BS ISO 12302-2017 Plain bearings Quality characteristics Statistical process control (SPC)《滑动轴承 质量特定 统计过程控制(SPC)》.pdf

《BS ISO 12302-2017 Plain bearings Quality characteristics Statistical process control (SPC)《滑动轴承 质量特定 统计过程控制(SPC)》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 12302-2017 Plain bearings Quality characteristics Statistical process control (SPC)《滑动轴承 质量特定 统计过程控制(SPC)》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BS ISO 12302:2017Plain bearings Qualitycharacteristics Statisticalprocess control (SPC)BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS ISO 12302:2017 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 12302:2017. It supersedes B

2、S 7762:1994 which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee MCE/12, Plain bearings.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisio

3、ns of a contract. Users are responsible for its correct application. The British Standards Institution 2017.Published by BSI Standards Limited 2017ISBN 978 0 580 92970 0 ICS 21.100.10 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published

4、 under the authority of the Standards Policy and Strategy Committee on 31 March 2017.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dBS ISO 12302:2017 ISO 2017Plain bearings Quality characteristics Statistical process control (SPC)Paliers lisses Caractristiques de qualit Co

5、ntrle statistique du procd (CSP)INTERNATIONAL STANDARDISO12302Second edition2017-03Reference numberISO 12302:2017(E)BS ISO 12302:2017ISO 12302:2017(E)ii ISO 2017 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2017, Published in SwitzerlandAll rights reserved. Unless otherwise specified, no part

6、 of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member bod

7、y in the country of the requester.ISO copyright officeCh. de Blandonnet 8 CP 401CH-1214 Vernier, Geneva, SwitzerlandTel. +41 22 749 01 11Fax +41 22 749 09 47copyrightiso.orgwww.iso.orgBS ISO 12302:2017ISO 12302:2017(E)Foreword iv1 Scope . 12 Normative references 13 Terms and definitions . 14 SPC met

8、hods 15 Selection of SPC quality characteristics 16 Geometric quality characteristics 27 Material quality characteristics 4 ISO 2017 All rights reserved iiiContents PageBS ISO 12302:2017ISO 12302:2017(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of nat

9、ional standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. Interna

10、tional organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those inten

11、ded for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www

12、.iso .org/ directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document

13、 will be in the Introduction and/or on the ISO list of patent declarations received (see www .iso .org/ patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the voluntary nature of standards, the

14、 meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www .iso .org/ iso/ foreword .html.This document was prepared

15、by Technical Committee ISO/TC 123, Plain bearings, Subcommittee SC 5, Quality analysis and assurance.This second edition cancels and replaces the first edition (ISO 12302:1993), which has been technically revised.iv ISO 2017 All rights reservedBS ISO 12302:2017INTERNATIONAL STANDARD ISO 12302:2017(E

16、)Plain bearings Quality characteristics Statistical process control (SPC)1 ScopeThis document specifies for plain bearings (except thick-walled half-bearings) those quality characteristics in accordance with ISO 12301 which can be used to regulate and control a production process on the basis of sta

17、tistical process control (SPC).It covers dimensional variables but does not take account of attributes.2 Normative referencesThe following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the e

18、dition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 12301, Plain bearings Quality control techniques and inspection of geometrical and material quality characteristics3 Terms and definitionsFor the purposes of this docume

19、nt, the following definitions apply.ISO and IEC maintain terminological databases for use in standardization at the following addresses: IEC Electropedia: available at h t t p :/ www .electropedia .org/ ISO Online browsing platform: available at h t t p :/ www .iso .org/ obp3.1quality characteristic

20、characteristic by means of which the quality of a plain bearing is assessed3.2statistical process control SPCcontrol of quality characteristics of plain bearings during the production process by means of statistical techniques in order to comply with quality requirements4 SPC methodsThe applied stat

21、istical methods used to achieve control of a production process may be different and thus are to be agreed upon between the manufacturer and customer.5 Selection of SPC quality characteristicsDepending on the intended purpose, function, etc. of the plain bearings to be used, the manufacturer and cus

22、tomer shall select and stipulate the particular characteristics for SPC according to Clause 6.It should be noted that the designated characteristics in the matrix of Clause 6 have been prepared as a guide. ISO 2017 All rights reserved 1BS ISO 12302:2017ISO 12302:2017(E)6 Geometric quality characteri

23、sticsThe quality characteristics are classified into three groups: preferred, optional or unsuitable.Following the order of the specified characteristics in accordance with ISO 12301, these quality characteristics are listed in the form of a matrix as:preferred with “yes”;optional with “(yes)”;unsui

24、table with “no”;not relevant with “”.Those quality characteristics which are marked with “(yes)” and “no” are accompanied by an explanation in the column “remarks” in Table 1.A horizontal dash () in a column means that this characteristic is not relevant for the specific type of plain bearing.Table

25、1 Geometric quality characteristicsSubclause No. (accord-ing to ISO 12301)Quality character-isticType of plain bearingRemarksThin-walled halfbear-ingWrapped bushUnsplit metal-lic bushSolid poly-mer bushSin-tered bushThrust washer (ring and half)a b c d e f6.1Wall thickness6.1.1Line measurementno no

26、no no no a and b to e: There is an unlimited number of values on a single measuring line ranging between minimum and maximum6.1.2Point measurement (defined)yes (yes) yes yes (yes) yesb: Only where it is possible to measure at prede-termined pointse: For closed tolerance requirement, 100 % grading ma

27、y be requested as an alternative to SPC6.2Outside diameter yes yes yes yes (yes)f: Blanking tool; tool checking by means of initial product acceptance with each order2 ISO 2017 All rights reservedBS ISO 12302:2017ISO 12302:2017(E)Subclause No. (accord-ing to ISO 12301)Quality character-isticType of

28、plain bearingRemarksThin-walled halfbear-ingWrapped bushUnsplit metal-lic bushSolid poly-mer bushSin-tered bushThrust washer (ring and half)a b c d e f6.3Inside diameter (yes) yes yes yes (yes)b: Normally determined by wall thickness and outside diameterf: Blanking tool; tool checking by means of in

29、itial product acceptance with each order6.4 Width (yes) (yes) (yes) (yes) (yes) a and b to e: Not a primary charac-teristic6.5Locating featuresno noa and f: Are only locating aids6.6Lubricant feed and distribution featuresno no no no noa, b to d and f: Not a primary characteristic6.7Surface conditio

30、nsno no no no no noa and b to f: No Gaussian distribu-tion of measured values6.8 Crush height yes 6.9 Free spread (yes) a: Not a primary characteristic6.10Straightness of sliding surfaceno a: Graphical evaluation in most cases6.11Joint face taper(yes) a: Not a primary characteristic6.12Back contact

31、(proportion of surface area)no a: Attribute (qualitative) characteristic6.13Joint displacement (yes) b: Will be adjusted when fitting the bush into the housing bore; attribute charac-teristic6.14Height of thrust half-washer (thickness) (yes)f: Blanking tool; tool checking by means of initial product

32、 acceptance with each order6.15 Flatness no f: Attribute (qualitative) characteristicTable 1 (continued) ISO 2017 All rights reserved 3BS ISO 12302:2017ISO 12302:2017(E)Subclause No. (accord-ing to ISO 12301)Quality character-isticType of plain bearingRemarksThin-walled halfbear-ingWrapped bushUnspl

33、it metal-lic bushSolid poly-mer bushSin-tered bushThrust washer (ring and half)a b c d e f6.16 Flange diameter(yes) (yes) (yes) (yes) (yes) a and b to e: Not a primary charac-teristic6.17 Distance between flanges(yes) (yes) (yes) (yes) (yes) a and b to e: Not a primary characteristic6.18 Flange thic

34、kness(yes) (yes) (yes) (yes) (yes) a and b to e: Measuring point shall be defined6.19 Perpen-dicularity (squareness) of flange(yes) (yes) (yes) (yes) (yes) a and b to e: Not a primary characteristic6.20 Geometric deviations (yes) (yes) (yes) c, d and e: Not a primary characteristic7 Material quality

35、 characteristicsControl of the material manufacturing processes depends on a large number of parameters which involve “process-knowledge”. The manufacturer shall decide which parameters are to be checked using statistical techniques in accordance with customer requirements.Table 1 (continued)4 ISO 2

36、017 All rights reservedBS ISO 12302:2017BS ISO 12302:2017ISO 12302:2017(E) ISO 2017 All rights reservedICS 21.100.10Price based on 4 pagesThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and se

37、rvices.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)About usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience an

38、d expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information o

39、n standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, includin

40、g British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.Copyright in BSI pub

41、licationsAll the content in BSI publications, including British Standards, is the property of and copyrighted by BSI or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercia

42、l publication and use.Save for the provisions below, you may not transfer, share or disseminate any portion of the standard to any other person. You may not adapt, distribute, commercially exploit, or publicly display the standard or any portion thereof in any manner whatsoever without BSIs prior wr

43、itten consent.Storing and using standardsStandards purchased in soft copy format: A British Standard purchased in soft copy format is licensed to a sole named user for personal or internal company use only. The standard may be stored on more than 1 device provided that it is accessible by the sole n

44、amed user only and that only 1 copy is accessed at any one time. A single paper copy may be printed for personal or internal company use only.Standards purchased in hard copy format: A British Standard purchased in hard copy format is for personal or internal company use only. It may not be further

45、reproduced in any format to create an additional copy. This includes scanning of the document.If you need more than 1 copy of the document, or if you wish to share the document on an internal network, you can save money by choosing a subscription product (see Subscriptions).Reproducing extractsFor p

46、ermission to reproduce content from BSI publications contact the BSI Copyright & Licensing team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have

47、instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, b

48、oth in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing

49、 Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further inf