BS ISO 13012-2-2009 Rolling bearings - Accessories for sleeve type linear ball bearings - Boundary dimensions and tolerances for series 5《旋转轴承 套筒型线性滚珠轴承用附件 系列5用边界尺寸规格和公差》.pdf

《BS ISO 13012-2-2009 Rolling bearings - Accessories for sleeve type linear ball bearings - Boundary dimensions and tolerances for series 5《旋转轴承 套筒型线性滚珠轴承用附件 系列5用边界尺寸规格和公差》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 13012-2-2009 Rolling bearings - Accessories for sleeve type linear ball bearings - Boundary dimensions and tolerances for series 5《旋转轴承 套筒型线性滚珠轴承用附件 系列5用边界尺寸规格和公差》.pdf（24页珍藏版）》请在麦多课文档分享上搜索。

1、BS ISO13012-2:2009ICS 21.100.20NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDRolling bearings Accessories forsleeve type linear ballbearingsPart 2: Boundary dimensions andtolerances for series 5This British Standardwas published under theauthority of the Stand

2、ardsPolicy and StrategyCommittee on 31 August2009 BSI 2009ISBN 978 0 580 59015 3Amendments/corrigenda issued since publicationDate CommentsBS ISO 13012-2:2009National forewordThis British Standard is the UK implementation of ISO 13012-2:2009.The UK participation in its preparation was entrusted to T

3、echnicalCommittee MCE/7, Rolling bearings.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.Compliance with a Briti

4、sh Standard cannot confer immunityfrom legal obligations.BS ISO 13012-2:2009Reference numberISO 13012-2:2009(E)ISO 2009INTERNATIONAL STANDARD ISO13012-2First edition2009-02-01Rolling bearings Accessories for sleeve type linear ball bearings Part 2: Boundary dimensions and tolerances for series 5 Rou

5、lements Accessoires pour douilles billes linaires Partie 2: Dimensions dencombrement et tolrances pour la srie 5 BS ISO 13012-2:2009ISO 13012-2:2009(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shal

6、l not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area.

7、Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by I

8、SO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2009 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any fo

9、rm or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09

10、 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2009 All rights reservedBS ISO 13012-2:2009ISO 13012-2:2009(E) ISO 2009 All rights reserved iiiContents Page Foreword iv Introduction v 1 Scope . 1 2 Normative references . 1 3 Terms and definitions. 2 4 Symbols . 3 4.1 Clos

11、ed and adjustable flangeless housings for series 5 sleeve type linear ball bearings. 3 4.2 Open and open adjustable flangeless housings for series 5 sleeve type linear ball bearings . 3 4.3 Standard height shaft support rails for series 5 sleeve type linear ball bearings . 4 4.4 Flanged shaft suppor

12、t blocks for series 5 sleeve type linear ball bearings. 4 4.5 Solid and tubular shafts for series 5 sleeve type linear ball bearings 4 5 Housings 5 5.1 General. 5 5.2 Housings for series 5 sleeve type linear ball bearings. 5 6 Shaft support rails 5 7 Shaft support blocks 5 8 Shafts . 5 8.1 Material

13、5 8.2 Heat treatment. 5 8.3 Geometrical tolerances 6 9 Boundary dimensions and tolerances 6 9.1 Housings 6 9.2 Shaft support rails 9 9.3 Shaft support blocks 10 9.4 Shafts . 11 BS ISO 13012-2:2009ISO 13012-2:2009(E) iv ISO 2009 All rights reservedForeword ISO (the International Organization for Stan

14、dardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right

15、 to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International S

16、tandards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an

17、International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 13

18、012-2 was prepared by Technical Committee ISO/TC 4, Rolling bearings, Subcommittee SC 11, Linear motion rolling bearings. ISO 13012 consists of the following parts, under the general title Rolling bearings Accessories for sleeve type linear ball bearings: Part 1: Boundary dimensions and tolerances f

19、or series 1 and 3 Part 2: Boundary dimensions and tolerances for series 5 BS ISO 13012-2:2009ISO 13012-2:2009(E) ISO 2009 All rights reserved vIntroduction The use of sleeve type linear ball bearings can be facilitated by the selection of bearing housings, shafts, shaft support blocks and shaft supp

20、ort rails. These items, referred to as accessories, can aid in the application of the sleeve type linear ball bearings to achieve the desired criteria of smooth, accurate, low-friction linear motion free from chatter or stick-slip. The appropriate selection of bearing housing type, shaft and shaft s

21、upport should be established between the manufacturer and the user. This part of ISO 13012 was developed to be used with ISO 10285. BS ISO 13012-2:2009BS ISO 13012-2:2009INTERNATIONAL STANDARD ISO 13012-2:2009(E) ISO 2009 All rights reserved 1Rolling bearings Accessories for sleeve type linear ball

22、bearings Part 2: Boundary dimensions and tolerances for series 5 1 Scope This part of ISO 13012 specifies the boundary dimensions, other relevant dimensions and their tolerances of accessories for sleeve type linear ball bearings which are specified in ISO 10285. This part of ISO 13012 applies to: h

23、ousings closed and adjustable flangeless housings for series 5 sleeve type linear ball bearings, open and open adjustable flangeless housings for series 5 sleeve type linear ball bearings; shaft support rails standard height shaft support rails for series 5 sleeve type linear ball bearings; shaft su

24、pport blocks flanged shaft support blocks for series 5 sleeve type linear ball bearings; shafts solid and tubular shafts for series 5 sleeve type linear ball bearings. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated referenc

25、es, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 286-2, ISO system of limits and fits Part 2: Tables of standard tolerance grades and limit deviations for holes and shafts ISO 1132-1, Rolling bearings To

26、lerances Part 1: Terms and definitions ISO 1302, Geometrical Product Specifications (GPS) Indications of surface texture in technical product documentation ISO 3754, Steel Determination of effective depth of hardening after flame or induction hardening ISO 5593, Rolling bearings Vocabulary ISO 10285

27、:2007, Rolling bearings Sleeve type linear ball bearings Boundary dimensions and tolerances ISO 15241, Rolling bearings Symbols for quantities ISO 24393, Rolling bearings Linear motion rolling bearings Vocabulary BS ISO 13012-2:2009ISO 13012-2:2009(E) 2 ISO 2009 All rights reserved3 Terms and defini

28、tions For the purposes of this document, the terms and definitions given in ISO 1132-1, ISO 5593, ISO 10285, and ISO 24393 apply. 3.1 flangeless housing sleeve type linear ball bearing bearing housing which has a face with bolt holes or threaded holes for attachment to a support surface nominally pa

29、rallel to the bearing axis ISO 13012-1:2009 3.2 closed housing sleeve type linear ball bearing bearing housing in which the bearing seating is circumferentially continuous ISO 13012-1:2009 3.3 adjustable housing sleeve type linear ball bearing bearing housing with a longitudinal slit across its bear

30、ing seating which facilitates the mechanical adjustment of the bearing seating diameter ISO 13012-1:2009 3.4 open housing sleeve type linear ball bearing bearing housing with a longitudinal section removed to provide clearance over a shaft and support rail unit ISO 13012-1:2009 3.5 open adjustable h

31、ousing sleeve type linear ball bearing bearing housing which has the features of both open and adjustable sleeve type linear ball bearing housings ISO 13012-1:2009 3.6 shaft support rail longitudinal pedestal which provides continuous support to a shaft NOTE Shaft support rails may be used with open

32、 sleeve type linear ball bearings. ISO 13012-1:2009 3.7 shaft support block block which provides support to a shaft NOTE Shaft support blocks are normally used to support the shaft at its ends and can be used with closed sleeve type, adjustable sleeve type or open sleeve type linear ball bearings. I

33、SO 13012-1:2009 3.8 shaft basically cylindrical rod along which a linear ball bearing traverses ISO 13012-1:2009 BS ISO 13012-2:2009ISO 13012-2:2009(E) ISO 2009 All rights reserved 34 Symbols For the purposes of this document, the symbols given in ISO 15241 and the following apply. The symbols (exce

34、pt those for tolerances) shown in Figures 1 to 5, and the values given in Tables 1 to 6 denote nominal dimensions unless specified otherwise. NOTE Figures 1 to 5 are drawn schematically and do not necessarily show all design details. 4.1 Closed and adjustable flangeless housings for series 5 sleeve

35、type linear ball bearings See Table 1 and Figure 1. A (overall) width Daseating diameter Fwbore diameter of ball complement of sleeve type linear ball bearing (reference) G designation of screw thread of attachment hole H distance from mounting face to centreline of seating diameter H1(overall) heig

36、ht J centre distance between bolt holes (length) J1centre distance between bolt holes (width) L length of housing L1distance from side face to centreline of seating diameter N diameter of bolt hole 4.2 Open and open adjustable flangeless housings for series 5 sleeve type linear ball bearings See Tab

37、le 2 and Figure 2. A (overall) width Daseating diameter E width of sector opening (at diameter Da) Fwbore diameter of ball complement of sleeve type linear ball bearing (reference) G designation of screw thread of attachment hole H distance from mounting face to centreline of seating diameter H1(ove

38、rall) height J centre distance between bolt holes (length) J1centre distance between bolt holes (width) L length of housing L1distance from side face to centreline of seating diameter angle of sector opening BS ISO 13012-2:2009ISO 13012-2:2009(E) 4 ISO 2009 All rights reserved4.3 Standard height sha

39、ft support rails for series 5 sleeve type linear ball bearings See Table 3 and Figure 3. A (overall) width d outside diameter of shaft (reference) H distance from mounting face to centreline of shaft H1height of flange J centre distance between bolt holes (length) J1centre distance between bolt hole

40、s (width) M width of shaft support N diameter of bolt hole N1diameter of bolt hole (shaft attachment) angle of shaft support 4.4 Flanged shaft support blocks for series 5 sleeve type linear ball bearings See Table 4 and Figure 4. A (overall) width Daseating diameter H distance from mounting face to

41、centreline of seating diameter H1height of flange H2(overall) height J centre distance between bolt holes (length) L length of base N diameter of bolt hole 4.5 Solid and tubular shafts for series 5 sleeve type linear ball bearings See Tables 5 and 6, and Figure 5 d outside diameter of shaft dssingle

42、 outside diameter of shaft L length of shaft Lsactual length of shaft t straightness of shaft Vdmpvariation of mean outside diameter of shaft Vdspvariation of outside diameter of shaft in a single plane dsdeviation of a single outside diameter of shaft Lsdeviation of the actual length of shaft BS IS

43、O 13012-2:2009ISO 13012-2:2009(E) ISO 2009 All rights reserved 55 Housings 5.1 General To facilitate the design and assembly of sleeve type linear ball bearings, specifically designed housings are available. Included in this part of ISO 13012 are the boundary dimensions and other related dimensions

44、of sleeve type linear ball bearings series 5 as specified in ISO 10285:2007. The housings specified in Tables 1 and 2, and the corresponding sleeve type linear ball bearings should be supplied by the same producer. The reason for this is that the fixation of the bearings in the housings is specified

45、 by the producer and is not covered by this part of ISO 13012. 5.2 Housings for series 5 sleeve type linear ball bearings This part of ISO 13012 includes the following housing designs for series 5 linear ball bearings: closed and adjustable flangeless housings for series 5 sleeve type linear ball be

46、arings (Table 1); open and open adjustable flangeless housings for series 5 sleeve type linear ball bearings (Table 2). 6 Shaft support rails This part of ISO 13012 includes the following shaft support rails for sleeve type linear ball bearings: standard height shaft support rails for series 5 sleev

47、e type linear ball bearings (Table 3). 7 Shaft support blocks This part of ISO 13012 includes the following shaft support blocks for sleeve type linear ball bearings: flanged shaft support blocks for series 5 sleeve type linear ball bearings (Table 4). 8 Shafts 8.1 Material Shafts covered by this pa

48、rt of ISO 13012 are precision hardened and ground steel shafts in both solid and tubular section. They are manufactured from high quality carbon steel or high quality carbon chrome steel and are either surface hardened or through hardened. 8.2 Heat treatment 8.2.1 Surface hardened shafts The cylindr

49、ical surface of the shafts is heat treated to provide a basically uniform effective depth of hardening and a surface hardness of not less than 653 HV (58 HRC) over the entire operating length. The effective depth of hardening shall be determined in accordance with ISO 3754. This effective depth of hardening is the distance from the outside surface of the shaft to a material layer at which the hardness is approximately 80 % of the specified minimum surface