BS ISO 13459-2012 Earth-moving machinery Trainer seat Deflection limiting volume space envelope and performance requirements《土方机械 教练员座椅 挠曲极限量 空间封套和性能要求》.pdf

《BS ISO 13459-2012 Earth-moving machinery Trainer seat Deflection limiting volume space envelope and performance requirements《土方机械 教练员座椅 挠曲极限量 空间封套和性能要求》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 13459-2012 Earth-moving machinery Trainer seat Deflection limiting volume space envelope and performance requirements《土方机械 教练员座椅 挠曲极限量 空间封套和性能要求》.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS ISO 13459:2012Earth-moving machinery Trainer seat Deflectionlimiting volume, spaceenvelope and performancerequirementsBS ISO 13459:2012 BRITISH STANDARDNational forewordThis B

2、ritish Standard is the UK implementation of ISO 13459:2012.The UK participation in its preparation was entrusted to TechnicalCommittee B/513/1, Earth moving machinery (International).A list of organizations represented on this committee can beobtained on request to its secretary.This publication doe

3、s not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2012. Published by BSI StandardsLimited 2012ISBN 978 0 580 67749 6ICS 53.100Compliance with a British Standard cannot confer immunity fromlegal obli

4、gations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 December 2012.Amendments issued since publicationDate Text affectedBS ISO 13459:2012 ISO 2012Earth-moving machinery Trainer seat Deflection limiting volume, space envelope and performa

5、nce requirementsEngins de terrassement Sige de linstructeur Volume limite de dformation, espace enveloppe et exigences de performanceINTERNATIONAL STANDARDISO13459Second edition2012-07-15Reference numberISO 13459:2012(E)BS ISO 13459:2012ISO 13459:2012(E)ii ISO 2012 All rights reservedCOPYRIGHT PROTE

6、CTED DOCUMENT ISO 2012All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs mem

7、ber body in the country of the requester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 13459:2012ISO 13459:2012(E)ForewordISO (the International Organization for Standardization) is

8、 a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represen

9、ted on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.International Standards are dra

10、fted in accordance with the rules given in the ISO/IEC Directives, Part 2.The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Sta

11、ndard requires approval by at least 75 % of the member bodies casting a vote.Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.ISO 13459 was prepared by

12、 Technical Committee ISO/TC 127, Earth-moving machinery, Subcommittee SC 2, Safety, ergonomics and general requirements.This second edition cancels and replaces the first edition (ISO 13459:1997), which has been technically revised. ISO 2012 All rights reserved iiiBS ISO 13459:2012BS ISO 13459:2012E

13、arth-moving machinery Trainer seat Deflection limiting volume, space envelope and performance requirements1 ScopeThis International Standard specifies the trainer-seat deflection limiting volume (DLV), space envelope and performance requirements, and dimensions, for use in laboratory evaluations of

14、protective structures on earth-moving machinery as defined in ISO 6165.The effects of vibration are not considered a significant risk for short-term or temporary seats and are therefore outside the scope of this International Standard.2 Normative referencesThe following referenced documents are indi

15、spensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 2867, Earth-moving machinery Access systemsISO 3411, Earth-moving machinery Physical dime

16、nsions of operators and minimum operator space envelopeISO 3449, Earth-moving machinery Falling-object protective structures Laboratory tests and performance requirementsISO 3471, Earth-moving machinery Roll-over protective structures Laboratory tests and performance requirementsISO 5006, Earth-movi

17、ng machinery Operators field of view Test method and performance criteriaISO 5353, Earth-moving machinery, and tractors and machinery for agriculture and forestry Seat index pointISO 6165, Earth-moving machinery Basic types Identification and terms and definitionsISO 6683, Earth-moving machinery Sea

18、t belts and seat belt anchorages Performance requirements and testsISO 9248, Earth-moving machinery Units for dimensions, performance and capacities, and their measurement accuraciesISO 10262, Earth-moving machinery Hydraulic excavators Laboratory tests and performance requirements for operator prot

19、ective guardsISO 12117-2, Earth-moving machinery Laboratory tests and performance requirements for protective structures of excavators Part 2: Roll-over protective structures (ROPS) for excavators of over 6 tISO 20474-1, Earth-moving machinery Safety Part 1: General requirementsINTERNATIONAL STANDAR

20、D ISO 13459:2012(E) ISO 2012 All rights reserved 1BS ISO 13459:2012ISO 13459:2012(E)3 Terms and definitionsFor the purposes of this document, the following terms and definitions apply.3.1locating axisLAhorizontal axis for positioning the DLV (3.2) with respect to the seat index point (SIP)3.2deflect

21、ion limiting volumeDLVorthogonal approximation of a large, seated operator, as defined in ISO 3411, wearing normal clothing and a protective helmetNOTE 1 Adapted from ISO 3164:1995, definition 3.1.NOTE 2 The DLV applies to the operator, whereas the trainer DLV (3.7) applies to the trainer and traine

22、r seat.3.3operator spacespace around the operator3.4orthogonal top head planeupper 270 mm 330 mm rectangular horizontal surface of the DLV (3.2) for FOPS testingSee Figure A.1.3.5trainer seatseat installed in the operators compartment, adjacent to or behind the operators seat, for short-term or temp

23、orary usage for the primary purpose of training an operator3.6trainer space envelopeenvelope in which the trainer performs job tasksSee Figure 1.3.7trainer DLVapproximation of a large, seated trainer wearing normal clothing and a protective helmetSee Figure A.1.NOTE Adapted from ISO 3164:1995, defin

24、ition 3.1. (The trainer is assumed to be the same size as the large operator in that definition and in definition 3.2).3.8handholddevice which the trainer can hold onto, providing support and preventing body movement2 ISO 2012 All rights reservedBS ISO 13459:2012ISO 13459:2012(E)4 Requirements4.1 Se

25、at dimensionsTrainer seats shall have dimensions in accordance with Table 1, unless a deviation is justified based on unusual ergonomic considerations. All dimensions shall be referenced to the seat index point (SIP), determined in accordance with ISO 5353. The trainer seat may consist of independen

26、t cushions, provided they conform to the required dimensions.4.2 Trainer seat location4.2.1 The trainer seat shall be installed within the operators station.4.2.2 No portion of the trainer seat shall be located in the sector of vision A, as defined in ISO 5006. The trainer seat shall be positioned s

27、o as to provide adequate visibility for observing the operator and the work environment. The location of the trainer seat shall not interfere with the safe operation of the machine by the operator.4.3 Trainer space envelope dimensions/adjustment/suspensionThe trainer space envelope shall have the di

28、mensions given in Figure 1. Seat adjustment and suspension is not required for a trainer seat.4.4 FOPS or top-guard requirements for trainer seatsThe FOPS (falling-object protective structure) requirements of ISO 3449 or top-guard requirements of ISO 10262 apply to the trainer seat using the trainer

29、 DLV, in accordance with Annex A. Results from FOPS or top-guard testing for the operator may be used to evaluate and verify compliance with this International Standard if the cab structure is shown through analysis to be stronger above the trainer.4.5 ROPS requirements for trainer seats4.5.1 Genera

30、lThe ROPS (roll-over protective structure) requirements given in ISO 3471 or ISO 12117-2, together with the provisions of 4.5.2 and 4.5.3, apply to trainer seats. Results from ROPS testing in accordance with ISO 3471 or ISO 12117-2 for the operator may also be used to evaluate and verify compliance

31、with 4.5.3.See also Annex B.4.5.2 ROPS test procedureTest the ROPS structure in accordance with ISO 3471 or ISO 12117-2, using the trainer DLV provisions given in Annexes A and B.4.5.3 ROPS acceptance criteriaThe acceptance criteria of ISO 3471 or ISO 12117-2, together with those of Annex B, apply.4

32、.6 Trainer seat ROPS/FOPS or top-guard labellingIf the acceptance criteria given in Annex B have been met, a reference to this International Standard shall be added to the ROPS/FOPS or top-guard label. ISO 2012 All rights reserved 3BS ISO 13459:2012ISO 13459:2012(E)4.7 MaterialsMaterials used for th

33、e trainer seat and its fittings shall be flame-retardant and in accordance with ISO 20474-1.4.8 HandholdA handhold meeting the dimensional requirements for handholds given in ISO 2867 shall be placed within arms reach of the person seated in the trainer seat. The handhold may be the same one as that

34、 used to push to open or pull to close the door. The door latch mechanism for latching and unlatching the door shall not be used as a handhold.4.9 StorageThe trainer seat may be stored or removed when not in use.4.10 Restraint systemThe trainer seat shall have a restraint system (e.g. seat belt and

35、seat belt anchorage) in accordance with ISO 6683.Table 1 Trainer seat dimensionsDimensions in millimetresDimension Description Maximum Basic MinimumB Seat cushion length 320 300 215D Seat cushion width 360 300G Back cushion height 400 150H Back cushion width 360 300J Back cushion angle 15 10 0For th

36、e SIP, see ISO 5353.SIPBJHDG4 ISO 2012 All rights reservedBS ISO 13459:2012ISO 13459:2012(E)Dimensions in millimetresSIPSIPSIPYXXXXYZZZZ215 350215 350515500R 950R 400R 950570111R1 1 050 (with protective helmet) or R1 1 000 (without protective helmet). For the SIP, see ISO 5353.Figure 1 Trainer space

37、 envelope ISO 2012 All rights reserved 5BS ISO 13459:2012ISO 13459:2012(E)Annex A (normative) Trainer DLV dimensionsThe dimensions of the trainer DLV shall be as shown in Figure A.1.NOTE Orthogonal top head plane for use with a rounded DLV for FOPS testing.Dimensions in millimetres6 ISO 2012 All rig

38、hts reservedBS ISO 13459:2012ISO 13459:2012(E)A is the front boundary plane and B the rear boundary plane. For the SIP, see ISO 5353.aMay be reduced to avoid interference with floor plates.bMachine parts or controls can cause feet to be separated. As a minimum, the crush-proof volume for feet and le

39、gs in ISO 3411 shall be maintained on both sides.cFeet may move 45 mm rearward.Figure A.1 Trainer DLV dimensions ISO 2012 All rights reserved 7BS ISO 13459:2012ISO 13459:2012(E)Annex B (normative) Trainer DLV acceptance criteriaB.1 The portion of the trainer DLV above the SIP shall be permitted to r

40、otate (see Figure B.1) and translate as per the following.a) During lateral and longitudinal loading, it is permissible for the upper portion of the trainer DLV to be rotated sideways or forwards in the direction of ROPS deflection up to 15 around the locating axis (LA) line (see 3.1 and ISO 5353).

41、The portion below the LA line of the DLV may be disregarded. The rotation of the trainer DLV shall be limited to 15. If there is interference with any machine components or controls at a lesser angle, that angle shall be the limit of rotation. Upper-portion additional rotation due to deformation of

42、the mounting surface on which the trainer DLV is mounted is allowed.b) The trainer DLV may be also be translated 50 mm laterally or longitudinally in the direction of ROPS loading, to allow for soft tissue deflection of a large trainer.B.2 When the trainer DLV is rotated up to a maximum of 16 in the

43、 direction of ROPS deflection, the operator space shall allow the operator DLV to rotate by up to a maximum of 15 to avoid interference between the two DLVs.B.3 For rigid-frame dumpers that have the operator seat closer to the edge of the machine than the trainer seat, or that have side-mounted oper

44、ator stations and no appreciable lateral load on the trainer-seat side during a roll-over event, compliance with ISO 3471 meets the ROPS requirements for the trainer seat given in this International Standard (see 4.5).B.4 Measurement accuracy shall be in accordance with ISO 9248.15SIP15SIPa) Lateral

45、 load on roller with sideways-mounted seatb) Longitudinal load on tractor-dozer8 ISO 2012 All rights reservedBS ISO 13459:2012ISO 13459:2012(E)1515SIP SIPc) Lateral load on roller with forward-mounted seatFigure B.1 Allowable rotation of upper DLV about SIP ISO 2012 All rights reserved 9BS ISO 13459

46、:2012ISO 13459:2012(E)Bibliography1 ISO 3164, Earth-moving machinery Laboratory evaluations of protective structures Specifications for deflection-limiting volume2 ISO 11112, Earth-moving machinery Operators seat Dimensions and requirements10 ISO 2012 All rights reservedBS ISO 13459:2012BS ISO 13459

47、:2012ISO 13459:2012(E) ISO 2012 All rights reservedICS 53.100Price based on 10 pagesThis page deliberately left blankBSI is the independent national body responsible for preparing British Standards and other standards-related publications, information and services. It presents the UK view on standar

48、ds in Europe and at the international level. BSI is incorporated by Royal Charter. British Standards and other standardisation products are published by BSI Standards Limited.British Standards Institution (BSI)raising standards worldwideBSI389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 90

49、01Fax +44 (0)20 8996 Standards and PASs are periodically updated by amendment or revision. Users of British Standards and PASs should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using British Standards woul