BS ISO 13765-2-2006 Refractory mortars - Determination of consistency using the reciprocating flow table method《耐熔灰浆 使用往复流动表法测定一致性》.pdf

《BS ISO 13765-2-2006 Refractory mortars - Determination of consistency using the reciprocating flow table method《耐熔灰浆 使用往复流动表法测定一致性》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 13765-2-2006 Refractory mortars - Determination of consistency using the reciprocating flow table method《耐熔灰浆 使用往复流动表法测定一致性》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、 g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58ICS 81.080Refractory mortars Part 2: Determination of consistency using the reciprocating flow tabl

2、e methodBRITISH STANDARDBS ISO 13765-2:2004BS ISO 13765-2:2004This British Standard was published under the authority of the Standards Policy and Strategy Committee on 13 February 2006 BSI 13 February 2006ISBN 0 580 47703 7Cross-referencesThe British Standards which implement international publicati

3、ons referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online.This publication does not purport to include all the necessar

4、y provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations.Summary of pagesThis document comprises a front cover, an inside front cover, the ISO title page, pages ii and iii, a blank page

5、, pages 1 to 5 and a back cover.The BSI copyright notice displayed in this document indicates when the document was last issued.Amendments issued since publicationAmd. No. Date CommentsA list of organizations represented on this committee can be obtained on request to its secretary. present to the r

6、esponsible international/European committee any enquiries on the interpretation, or proposals for change, and keep UK interests informed; monitor related international and European developments and promulgate them in the UK.National forewordThis British Standard reproduces verbatim ISO 13765-2:2004

7、and implements it as the UK national standard. Together with BS ISO 13765-1, BS ISO 13765-3, BS ISO 13765-4, BS ISO 13765-5 and BS ISO 13765-6, it supersedes BS 1902-11:1991, which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee RPI/1, Refractories, which ha

8、s the responsibility to: aid enquirers to understand the text;INTERNATIONALSTANDARDISO13765-2First edition2004-06-01Reference numberISO 13765-2:2004(E)Refractory mortars Part 2:Determination of consistency using the reciprocating flow table methodMortiers rfractaires Partie 2: Dtermination de la con

9、sistance par la mthode de la table dcoulement mouvement alternatifBS ISO 13765-2:2004iiiiiForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies(ISO member bodies). The work of preparing International Standards is normally carried out

10、through ISOtechnical committees. Each member body interested in a subject for which a technical committee has beenestablished has the right to be represented on that committee. International organizations, governmental andnon-governmental, in liaison with ISO, also take part in the work. ISO collabo

11、rates closely with the InternationalElectrotechnical Commission (IEC) on all matters of electrotechnical standardization.International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.The main task of technical committees is to prepare International Standard

12、s. Draft International Standardsadopted by the technical committees are circulated to the member bodies for voting. Publication as anInternational Standard requires approval by at least 75 % of the member bodies casting a vote.Attention is drawn to the possibility that some of the elements of this d

13、ocument may be the subject of patentrights. ISO shall not be held responsible for identifying any or all such patent rights.ISO 13765-2 was prepared by Technical Committee ISO/TC 33, Refractories.ISO 13765 consists of the following parts, under the general title Refractory mortars: Part 1: Determina

14、tion of consistency using the penetrating cone method Part 2: Determination of consistency using the reciprocating flow table method Part 3: Determination of joint stability Part 4: Determination of flexural bonding strength Part 5: Determination of grain size distribution (sieve analysis) Part 6: D

15、etermination of moisture content of ready-mixed mortarsBS ISO 13765-2:2004blank1Refractory mortars Part 2:Determination of consistency using the reciprocating flow table method1ScopeThis part of ISO 13765 describes a method for the determination of the consistency of refractory mortars usinga recipr

16、ocating flow table.2 Normative referencesThe following referenced documents are indispensable for the application of this document. For datedreferences, only the edition cited applies. For undated references, the latest edition of the referenced document(including any amendments) applies.ISO 8656-1,

17、 Refractory products Sampling of raw materials and unshaped products Part 1: Samplingscheme3 Terms and definitionsFor the purposes of this document, the terms and definitions given in ISO 13765-1 apply.4 PrincipleThe consistency of a refractory mortar is assessed by measuring the increase in diamete

18、r of a sample whensubjected to up and down mechanical agitation using a reciprocating flow table.5 Apparatus5.1 Flow table and mould, as shown in Figure 1.5.2 Mixer, consisting of:5.2.1 Stainless steel bowl, with a capacity of about 5 litres and of the general shape and size shown inFigure 2, and pr

19、ovided with means by which it can be fixed securely to the mixer frame during mixing and bywhich the height of the bowl in relation to the blade and, to some extent, the gap between blade and bowl canbe finely adjusted and fixed.BS ISO 13765-2:20042Dimensions in millimetresKey1 lines to be scribed o

20、n face of table2 table (brass or bronze)3 conical mould4 directions of movement of the flow table5 table to be fixed to shaft and total mass to be 6 handle, or alternatively, motor drive through flexible shaft7drop8 sides machined to give a drop of 9 fixing holes10 hardened contact faces11 view of u

21、nderside of tableFigure 1 Flow table and mould4kg 0,5 kg12,7 mm 0,1 mmBS ISO 13765-2:200435.2.2 Metal blade, of the general shape, size and tolerances shown in Figure 2, rotating about its own axis asit is driven in a planetary movement around the axis of the bowl by an electric motor at controlled

22、rotationalfrequencies.The two directions of rotation shall be opposite and the ratio between the two frequencies shall not be a wholenumber. Where more than one mixer is used, blades and bowls shall form sets which are always used together.The gap between blade and bowl shown in Figure 2 shall be ch

23、ecked every month.NOTE The gap indicated in Figure 2 ( ) refers to the situation when the blade in the empty bowl is brought asclose as possible to the wall. Simple tolerance gauges (feeler gauges) are useful where direct measurement is difficult.5.3 Thermometer.5.4 Palette knife.5.5 Measuring cylin

24、der.6 SamplingFor dry mortar, sample the mortar in accordance with ISO 8656-1 or as agreed between parties. Reduce thesample to by quartering or with a riffle sampler.Dimensions in millimetresKey1bowl2bladeFigure 2 Mixer blade and bowl3mm 1mm5kgBS ISO 13765-2:20044Sample ready-mixed mortars by empty

25、ing the entire contents of the container in which the mortar is suppliedinto another container of larger capacity and mixing thoroughly. It is important that any supernatant liquid is notdiscarded. Ensure that a representative sample of the wet mixture is obtained.7 ProcedureCarry out the determinat

26、ion in triplicate.If the table has not been used for or more, operate for 10 revolutions before use. Wipe the flow table topuntil clean and dry and place the clean dry mould at the centre.For dry mortars, place the mortar in the mixer and add water (or the specified mixing liquid) in accordance with

27、the manufacturers instructions and mix thoroughly. Note the quantity of liquid added. Allow the mixed mortar tostand for , unless any specific instructions are given by the manufacturer in which case these shall befollowed. Ready-mixed mortar shall be tested in “as received” state.Measure the temper

28、ature of the mixed mortar to the nearest .Fill the mould uniformly with the mortar. Using a palette knife, strike off the mortar surface plane and level withthe top of the mould. Wipe the surrounding table top clean and dry, being especially careful to remove any waterfrom around the edge of the mou

29、ld. Lift the mould away vertically. Remove any material left in the mould with aknife and place this on top of the material on the table. Operate the flow table 25 times in about . Measurethe average diameter of the mortar to the nearest millimetre in two directions at right angles.8 CalculationFor

30、each of the three determinations, calculate the consistency as the flow index, , in percent, using theequation:whereis the mean diameter of the mortar after operating the flow table as described in Clause 7;is the internal base diameter of the mould.Report the consistency of the mortar as the mean v

31、alue of the three flow index results to the nearest .9 Test reportThe report shall include the following information:a) all information necessary for identification of the material tested, including a description of the material,manufacturer, type, brand, batch number, etc.;b) a reference to this pa

32、rt of ISO 13765 (ISO 13765-2);c) the name of the testing establishment;d) in the case of a dry mortar, the percentage of water (or specified liquid) added;e) the results of the test, i.e. the flow index to the nearest , including the results of the individualdeterminations and their mean, calculated

33、 as specified in Clause 8;f) the ambient temperature at which the test was conducted;g) the temperature of the mixed mortar;h) any deviations from the procedure specified;24 h15 min1C15 sFF =DDoDo 100DDo1%1%BS ISO 13765-2:20045i) any unusual features (anomalies) observed during the test;j) the date

34、of the test.BS ISO 13765-2:2004BS ISO BSI389 Chiswick High RoadLondonW4 4AL13765-2:2004BSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated

35、by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding

36、an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PL

37、US which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are

38、 also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of informat

39、ion on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +4

40、4 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996

41、 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright,

42、 in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise wi

43、thout prior written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.