BS ISO 13263-2010 Thermoplastics piping systems for non-pressure underground drainage and sewerage - Thermoplastics fittings - Test method for impact strength《无压地下排水和排污用热塑性塑料管道系统 热.pdf

《BS ISO 13263-2010 Thermoplastics piping systems for non-pressure underground drainage and sewerage - Thermoplastics fittings - Test method for impact strength《无压地下排水和排污用热塑性塑料管道系统 热.pdf》由会员分享，可在线阅读，更多相关《BS ISO 13263-2010 Thermoplastics piping systems for non-pressure underground drainage and sewerage - Thermoplastics fittings - Test method for impact strength《无压地下排水和排污用热塑性塑料管道系统 热.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BS ISO13263:2010ICS 23.040.20; 23.040.45; 91.140.80; 93.030NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDThermoplastics pipingsystems for non-pressure undergrounddrainage and sewerage Thermoplasticsfittings Test methodfor impact strengthThis British Standardwa

2、s published under theauthority of the StandardsPolicy and StrategyCommittee on 30 June2010 BSI 2010ISBN 978 0 580 66713 8Amendments/corrigenda issued since publicationDate CommentsBS ISO 13263:2010National forewordThis British Standard is the UK implementation of ISO 13263:2010.The UK participation

3、in its preparation was entrusted to TechnicalCommittee PRI/88/1, Plastics piping for non-pressure applications.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. User

4、s are responsible for its correct application.Compliance with a British Standard cannot confer immunityfrom legal obligations.BS ISO 13263:2010Reference numberISO 13263:2010(E)ISO 2010INTERNATIONAL STANDARD ISO13263First edition2010-05-01Thermoplastics piping systems for non-pressure underground dra

5、inage and sewerage Thermoplastics fittings Test method for impact strength Systmes de canalisations thermoplastiques pour branchements et collecteurs dassainissement enterrs sans pression Raccords thermoplastiques Mthode dessai de rsistance au choc BS ISO 13263:2010ISO 13263:2010(E) PDF disclaimer T

6、his PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept t

7、herein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file;

8、 the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DO

9、CUMENT ISO 2010 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member bo

10、dy in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2010 All rights reservedBS ISO 13263:2010ISO 13263:2010(E) ISO 2010 All rights reserved iiiF

11、oreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a te

12、chnical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters

13、of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated

14、 to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible f

15、or identifying any or all such patent rights. ISO 13263 was prepared by Technical Committee ISO/TC 138, Plastics pipes, fittings and valves for the transport of fluids, Subcommittee SC 1, Plastics pipes and fittings for soil, waste and drainage (including land drainage). BS ISO 13263:2010BS ISO 1326

16、3:2010INTERNATIONAL STANDARD ISO 13263:2010(E) ISO 2010 All rights reserved 1Thermoplastics piping systems for non-pressure underground drainage and sewerage Thermoplastics fittings Test method for impact strength 1 Scope This International Standard specifies a method for testing the impact resistan

17、ce of fittings by dropping them on to a rigid surface. For a fitting with seal-retaining components, such as seal-retaining caps or rings, the method includes assessment of the watertightness of the fittings when the fixing elements show damage as a result of the test. This International Standard is

18、 applicable to fittings made from thermoplastics materials intended to be used for buried and above-ground applications. 2 Principle The impact resistance of a fitting is tested by dropping the fitting on to a rigid surface. After impact, the fitting is inspected for any cracks visible without magni

19、fication. In the case of fittings with separate fixing elements, for example for seal retention, these elements are inspected for any permanent damage that could cause loss of watertightness. NOTE It is assumed that the following test parameters are set by the referring standard: a) test temperature

20、 (see Clause 3); b) sampling procedure and frequency (see Clause 4); c) conditioning time and temperature, as applicable (see Clause 5); d) the height from which the test piece is to be dropped (see Clause 6); e) the point of impact that is to hit the test base when dropped (see Clause 6); f) test c

21、onditions for assessment of watertightness (see Clauses 6 and 7). 3 Apparatus 3.1 Refrigerator or liquid bath, capable of maintaining the conditioning temperature within 2 C. 3.2 Temperature-controlled environment, capable of maintaining the test temperature within 2 C. 3.3 Test base, comprising a s

22、olid floor made of concrete or stone at least 100 mm thick or, alternatively, a slab of concrete with a minimum thickness of 100 mm and a mass at least 20 times that of the test piece. The surface shall be rigid, flat, smooth and horizontal. BS ISO 13263:2010ISO 13263:2010(E) 2 ISO 2010 All rights r

23、eserved4 Test pieces 4.1 Test piece form The test piece shall comprise a sample fitting complete, where applicable, with the sealing element and any associated means of the fixing element(s) in place. 4.2 Sampling The sampling procedure and frequency shall be as specified in the referring standard.

24、4.3 Number Unless otherwise specified in the referring standard, the number of test pieces shall be five for sizes up to and including 200 mm, and three for sizes greater than 200 mm. 5 Conditioning Determine and measure the maximum wall thickness, e, of the sample fitting. Place the test piece in t

25、he refrigerator, liquid bath or temperature-controlled environment (3.1 and 3.2) at the specified test temperature for at least the applicable minimum period given in Table 1, unless otherwise specified in the referring standard. Table 1 Minimum conditioning temperature Wall thickness e mm Minimum c

26、onditioning period h e 630: 60 Temperature-controlled environment (3.2) with refrigerator or liquid bath (3.1) in the same environment 60 BS ISO 13263:2010ISO 13263:2010(E) ISO 2010 All rights reserved 36.2 Release the fitting from the specified drop height in such a manner that the specified point

27、of impact hits the test base. The position from which the fitting shall be dropped in order to hit the specified impact point may be decided by preliminary testing with each specific fitting type. 6.3 Inspect each fitting for, and record the presence and positions of, any cracks or splits visible wi

28、thout magnification. Disregard any surface scratches, scuffing or chipping of edges that may occur during the test. Assess the condition and/or assembly of the test piece for watertightness using the applicable test method(s) specified in the referring standard to express the result in accordance wi

29、th Clause 7. 7 Expression of results 7.1 Unless otherwise specified in the referring standard, if the fitting shows no cracks through the wall and the condition in 7.2 is conformed to, express the result as “No damage”. 7.2 If, during the test, the fixing element jumps off the fitting body but can b

30、e restored manually to its correct position, e.g. to give a watertight joint, and if the condition in 7.1 is conformed to, express the result as “No damage”. 7.3 If the fitting shows cracks through the wall or if the fixing element has jumped off the fitting without the possibility of restoring it i

31、n such a way that watertight jointing is achieved, express the result as “Damage”. 8 Test report The test report shall include the following information: a) a reference to this International Standard, i.e. ISO 13263:2010, and the referring standard; b) complete identification of the fitting under te

32、st; c) the test temperature; d) the height from which the fitting(s) was (were) dropped; e) the point of impact; f) for each test piece, the results of the test and any associated information; g) any factor that could have affected the results, such as any incident or any operating detail not specif

33、ied in this International Standard; h) the date of the test. BS ISO 13263:2010ISO 13263:2010(E) ICS 23.040.20; 23.040.45; 91.140.80; 93.030 Price based on 3 pages ISO 2010 All rights reserved BS ISO 13263:2010This page has been intentionally left blank BS ISO13263:2010BSI GroupHeadquarters 389Chiswi

34、ck High Road,London, W4 4AL, UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 - British Standards InstitutionBSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at theinternational level. It is incorporated by Royal Charter.

35、RevisionsBritish Standards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments oreditions.It is the constant aim of BSI to improve the quality of our products and services.We would be grateful if anyone finding an inaccuracy or amb

36、iguity while usingthis British Standard would inform the Secretary of the technical committeeresponsible, the identity of which can be found on the inside front cover. Tel:+44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensuresthat su

37、bscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should beaddressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 89967001 Email: You may also buy directly using a debit/creditcard

38、from the BSI Shop on the Website http:/ response to orders for international standards, it is BSI policy to supply theBSI implementation of those that have been published as British Standards,unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Eur

39、opean andinternational standards through its Library and its Technical Help to ExportersService. Various BSI electronic information services are also available whichgive details on all its products and services. Contact Information Centre. Tel:+44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subs

40、cribing members of BSI are kept up to date with standards developmentsand receive substantial discounts on the purchase price of standards. For detailsof these and other benefits contact Membership Administration. Tel: +44 (0)208996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online a

41、ccess to British Standards via British StandardsOnline can be found at http:/ information about BSI is available on the BSI website at http:/CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in theUK, of the publications of the international standardization bodies. E

42、xcept aspermitted under the Copyright, Designs and Patents Act 1988 no extract maybe reproduced, stored in a retrieval system or transmitted in any form or by anymeans electronic, photocopying, recording or otherwise without prior writtenpermission from BSI.This does not preclude the free use, in th

43、e course of implementing the standard,of necessary details such as symbols, and size, type or grade designations. Ifthese details are to be used for any other purpose than implementation then theprior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright and Licensing Manager.Tel: +44 (0)20 8996 7070 Email: