of this document, the terms and definitions given in ISO 5151, ISO 13253, ISO 15042 and the following apply. ISO 2013 All rights reserved 1BS ISO 16358-3:2013ISO 16358-3:2013(E)3.1cooling seasonal total loadCSTLtotal annual amount of heat that is removed from the indoor air when the equipm

24、ent is operated for cooling in active mode3.2cooling seasonal energy consumptionCSECtotal annual amount of energy consumed by the equipment when it is operated for cooling in active mode3.3cooling seasonal performance factorCSPFratio of the total annual amount of heat that the equipment can remove f

25、rom the indoor air when operated for cooling in active mode to the total annual amount of energy consumed by the equipment during the same period3.4heating seasonal total loadHSTLtotal annual amount of heat, including make-up heat, which is added to the indoor air when the equipment is operated for

26、heating in active mode3.5heating seasonal energy consumptionHSECtotal annual amount of energy consumed by the equipment, including make-up heat, when it is operated for heating in active mode3.6annual performance factorAPFratio of the total annual amount of heat that the equipment can remove from an

27、d add to the indoor air when operated for cooling and heating, respectively, in active mode to the total annual amount of energy consumed by the equipment during the same period3.7total annual performance factorTAPFratio of the total annual amount of heat that the equipment can remove from and add t

28、o the indoor air to the total annual amount of energy consumed by the equipment, including the active, inactive and disconnected modes3.8active modemode corresponding to the hours with cooling and heating demand of the building and whereby the cooling or heating function of the unit is switched on3.

29、9inactive modemode corresponding to the hours when the unit is not operating to meet cooling or heating demandNote 1 to entry: This mode may include the operation of a crankcase heater.3.10disconnected modemode corresponding to the hours when the unit is electrically disconnected from the main power

30、 supplyNote 1 to entry: Power consumption is zero.2 ISO 2013 All rights reservedBS ISO 16358-3:2013ISO 16358-3:2013(E)4 SymbolsSymbol Description UnitCCSEcooling seasonal energy consumption (CSEC) WhCHSEheating seasonal energy consumption (HSEC) WhFAPannual performance factor (APF) FCSPcooling seaso

31、nal performance factor (CSPF) FTAPtotal annual performance factor (TAPF) LCSTcooling seasonal total load (CSTL) WhLHSTheating seasonal total load (HSTL) Wh5 Calculation of annual performance factor (APF) and total annual performance factor (TAPF)Annual performance factor (APF), FAP, shall be calcula

32、ted by Formula (1).FLLCCAPCSTHSTCSEHSE=+(1)Calculation of LCSTand CCSEis according to ISO 16358-1, and calculation of LHSTand CHSEis according to ISO 16358-2.For the cooling-only equipment, the annual performance factor (APF) shall be equal to the cooling seasonal performance factor (CSPF).In case o

33、f calculating the total annual performance factor (TAPF), refer to Annex A.6 Test reportThe test report for this part of ISO 16358 shall include the calculation of APF (and TAPF if applicable) and test reports from ISO 16358-1 for cooling and ISO 16358-2 for heating. ISO 2013 All rights reserved 3BS

34、 ISO 16358-3:2013ISO 16358-3:2013(E)Annex A (informative) Calculation of total annual performance factor (TAPF)A.1 GeneralThis annex applies only to the reverse cycle units.A.2 Measurement of the electric power consumption during the inactive modeThe unit shall be electrically connected to the main

35、power source after shut-down for 6 h. Indoor and outdoor temperature of 20 C condition shall be reached. The power consumption shall be measured for one hour after the temperature conditions are stabilized. The same test is repeated with the temperature condition of 5 C, 10 C and then 15 C with the

36、stabilization period of 2 h between each test. As a reference case, each power consumption value shall be weighted by weighting factors in Table A.1 and then integrated to obtain a weighted average inactive power consumption, Pia. The calculation of inactive power may also be undertaken for other cl

37、imate conditions and operating schedules.NOTE If the results of the tests at 20 C and 5 C are within 5 % or 1 W, then the tests at 15 C and 10 C are not mandatory. The average value of these results is used for the four considered temperature conditions.Table A.1 Default weighting factors for determ

38、ination of reference inactive energy consumptionTemperature condition 5 C 10 C 15 C 20 CWeighting factor 0,05 0,13 0,27 0,55Inactive energy consumption (IAEC) shall be calculated by Formula (A.1).CIAE= Hia Pia(A.1)whereCIAEis the inactive energy consumption;Hiais the number of hours of inactive mode

39、 as given in Table A.2;Piais the weighted average power consumption.A.3 Calculation of total annual performance factor (TAPF)Total annual performance factor (TAPF), FTAP, shall be calculated by Formula (A.2).FTAP= (LCST+ LHST) / (CCSE+ CHSE+ CIAE) (A.2)Calculation of LCSTand CCSEis according to ISO

40、16358-1, and calculation of LHSTand CHSEis according to ISO 16358-2.Inactive energy consumption (IAEC), CIAE, shall be calculated by Formula (A.1).4 ISO 2013 All rights reservedBS ISO 16358-3:2013ISO 16358-3:2013(E)The default mode hours for the calculation of reference total annual performance fact

41、or are shown in Table A.2. The calculation of total annual performance factor may also be undertaken for other distributions of mode hours.Table A.2 Default hours by mode for the calculation of reference total annual performance factorActive mode hInactive mode, HiahDisconnected mode hCooling season

42、 1 817 Heating season 2 866 Annual total hours 4 683 4 077 0 ISO 2013 All rights reserved 5BS ISO 16358-3:2013ISO 16358-3:2013(E) ISO 2013 All rights reservedICS 23.120;27.080Price based on 5 pagesThis page deliberately left blankBSI is the independent national body responsible for preparing British

43、 Standards and other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. BSI is incorporated by Royal Charter. British Standards and other standardisation products are published by BSI Standards Limited.British Stan

44、dards Institution (BSI)raising standards worldwideBSI389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards and PASs are periodically updated by amendment or revision. Users of British Standards and PASs should make sure that they possess the latest amendments or

45、 editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using British Standards would inform the Secretary of the technical committee responsible, the identity of which can be found on the in

46、side frontcover. Similary for PASs, please notify BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers BSI Subscribing Members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of British Standards and PAS

47、s.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Se

48、rvices.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, BSI will supply the British Standard implementation of the relevant international standard, unless otherwise requested.Information on standardsBSI provides a wide range of information on

49、 national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: BSI Subscribing Members are kept up to date with standards developments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8