BS ISO 14972-1999 Sterile obturators for single use with over-needle peripheral intravascular catheters《带过度指针的外部血管内导管的一次使用消毒填塞器》.pdf

《BS ISO 14972-1999 Sterile obturators for single use with over-needle peripheral intravascular catheters《带过度指针的外部血管内导管的一次使用消毒填塞器》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 14972-1999 Sterile obturators for single use with over-needle peripheral intravascular catheters《带过度指针的外部血管内导管的一次使用消毒填塞器》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BSISO 14972:1998 Sterile obturators for single use with over-needle peripheral intravascular catheters ICS 11.040.20BSISO14972:1998 This British Standard, having been prepared under the directionof the Health and Environment Sector Committee, was published under the authorityof the

2、Standards Committee and comes intoeffecton 15 March1999 BSI 05-1999 ISBN 0 580 32122 3 National foreword This British Standard reproduces verbatim ISO14972:1998 and implements it as the UK national standard. The UK participation in its preparation was entrusted to Technical Committee CH/27, Medical

3、plastics tubing, which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UKinterests informed; monitor related international and European developments

4、 and promulgate them in the UK. A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue un

5、der the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct

6、application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, theISO title page, pagesii toiv, pages1 to3 and a back cover. This standard has been updated (see

7、copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No. Date CommentsBSISO14972:1998 BSI 05-1999 i Contents Page National foreword Inside front cover Foreword iii Text of ISO14972

8、1ii blankBSISO14972:1998 ii BSI05-1999 Contents Page Foreword iii 1 Scope 1 2 Normative references 1 3 Definition 1 4 Requirements 1 Annex A (normative) Method for determining force at break of the obturator 3 Annex B (informative) Bibliography 3 Figure 1 Example of obturator 1 Table 1 Force at brea

9、k 2 Table A.1 Example of conditions for a20mm/min/mm strain rate 3BSISO14972:1998 BSI 05-1999 iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally ca

10、rried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work

11、. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires

12、approval by at least75% of the member bodies casting a vote. International Standard ISO14972 was prepared by Technical Committee ISO/TC84, Medical devices for injections, Subcommittee SC1, Syringes, needles and intravascular catheters for single use. Annex A forms a normative part of this Internatio

13、nal Standard. Annex B is for information only.iv blankBSISO14972:1998 BSI 05-1999 1 1 Scope This International Standard specifies requirements for obturators, supplied in the sterile condition and intended for single use for plugging over-needle peripheral catheters. NOTEAttention is drawn to ISO105

14、55-5, which specifies requirements for over-needle peripheral catheters. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this International Standard. At the time of publication, the editions indicated were valid. All s

15、tandards are subject to revision, and parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO maintain registers of currently valid International Standards.

16、ISO594-1:1986, Conical fittings with a6% (Luer) taper for syringes, needles and certain other medical equipment Part1:General requirements. ISO594-2:1998, Conical fittings with a6% (Luer) taper for syringes, needles and certain other medical equipment Par2:Lock fittings. 3 Definition For the purpose

17、s of this International Standard, the following definition applies. 3.1 obturator device designed to be inserted into an over-needle peripheral catheter to plug the lumen of the catheter see Figure 1 4 Requirements 4.1 General The obturator shall have been sterilized by a validated method and it sha

18、ll comply with the requirements given in4.2 to4.10 in the sterile condition. NOTESee ISO11134, ISO11135 and ISO11137 for appropriate methods of sterilization. Figure 1 Example of obturatorBSISO14972:1998 2 BSI 05-1999 4.2 Biocompatibility The obturator shall be free from biological hazard. NOTESee I

19、SO10993-1 for the selection of appropriate test methods. 4.3 Surface When examined by normal or corrected-to-normal vision with2,5 magnification, the external surface of the effective length of the obturator shaft shall appear free from extraneous matter. The external surface and the tip of the obtu

20、rator shaft should be free from surface defects in order to minimize trauma to vessels during use. 4.4 Force at break When tested in accordance with the method given in Annex A, the force at break of the obturator shall be as given in Table 1. 4.5 Luer fitting The Luer fitting shall comply with ISO5

21、94-1 or ISO594-2. 4.6 Outside diameter The outside diameter of the obturator shaft shall be compatible with the inside diameter of the over-needle peripheral catheter(s) with which it is intended to be used in order to plug the lumen of the catheter. 4.7 Effective length When the obturator is fully

22、inserted into the over-needle peripheral catheter, the tip of the obturator shall either coincide with the tip of the catheter or shall extend from the tip of the catheter by no more than3,0mm. 4.8 Colour code The obturator shall be colour-coded with the colour code of the over-needle peripheral cat

23、heter with which it is intended be used. The colour code shall appear on the unit package unless the colour on the product is visible through the unit package. 4.9 Radio-detectability It is recommended that obturators be radio-opaque. At present there is no acceptable, validated test method to deter

24、mine radio-detectability. An approved test method for producing a value of radio-detectability will be established. Until that time, a manufacturer may label the product “radio-opaque” provided this claim can be supported by demonstrating that the manufacturer has an appropriate method for showing r

25、adio-opacity. 4.10 Information to be supplied by the manufacturer The manufacturer shall supply at least the information listed in a) to j). All dimensions given shall be expressed in SI units of measurements. NOTEUnits of other measurement systems may additionally be used. a) Description of the pro

26、duct. b) Suitability for use with a specified over-needle peripheral catheter(s). c) Name or trade name and address of manufacturer. d) Lot designation. e) Expiry date or use by date. f) Any special storage and handling instructions. g) Indication of sterility. h) Method of sterilization. i) Indicat

27、ion for single use. j) Instructions for use and warnings, as appropriate. Table 1 Force at break Smallest outside diameter of obturator shaft mm Minimum force at break N $ 0,350,75 3 $ 0,751,15 5 $ 1,151,85 8 $ 1,85 12BSISO14972:1998 BSI 05-1999 3 Annex A (normative) Method for determining force at

28、break of the obturator A.1 Principle Test pieces of an obturator are chosen so that each obturator portion and each junction between the obturator and the Luer fitting is tested. A tensile force is applied to each test piece until the obturator breaks or the junction separates. A.2 Apparatus A.2.1 T

29、ensile testing apparatus, capable of exerting a force of greater than15N. A.3 Procedure A.3.1 Select a test piece from the obturator to be tested. Include in the test piece the junction between the obturator and the Luer fitting. A.3.2 Condition the test pieces in an atmosphere of100% relative humid

30、ity or water and a temperature of (37 2)C for2h. Test immediately after conditioning. A.3.3 Fix the test piece in the tensile testing apparatus (A.2.1). Use an appropriate fixture to avoid deforming the obturator or the Luer fitting. A.3.4 Measure the gauge length of the test piece (i.e.the distance

31、 between the jaws of the tensile testing apparatus or the distance between the Luer fitting and the jaw holding the other end of the test piece, as appropriate). A.3.5 Apply a tensile strain at unit strain rate of20mm/min per millimetre of gauge length (see Table A.1) until the test piece separates

32、into two or more pieces. Note the value of the applied tensile force, in newtons, at which separation occurs, and record this value as the force at break. A.3.6 Do not perform more than one test on each test piece. Table A.1 Example of conditions for a20mm/min/mm strain rate A.4 Test report The test

33、 report shall include the following information: a) identity of the obturator; b) the force at break, in newtons, and outside diameter of each test piece. Annex B (informative) Bibliography 1 ISO 10555-5:1996, Sterile, single-use intravascular catheters Part5:Over-needle peripheral catheters. 2 ISO

34、10993-1:1997, Biological evaluation of medical devices Part1:Evaluation and testing. 3 ISO 11134:1994, Sterilization of health care products Requirements for validation and routine control Industrial moist heat sterilization. 4 ISO 11135:1994, Medical devices Validation and routine control of ethyle

35、ne oxide sterilization. 5 ISO 11137:1995, Sterilization of health care products Requirements for validation and routine control Radiation sterilization. Gauge length (mm) Testing speed (mm/min) 10 200 20 400 25 500BSISO 14972:1998 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstituti

36、on BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should ma

37、ke sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee res

38、ponsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, internat

39、ional and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested.

40、 Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Co

41、ntact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002.

42、 Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval

43、system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. I

44、f these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.