BS ISO 11901-2-2004 Tools for pressing - Gas springs - Specification of accessories《冲压工具 气压弹簧 附件的规范》.pdf

《BS ISO 11901-2-2004 Tools for pressing - Gas springs - Specification of accessories《冲压工具 气压弹簧 附件的规范》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 11901-2-2004 Tools for pressing - Gas springs - Specification of accessories《冲压工具 气压弹簧 附件的规范》.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS ISO 11901-2:2004 Tools for pressing Gas springs Part 2: Specification of accessories ICS 25.120.10 SITIRBDRADNATS H SB SIO 10911-4002:2 gnisserp rof slooT sgnirps saG raPcepS :2 ticifaitno ca foossecirse SCI 01.021.52 BS ISO 11901-2:2004 This British Standard was published under

2、the authority of the Standards Policy and Strategy Committee on 22 April 2004 BSI 22 April 2004 ISBN 0 580 43655 1 National foreword This British Standard reproduces verbatim ISO 11901-2:2004 and implements it as the UK national standard. The UK participation in its preparation was entrusted to Tech

3、nical Committee MTE/12, Tools for pressing and moulding, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international publications referred to in this document

4、may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. User

5、s are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change,

6、 and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the ISO title page, pages ii to v, a blank page, pages 1 to 10 and a back cover. The BSI copyrigh

7、t notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date CommentsINTERNATIONAL STANDARD ISO 11901-2 Second edition 2004-04-01 Reference number ISO 11901-2:2004(E) OSI 2004 Tools for pressing Gas springs Part 2: Specification o

8、f accessories Outillage de presse Ressorts gaz Partie 2: Spcifications des accessoiresBSISO119012:2004ISO -10911:2)E(4002 ii ISO 4002 All rithgs reresvde id FDPscalimer ThFDP si fam eliy ctnome niat deddebyepfa.sec In cacnadrociw eth sebodA sneciliycilop gn, thf siam elirp eb ytnide or viewb detu ll

9、ahs ton tide ebed lnuet sst ehyfepcaa hcihw serdebme et desnecil era dedo tsni dnat no dellahpmoc eturep reformign ttide ehign. In odt gnidaolnwhsi liferap ,ticca setpe trehnie snopser ehtibtiliy fo not fnirA gnigniycilop gnisnecil sebod. Teh SItneC Olar Seerctraiat catpecs ibail ontily t nih.aera s

10、i Aebod t a sirramedak fo AsyS ebodtmeI snocrropta.de teDalis fo tfos ehtwcudorp erats t desuo taerct ehsi FDP fb nac elie ft ni dnuoG ehreneI lanfo relative to tf eh;eli tP ehDF-rctaenoi temaraptpo erew sremizif deorp rinti.gn Evrey t neeb sah eracakt neo rusnee ttah tf ehtius si elibaf elosu re by

11、 ISO memdob rebsei. In eht kilnuyle evtne ttah a borplem retalit gno it si f,dnuo esaelp inform thtneC eral ceSrteraiat ta teh sserdda vigoleb new. IOS 4002 Alr lithgs reresv.de sselnU toesiwreh sficep,dei rap ont fo thbup silitaciam nocudorper eb yde or tuilidez na nif yorm ro by nam ysnae, tcelerm

12、 ro cinoecinahcal, tohp gnidulcnicopom dna gniyicrfomli, tiwuoht repsimsi noin wrtif gnirtie mohI reSO ta the asserdd ebwol or ISOmem sreb obyd t nitnuoc ehry fo teh euqertsre. SIc Oopyright ofifce saCe soptael 65 -HCG 1121eneva 02 Te.l 22 14 + 10 947 11 Fax + 22 14 0 9479 74 Eam-il ocpyrithgios.ogr

13、 Web wwwi.soo.rg Pubni dehsil Stiwrezldna BSISO119012:2004OSI -109114002:2)E( ISO 4002 r llAithgs reservde iii Contents Page 1 Scope 1 2 Normative references 1 3 Dimensions 2 3.1 Type A1 Mounting base plates with two holes to clamp the gas spring . 2 3.2 Type A2 Mounting base plates with four holes

14、to clamp the gas spring 3 3.3 Type B Two part mounting clamps 4 3.4 Type C Flange mounts 5 3.5 Type D Front end supports 8 3.6 Type E Rectangular flange mounts . 9 4 Material . 9 5 Designation 10 BSISO119012:2004ISO -10911:2)E(4002 iv ISO 4002 All rithgs reresvde Foreword ISO (the International Orga

15、nization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been establis

16、hed has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization

17、. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. P

18、ublication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such pate

19、nt rights. ISO 11901-2 was prepared by Technical Committee ISO/TC 29, Small tools, Subcommittee SC 8, Tools for pressing and moulding. This second edition cancels and replaces the first edition (ISO 11901-2:1995), which has been technically revised. ISO 11901 consists of the following parts, under t

20、he general title Tools for pressing Gas springs: Part 1: General specifications Part 2: Specification of accessories BSISO119012:2004OSI -109114002:2)E( ISO 4002 r llAithgs reservde v Introduction The attention of the user of ISO 11901 is drawn to the fact that gas springs will have to conform to th

21、e users national regulations. BSISO119012:2004. iv BSISO119012:2004ANRETNIITOTS LANDNADRA OSI -109114002:2)E( ISO 4002 r llAithgs reservde 1 Tools for pressing Gas springs Part 2: Specification of accessories 1S c o p e This part of ISO 11901 specifies the dimensions, in millimetres, of mounting bas

22、e plates, of two-part mounting clamps, of flange mounts and of front end supports intended for use in press tools together with gas springs in accordance with ISO 11901-1. It also gives information concerning materials and specifies the designation of the mounting accessories in accordance with this

23、 part of ISO 11901. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 63

24、0, Structural steels Plates, wide flats, bars, sections and profiles ISO 2768-1, General tolerances Part 1: Tolerances for linear and angular dimensions without individual tolerance indications ISO 11901-1, Tools for pressing Gas springs Part 1: General specifications BSISO119012:2004ISO -10911:2)E(

25、4002 2 ISO 4002 All rithgs reresvde 3 Dimensions 3.1 Type A1 Mounting base plates with two holes to clamp the gas spring See Figure 1 and Table 1. General tolerance: ISO 2768-m Figure 1 Mounting base plates Type A1 Table 1 Dimensions of mounting base plates Type A1 Mount for gas spring type 5 000 70

26、 50 20 20 15 15 9 9 14 12 7 500 75 56,5 20 20 15 15 9 9 14 12 ABD 2 EG 1 G 2 H 1 H 2 L 1 L 2 0 0,1 BSISO119012:2004OSI -109114002:2)E( ISO 4002 r llAithgs reservde 3 3.2 Type A2 Mounting base plates with four holes to clamp the gas spring See Figure 2 and Table 2. General tolerance: ISO 2768-m Figur

27、e 2 Mounting base plates Type A2 Table 2 Dimensions of mounting base plates Type A2 Mount for gas spring type 15000 100 73,5 40 20 15 18 9 11 14 12 30000 120 92 60 20 15 20 9 13,5 14 13 50000 140 109,5 80 20 18 20 11 13,5 15 13 75000 190 138 100 25 18 26 11 17,5 15 17 100000 210 170 120 25 20 26 13,

28、5 17,5 13 17 ABD 2 EG 1 G 2 H 1 H 2 L 1 L 2 0 0,1 BSISO119012:2004ISO -10911:2)E(4002 4 ISO 4002 All rithgs reresvde 3.3 Type B Two part mounting clamps See Figure 3 and Table 3. General tolerance: ISO 2768-m Figure 3 Two part mounting clamps Type B Table 3 Dimensions of two part mounting clamps Typ

29、e B Mount for gas spring type 1500 50 35 32,528,5 6,6 4 7 5 2500 55 40 38,534,5 6,6 4 7 5 5000 70 50 45,540,5 9 4 7 20 7500 75 56,550,544,5 9 8 12 24 15000 100 73,5 75,5 68,5 11 8 12 24 30000 120 92 95,5 88,5 13,5 8 12 24 50000 140 109,5120,5113,513,5 8 12 24 75000 190 138 150,5143,517,5 8 12 24 100

30、000 210 170 195,5 188 17,5 8 13 24 ABCDEFHJ 0 0,1 0 0,1 BSISO119012:2004OSI -109114002:2)E( ISO 4002 r llAithgs reservde 5 3.4 Type C Flange mounts 3.4.1 Type C1 Cylindrical flange mounts See Figure 4 and Table 4. General tolerance: ISO 2768-m The two flange halves shall be held together with assemb

31、ly screws. Key 1 plain ring 2 assembly screws Figure 4 Cylindrical flange mounts Type C1 BSISO119012:2004ISO -10911:2)E(4002 6 ISO 4002 All rithgs reresvde 3.4.2 Type C2 Square flange mounts See Figure 5 and Table 4. General tolerance: ISO 2768-m The two flange halves are to be held together with as

32、sembly screws. Key 1p l a i n r i n g 2 assembly screws Figure 5 Square flange mounts Type C2 BSISO119012:2004OSI -109114002:2)E( ISO 4002 r llAithgs reservde 7 3.4.3 Mounting of the flange mounts types C1 and C2 on gas springs See Figure 6 and Table 4. General tolerance: ISO 2768-m Figure 6 Mountin

33、g of a flange mount Table 4 Dimensions of flange mounts Types C1 and C2 Mount for gas spring Reference of mount type h10 1 500 32,5 35 9 60 - 2 6,6 34 17 C1 2 500 38,5 40 9 68 52 2 6,6 40 17 C1 and C2 5 000 45,5 50 13 86 64 2 9 47 23 C1 and C2 7 500 50,5 56,5 13 95 70 4 9 54 24 C1 and C2 15 000 75,5

34、 73,5 16 122 90 5 11 80 29 C1 and C2 30 000 95,5 92 18 150 110 5 13,5 100 33 C1 and C2 50 000 120,5 109,5 21 175 130 5 13,5 125 36 C1 and C2 75 000 150,5 138 27 220 162 5 17,5 155 41 C1 and C2 100 000 195,5 170 27 290 210 5 17,5 200 47 C1 and C2 ABCD 1 D 2 D 3 EFJ 0,1 +0,1 0,3 BSISO119012:2004ISO -1

35、0911:2)E(4002 8 ISO 4002 All rithgs reresvde 3.5 Type D Front end supports See Figure 7 and Table 5. General tolerance: ISO 2768-m Key 1s c r e w Figure 7 Front end supports Type D Table 5 Dimensions of front end supports Type D Mount for gas spring Screw 7500 50 5011060130 9 80 90 40 M84037,5 15 00

36、0 75 63,5 137 75 160 11 105 115 52,5 M10 52,5 50 30 000 95 80 170 92,5 195 13,5 125 145 67,5 M12 62,5 62,5 50 000 120 92,5 195 105 220 13,5 148 165 77,5 M12 74 73,7 75 000 150 110 230 125 260 13,5 200 200 95 M12 100 90 ABCDEGLMN TX 0,1 BSISO119012:2004OSI -109114002:2)E( ISO 4002 r llAithgs reservde

37、 9 3.6 Type E Rectangular flange mounts See Figure 8 and Table 6. 4M a t e r i a l The material shall be steel E 355C, in accordance with ISO 630, or any material with equivalent mechanical characteristics. General tolerance: ISO 2768-m The two flange halves are to be held together with assembly scr

38、ews. Key 1 plain ring 2 assembly screws Figure 8 Rectangular flange mounts Type E Table 6 Dimensions of rectangular flange mounts Type E Mount for gas spring h10 900 19,5 12 30 32 9 44 25 2 6,6 21,5 2 000 25,5 18 34 38 9 50 30 2 6,6 21,5 AB 1 B 2 B 3 CD 1 D 2 D 3 EJ 0,1 BSISO119012:2004ISO -10911:2)

39、E(4002 10 ISO 4002 All rithgs reresvde 5 Designation A mounting accessory in accordance with this part of ISO 11901 shall be designated by: a) “Mounting base plate” or “Two-part mounting clamp” or “Flange mount” or “Front end support”; b) reference to this part of ISO 11901, i.e. ISO 11901-2; c) typ

40、e of mounting accessory; d) type of the gas spring. EXAMPLE A mounting base plate type A1 for a gas spring of type of 5 000 is designated as follows: Mounting base plate ISO 11901-2 - A1 - 5 000 BSISO119012:2004. 11 BSISO119012:2004BS ISO 11901-2:2004 BSI 389 Chiswick High Road London W4 4AL BSI Bri

41、tish Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of

42、British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of

43、 the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.

44、 Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for inter

45、national standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Te

46、chnical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-. Subscribing members of BSI are kept up to date w

47、ith standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-. Information regarding online access to British Standa

48、rds via British Standards Online can be found at http:/www.bsi- Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval sy