BS ISO 14368-2-2003 Mineral and sapphire watch-glasses - Assembly to the case by adhesive or using a gasket《无机和蓝宝石表面玻璃 用粘着剂或衬垫组装外壳》.pdf

《BS ISO 14368-2-2003 Mineral and sapphire watch-glasses - Assembly to the case by adhesive or using a gasket《无机和蓝宝石表面玻璃 用粘着剂或衬垫组装外壳》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 14368-2-2003 Mineral and sapphire watch-glasses - Assembly to the case by adhesive or using a gasket《无机和蓝宝石表面玻璃 用粘着剂或衬垫组装外壳》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS ISO 14368-2:2003 Mineral and sapphire watch-glasses Part 2: Assembly to the case by adhesive or using a gasket ICS 39.040.10 BS ISO 14368-2:2003 This British Standard was published under the authority of the Standards Policy and Stratergy Committee on 20 February 2003 BSI 20 Febr

2、uary 2003 ISBN 0 580 41278 4 National foreword This British Standard reproduces verbatim ISO 14368-2:2003 and implements it as the UK national standard. The UK participation in its preparation was entrusted to Technical Committee STI/53, Specifications and test methods for jewellery, horology, which

3、 has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international publications referred to in this document may be found in the BSI Catalogue under the section entitled “

4、International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with

5、 a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related internati

6、onal and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the ISO title page, pages ii and iii, a blank page, pages 1 to 5 and a back cover. The BSI copyright date displayed in this document indicates when the documen

7、t was last issued. Amendments issued since publication Amd. No. Date Comments Reference number ISO 14368-2:2003(E)INTERNATIONAL STANDARD ISO 14368-2 First edition 2003-02-01 Mineral and sapphire watch-glasses Part 2: Assembly to the case by adhesive or using a gasket Verres de montres minraux et en

8、saphir Partie 2: Fixation la bote par collage ou laide dun joint BSISO143682:2003DPlcsid Fremia ihTs PDF file mya ctnoian emdebt dedyfepcaes. In ccacnadrow eitA hebods licnesilop gnic,y tihs file mirp eb yatnde iv roweb detu slahl ton ide ebtlnu deess teh typfecaes wihce era hml era deddebicsnede ti

9、 dna onstlalde t noeh comuptfrep reromign tide ehtin.g In wodlnidaot gnihs fil,e trapise atpecc tiereht nser ehnopsiiblity fo nto ifnriigngn Aebods licnesilop gnic.y ehT ISO tneClar Secrteirata caceptl on siibality in this .aera Ai ebods a tedarmfo kra Aebod SystemI snctaropro.de teDials fo teh sfot

10、wcudorp erats sut deo crtaee tihs PDF file cna f ebi dnuon tlareneG eh Ifnler oatit evt oeh file; tP ehDc-Frtaeino marapterew stpo ereimizde fro irptni.gn Evyre cera neeb sah takne tsne oeru taht teh file is siutlbae fosu re yb ISO memdob rebeis. In tlnu ehikletneve y ttah lborp aem lertait gno it i

11、s f,dnuo plsaee ifnrom ttneC ehlar Secterirata ta teh serddaig sleb nevwo. ISO 3002 All irthgs erse.devr lnUeto sswrehise specified, on trap fo this lbupictaion maeb y cudorperro de tuilizi den yna form ro na ybm ynae,s lecetrinoc ro mceinahcla, incliduntohp gcoiypodna gn micrfoilm, wittuoh repmissi

12、i now nritign from ietI rehSa Ot tsserdda eh ebolw or ISOs memreb i ydobn the cnuotfo yr ttseuqer ehe.r ISO cirypothg fofice saCe tsopale 65 eneG 1121-HC 02 av leT. 4 + 10 947 22 1 11 xaF0 947 22 14 + 9 74 E-mial coirypthgis.o gro We bwww.is.o groii BSISO143682:2003 iiiForeword ISO (the Internationa

13、l Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been es

14、tablished has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardi

15、zation. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for vot

16、ing. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all suc

17、h patent rights. ISO 14368-2 was prepared by Technical Committee ISO/TC 114, Horology, Subcommittee SC 13, Watch- glasses. ISO 14368 consists of the following parts, under the general title Mineral and sapphire watch-glasses: Part 1: Dimensions and tolerances Part 2: Assembly to the case by adhesive

18、 or using a gasket Part 3: Qualitative criteria and test methods BSISO143682:2003INTENRATIONAL TSANDADR IS-86341 O2:(3002E)1Mineral and sapphire watch-glasses Part 2: Assembly to the case by adhesive or using a gasket 1 Scope This part of ISO 14368 specifies dimensional requirements of the interface

19、 for the assembly to the case by adhesive or using a gasket for round-shaped mineral and sapphire watch-glasses. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated referen

20、ces, the latest edition of the referenced document (including any amendments) applies. ISO 286-1, ISO system of limits and fits Part 1: Bases of tolerances, deviations and fits ISO 286-2, ISO system of limits and fits Part 2: Tables of standard tolerance grades and limit deviations for holes and sha

21、fts ISO 14368-1, Mineral and sapphire watch-glasses Part 1: Dimensions and tolerances 3 Terms, definitions and symbols 3.1 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 286-1 and ISO 286-2 apply. 3.2 Symbols The symbols and terms used in Figures 1, 2

22、 and 3 are given in Table 1. BSISO143682:20032 Table 1 Symbols and terms Symbol Term c gasket compression in % of width d diameter of the glass d 1dial opening diameter d 2diameter of the circular groove of the glass d 3external gasket diameter (non-compressed) d 4internal gasket diameter (non-compr

23、essed) e 1gasket thickness e 2thickness of compressed gasket e 3space for adhesive h 1cylindrical side height of the glass h 2height of the lower slope of the glass h 3height of the upper slope of the glass h 4determining height for glasses assembled with adhesive h 5height of the circular groove of

24、 the glass h 6height of the internal slopes of the gasket h 7height of compressed gasket h 8height of non-compressed gasket t total thickness of the glass angle of the lower slope of the glass angles of the internal slopes of the gasket Figure 1 Glass secured by adhesive BSISO143682:2003 3Figure 2 F

25、ixing the glass with a gasket Figure 3 Details of the gasket 4 Dimensions 4.1 Glass secured by adhesive 4.1.1 General The dimensions for glass secured by adhesive shall be as given in Figure 1. 4.1.2 Opening The dial opening diameter is calculated using the following equation: d 1u d 0,40 mm or d (2

26、 h 2+ 0,20 mm) BSISO143682:20034 where h 2is in accordance with ISO 14368-1. 4.1.3 Glass circular groove The diameter of the circular groove is calculated using the following equation: d 2= d + 2 e 3where e 3= 0,03 mm to 0,05 mm 4.2 Glass secured with a gasket 4.2.1 General The dimensions for glass

27、secured with a gasket shall be as given in Figures 2 and 3. 4.2.2 Opening The dial opening diameter is calculated using the following equation: d 1u d (2 h 2 tan) + 0,20 mm where h 2is in accordance with ISO 14368-1. 4.2.3 Glass circular groove The diameter of the glass circular groove is calculated

28、 using the following equation: d 2= d + 2 e 24.2.4 Assembly The assembly shall be carried out using either of the two following methods. a) The gasket is first housed in the groove and then the glass is driven in. b) The gasket is first fitted onto the glass surround and is then driven into the glas

29、s groove; this method is valid only for L gaskets, which are not dealt with in this part of ISO 14368. 5 Gasket dimensions The gasket dimensions shall be as given in Table 2. BSISO143682:2003 5Table 2 Gasket dimensions Term Dimension External gasket diameter d 3= d 2Internal gasket diameter d 4= d 3

30、 2 e 1(e 1= e 2+ c) Gasket height after fitting h 7max. = h 5 0,05 mm Height of the circular groove of the glass h 5= h 4 or h 5= t h 3Compression c = 15 % to 35 % of e 1(by taking into account the characteristics of the gasket material) Internal slope angles of the gasket = 30 to 45 Height of the i

31、nternal slopes of the gasket h 6= 0,10 mm to 0,30 mm Height of gasket before fitting h 8= define according to the material 6 Tolerances The tolerances shall be as given in Table 3. Table 3 Tolerances Symbol Tolerance d in accordance with ISO 14368-1 t in accordance with ISO 14368-1 d 1J s 9 d 2J s 8

32、 d 3s10 h 5j s 9 BSISO143682:2003BS ISO 14368-2:2003 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incor

33、porated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyo

34、ne finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PL

35、US which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. Standards are also available from the BSI

36、website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European

37、and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members

38、 of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Further information about BSI is available on the BSI websi

39、te at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrie

40、val system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designation

41、s. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.