BS ISO 12742-2007 Copper lead and zinc sulfide concentrates - Determination of transportable moisture limits - Flow-table method《铜、铅和硫化锌精矿 传送过程中湿度范围的测定 流度台法》.pdf

《BS ISO 12742-2007 Copper lead and zinc sulfide concentrates - Determination of transportable moisture limits - Flow-table method《铜、铅和硫化锌精矿 传送过程中湿度范围的测定 流度台法》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 12742-2007 Copper lead and zinc sulfide concentrates - Determination of transportable moisture limits - Flow-table method《铜、铅和硫化锌精矿 传送过程中湿度范围的测定 流度台法》.pdf（28页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS ISO 12742:2007Copper, lead, and zinc sulfide concentrates Determination of transportable moisture limits Flow-table methodICS 73.060.99g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55

2、g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS ISO 12742:2007This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 August 2007 BSI 2007ISBN 978 0 580 56423 9National forewordThis British Standard is the UK implementation of ISO 12742:2

3、007. The UK participation in its preparation was entrusted to Technical Committee NFE/36, Copper, lead and zinc ores and concentrates.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provi

4、sions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.Amendments issued since publicationAmd. No. Date CommentsReference numberISO 12742:2007(E)INTERNATIONAL STANDARD ISO12742Second edition2007-07-01Cop

5、per, lead, and zinc sulfide concentrates Determination of transportable moisture limits Flow-table method Concentrs sulfurs de cuivre, de plomb et de zinc Dtermination des limites dhumidit transportable Mthode de la table dcoulement BS ISO 12742:2007ii iiiContents Page Foreword iv Introduction v 1 S

6、cope 1 2 Normative references 1 3 Principle1 4 Apparatus .1 5 Sampling and sample preparation.2 5.1 General2 5.2 Laboratory sample.3 5.3 Sample preparation .3 6 Procedure .3 6.1 General3 6.2 Preparation of test portions4 6.2.1 General4 6.2.2 Filling the mould 4 6.2.3 Tamping pressure4 6.2.4 Tamping

7、procedure .5 6.2.5 Removal of the mould .5 6.2.6 Dropping the flow table.5 6.3 Identification of the flow state5 6.4 Preliminary flow moisture point.7 6.4.1 Preparation of test portion7 6.4.2 Determination of preliminary flow moisture point .7 6.4.3 Addition of water for preliminary flow moisture po

8、int test .8 6.5 Main flow moisture point determination .8 6.5.1 Preparation of test portions8 6.5.2 Determination of main flow moisture point 8 6.5.3 Addition of water for main flow moisture point determination.8 6.6 Graphical method 8 6.6.1 Preparation of test portions8 6.6.2 Determination of flow

9、moisture point9 6.7 Moisture determination .9 7 Expression of results 9 7.1 Main flow moisture point 9 7.2 Flow moisture point determined by the graphical method .9 8 Validation of main flow moisture point .10 9 Test report 10 Annex A (normative) Description of equipment used to determine TML11 Bibl

10、iography 18 BS ISO 12742:2007iv Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body inter

11、ested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical

12、 Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the te

13、chnical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. IS

14、O shall not be held responsible for identifying any or all such patent rights. ISO 12742 was prepared by Technical Committee ISO/TC 183, Copper, lead, zinc and nickel ores and concentrates. This second edition cancels and replaces the first edition (ISO 12742:2000), which has been technically revise

15、d. BS ISO 12742:2007vIntroduction ISO 12742:2000 was published as a guidance document because there had been insufficient test programme participants to allow precision data to be derived. However, it had been agreed that ISO/TC 183/WG 11 be kept in existence, as there was likelihood that a precisio

16、n test programme could be held at a later time. Revision of ISO 12742 was commenced in 2005, on the basis that changes to the procedure were necessary, and there were then sufficient participants to allow a test programme to be conducted. In the final analysis, insufficient participants were identif

17、ied. However, the International Standard has been revised for a further edition as a guidance document. BS ISO 12742:2007blank1Copper, lead, and zinc sulfide concentrates Determination of transportable moisture limits Flow-table method WARNING This International Standard may involve hazardous materi

18、als, operations and equipment. It is the responsibility of the user of this International Standard to establish appropriate health and safety practices and determine the applicability of regulatory limitations prior to use. 1 Scope This International Standard specifies a flow-table method for the de

19、termination of the transportable moisture limit (TML) of copper, lead and zinc sulfide concentrates, which may liquefy during transport. This International Standard is applicable to the determination of the TML of concentrates containing 10 % to 80 % (mass fraction) of lead, or 10 % to 65 % (mass fr

20、action) of zinc, or 10 % to 55 % (mass fraction) of copper. It is applicable to TMLs in the range 3 % to 28 % (mass fraction). 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For u

21、ndated references, the latest edition of the referenced document (including any amendments) applies. ISO 10251, Copper, lead, zinc and nickel concentrates Determination of mass loss of bulk material on drying ISO 12743, Copper, lead, zinc and nickel concentrates Sampling procedures for determination

22、 of metal and moisture content 3 Principle The moisture content of the sample is adjusted by mixing with water. The mixture is converted to a conical shape using a mould and tamper. The sample is placed on the flow table and the mould is removed. The flow characteristics are determined by repeated d

23、ropping of the flow table, while observing the behaviour of the sample. When sufficient water has been added to the sample so that plastic deformation occurs during the dropping of the flow table, the sample is considered to be at its flow moisture point. The TML is calculated as 90 % of the flow mo

24、isture point. 4 Apparatus Copper, lead and zinc concentrates may gain or lose moisture rapidly when exposed to air. The laboratory should be designed so that excessive temperatures, direct sunlight, air currents and humidity variations are avoided. 4.1 Flow table and frame, as specified in Annex A.

25、The flow-table mounting shall be as specified in Figure A.1. BS ISO 12742:20072 4.2 Mould, as specified in Figure A.1. 4.3 Tamper. The required tamping pressure may be achieved by using calibrated, spring-loaded tampers or some other suitable design of tamper that allows a controlled pressure to be

26、applied via a 30 mm diameter tamper head as specified in Figure A.2. 4.4 Calliper ruler. 4.5 Balance, top loading, having the sensitivity specified in Table 1. Table 1 Sensitivity of balance and precision of weighing Mass of sample plus tray g Precision of balance and weighing g 100 200 300 400 500

27、0,01 0,02 0,03 0,04 0,05 4.6 Measuring cylinder, of capacity 50 ml to 200 ml. 4.7 Burette, of capacity 10 ml. 4.8 Mixing bowl, hemispherical, of diameter approximately 30 cm. NOTE It is advisable to use an automatic mechanical mixer having a mixing bowl as described, as this leads to improved precis

28、ion. 4.9 Rubber gloves. 4.10 Drying trays or pans, having dimensions that permit the sample to be spread to a thickness of less than 30 mm. The trays shall be made of corrosion-resistant and heat-resistant material, such as stainless steel, glass or enamel plate. 4.11 Drying oven, ventilated, with f

29、orced circulation of air or inert gas, regulated at a temperature of 105 C 5 C. 4.12 Airtight containers. 5 Sampling and sample preparation 5.1 General TML figures are required to be updated on a periodic basis, usually six monthly, or when there is a known change to the process used to produce the

30、material. The reported figure should be the mean of samples taken during the period. BS ISO 12742:20073To ensure that the TML result is representative, increments of the material shall be taken either a) while a stockpile is being built up or broken down, or b) while loading or discharging a vessel.

31、 These increments are combined to form the sample used to determine TML. The sample used to determine TML should not be used to determine moisture. Stationary sampling of stockpiles should never be used for the determination of TML. This method of sampling can only be used to provide an indicative m

32、oisture value for use during the planning of shipping schedules. 5.2 Laboratory sample Samples for the determination of TML shall be taken in accordance with ISO 12743. The laboratory sample shall not weigh less than 12 kg. To minimize changes to the flow characteristics of the sample, it shall not

33、be oven dried or ground during its preparation. 5.3 Sample preparation Homogenize the laboratory sample as quickly as possible to prevent losses. Take nine test samples as follows: a) Sample 1 Take not less than 1 kg, which is to be used for determining the moisture content of the sample “as receive

34、d”, from the laboratory sample and place on a drying tray or pan. b) Sample 2 Take approximately 1,2 kg from the laboratory sample. This sample is to be used for the preliminary TML test. Store this sample in an appropriately labelled airtight container. c) Samples 3 to 6 Take four samples of approx

35、imately 1,2 kg from the laboratory sample. These samples are to be used for the main TML test. Store these samples in appropriately labelled airtight containers. d) Samples 7 to 9 Take three samples of approximately 1,2 kg from the laboratory sample. These samples are to be used for confirmation of

36、TML by the graphical method. Store these samples in appropriately labelled airtight containers. 6 Procedure 6.1 General Copper, lead and zinc concentrates may undergo rapid changes in moisture when exposed to air, so all stages of the test should be accomplished in the shortest time period and shall

37、 definitely be completed within the day of commencement. Where possible, sample containers should be covered with plastic film or any other suitable airtight cover. The moisture result from Sample 1 provides information about how far the material under test is from the flow moisture point. BS ISO 12

38、742:20074 As more accurate results are obtained when the moisture of the test portion is close to the flow moisture point, a preliminary test is carried out (Sample 2). The result of this test is used to adjust the moisture of the final test portion to 1 % to 2 % below (Samples 3 and 4) and above (S

39、amples 5 and 6) the flow moisture point. To check the main flow moisture point graphically, three more samples (Samples 7 to 9), having moisture values higher than the flow moisture point, are tested. The flow moisture point is the extrapolation to zero of the linear adjustment of the seven test por

40、tions. The value obtained this way will be used to validate the main flow moisture point. 6.2 Preparation of test portions 6.2.1 General Sample 1 is prepared in accordance with ISO 10251. Proceed to 6.7. Samples 2 to 9 are prepared in accordance with 6.2.2 to 6.2.6. 6.2.2 Filling the mould Place the

41、 mould on the centre of the flow table and fill it in three stages with the test portion as follows: a) the first charge, after tamping, shall aim to fill the mould to approximately one-third of its depth; b) the second charge, after tamping, shall fill the mould to about two-thirds of its depth; c)

42、 the third and final charge, after tamping, shall reach to just below the top of the mould (see Figure 1). The quantity of test portion required to achieve each of these stages will vary from one material to another, but is readily established after experience has been gained on the packing characte

43、ristics of the material being tested. 6.2.3 Tamping pressure The aim of tamping is to simulate the amount of compaction prevailing at the bottom of a shipboard cargo for the material being tested. The correct pressure to be applied via the tamper is calculated as follows: TDmaxp dg= (1) where pTis t

44、he tamping pressure, in pascals; Dis the bulk density, in kilograms per cubic metre; dmaxis the maximum depth of the cargo, in metres; g is the acceleration due to gravity (= 9,81 m/s2). If, when calculating the tamping pressure, there is no information available concerning the cargo depth, use the

45、maximum likely depth. Alternatively, the pressure may be estimated from Table 2. BS ISO 12742:20075Table 2 Tamping pressures (kPa) for selected concentratesaTypical concentrate type Bulk density kg/m3Maximum cargo depth 2 m 5 m 10 m 20 m Copper 2 000 39 2,8 98 6,9 196 13,9 392 27,7 Lead 2 100 41 2,9

46、 103 7,3 206 14,6 412 29,1 Zinc 1 950 38 2,7 96 6,8 192 13,5 384 27,1 aValues in square brackets are equivalent kilogram-force (kgf) when applied via a 30 mm diameter tamper head. 6.2.4 Tamping procedure The number of tamping actions (applying the correct, steady pressure each time) should be about

47、35 for the bottom layer, 25 for the middle layer and 20 for the top layer. Tamping shall be performed successively over the complete area, including the edges of the sample, to form a uniform surface for each layer (see Figure 1). 6.2.5 Removal of the mould Tap the mould on its side until it becomes

48、 loose, leaving the material in the shape of a truncated cone on the flow table. Clean the surface of the table around the cone. Measure the size of the cone in the three directions marked on the table. The average of these readings will be equivalent to zero displacement. 6.2.6 Dropping the flow ta

49、ble Immediately after removing the mould, raise and drop the flow table up to 50 times through a height of 12,5 mm 0,13 mm at a rate of 25 times per minute. While the flow table is going through these cycles, observe the behaviour of the material using the information provided in 6.3 as a guide for determining the flow state. 6.3 Identification of the flow state The impacting action of the flow table causes the grains of the material to rearrange themselves to produce compaction of the mass. As a result, the fixed volume of