BS ISO 11843-7-2012 Capability of detection Methodology based on stochastic properties of instrumental noise《检测能力 基于仪器噪声随机特性的方法体系》.pdf

《BS ISO 11843-7-2012 Capability of detection Methodology based on stochastic properties of instrumental noise《检测能力 基于仪器噪声随机特性的方法体系》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 11843-7-2012 Capability of detection Methodology based on stochastic properties of instrumental noise《检测能力 基于仪器噪声随机特性的方法体系》.pdf（28页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS ISO 11843-7:2012Capability of detectionPart 7: Methodology based on stochasticproperties of instrumental noiseBS ISO 11843-7:2012 BRITISH STANDARDNational forewordThis British

2、 Standard is the UK implementation of ISO 11843-7:2012.The UK participation in its preparation was entrusted to TechnicalCommittee SS/6, Precision of test methods.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to inc

3、lude all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2012. Published by BSI StandardsLimited 2012ISBN 978 0 580 67951 3ICS 03.120.30; 17.020Compliance with a British Standard cannot confer immunity fromlegal obligations.T

4、his British Standard was published under the authority of theStandards Policy and Strategy Committee on 30 June 2012.Amendments issued since publicationDate Text affectedBS ISO 11843-7:2012 ISO 2012Capability of detection Part 7: Methodology based on stochastic properties of instrumental noiseCapaci

5、t de dtection Partie 7: Mthodologie base sur les proprits stochastiques du bruit instrumentalINTERNATIONAL STANDARDISO11843-7First edition2012-06-01Reference numberISO 11843-7:2012(E)BS ISO 11843-7:2012ISO 11843-7:2012(E)ii ISO 2012 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2012All rights

6、reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the re

7、quester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 11843-7:2012ISO 11843-7:2012(E) ISO 2012 All rights reserved iiiContents PageForeword ivIntroduction v1 Scope 12 Normative refe

8、rences . 13 Terms and definitions . 14 Quantitative analysis and background noise 24.1 Error sources of analysis 24.2 Random processes in background 35 Theories for precision 35.1 Theory based on auto-covariance function . 35.2 Theory based on power spectrum 56 Practical use of FUMI theory 96.1 Esti

9、mation of noise parameters 96.2 Procedures for estimation of SD .10Annex A (informative) Symbols and abbreviated terms used in this part of ISO 11843 13Annex B (informative) Derivation of Formula (7) 14Annex C (informative) Derivation of Formulae (14) to (16) 15Bibliography .17BS ISO 11843-7:2012ISO

10、 11843-7:2012(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subjec

11、t for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC)

12、 on all matters of electrotechnical standardization.International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees

13、are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held

14、responsible for identifying any or all such patent rights.ISO 11843-7 was prepared by Technical Committee ISO/TC 69, Application of statistical methods, Subcommittee SC 6, Measurement methods and results.ISO 11843 consists of the following parts, under the general title Capability of detection: Part

15、 1: Terms and definitions Part 2: Methodology in the linear calibration case Part 3: Methodology for determination of the critical value for the response variable when no calibration data are used Part 4: Methodology for comparing the minimum detectable value with a given value Part 5: Methodology i

16、n the linear and non-linear calibration cases Part 6: Methodology for the determination of the critical value and the minimum detectable value in Poisson distributed measurements by normal approximations Part 7: Methodology based on stochastic properties of instrumental noiseiv ISO 2012 All rights r

17、eservedBS ISO 11843-7:2012ISO 11843-7:2012(E)IntroductionThe series of ISO 11843 is based on the probability distributions of the net state variable (measurand) for both the linear and nonlinear calibration situations. The focus is implicitly, though sometimes explicitly, on the uncertainty associat

18、ed with an estimate of the measured response predominantly coming from the baseline noise in instrumental analysis. In many, if not most, analytical instruments, the baseline noise is considered the prime cause of uncertainty when the sample amount is as low as the minimum detectable value. Within i

19、ts domain of applicability, the method given in this part of ISO 11843 can dispense with the repetition of real samples, thus helping to improve global environments by saving time and energy that would be required by repetition.The basic concept of ISO 11843-7 is the mathematical description of the

20、probability distribution of the response variable in terms of mathematically well-defined random processes. This description straightforwardly leads to the minimum detectable value. As for the relation of the response and measurand, linear and nonlinear calibration functions can be applied. In this

21、manner, compatibility with ISO 11843-2 and ISO 11843-5 is ensured.The definition and applicability of the minimum detectable value are described in ISO 11843-1 and ISO 11843-2; the definition and applicability of the precision profile are described in ISO 11843-5. The precision profile expresses how

22、 the precision changes depending on the net state variable. ISO 11843-7 specifies the practical use of the fundamental concepts in ISO 11843 in case of the background noise predominance in instrumental analysis.The minimum detectable value, xd, is generally expressed in the unit of the net state var

23、iable. If the calibration function is linear, the SD or CV of the response variable estimated in this part of ISO 11843 can linearly be transformed to the SD or CV of the net state variable, which in turn can be used for the estimation of the minimum detectable value, xd.If the calibration function

24、is nonlinear, the precision profile of the response variable in this part of ISO 11843 needs to be transformed to the precision profile of the net state variable as shown in ISO 11843-5. In this situation, the contents of ISO 11843-5 can be used for this purpose without the slightest modification. I

25、SO 2012 All rights reserved vBS ISO 11843-7:2012BS ISO 11843-7:2012Capability of detection Part 7: Methodology based on stochastic properties of instrumental noise1 ScopeBackground noise exists ubiquitously in analytical instruments, whether or not a sample is applied to the instrument. This part of

26、 ISO 11843 is concerned with mathematical methodologies for estimating the minimum detectable value in case that the most predominant source of measurement uncertainty is background noise. The minimum detectable value can directly and mathematically be derived from the stochastic characteristics of

27、the background noise.It specifies basic methods to extract the stochastic properties of the background noise, use the stochastic properties to estimate the standard deviation (SD) or coefficient of variation (CV) of the response variable, and calculate the minimum detectable value based on the SD or

28、 CV obtained above.The methods described in this part of ISO 11843 are useful for checking the detection of a certain substance by various types of measurement equipment in which the background noise of the instrumental output predominates over the other sources of measurement uncertainty. Feasible

29、choices are visible and ultraviolet absorption spectrometry, atomic absorption spectrometry, atomic fluorescence spectrometry, luminescence spectrometry, liquid chromatography and gas chromatography.2 Normative referencesThe following referenced documents are indispensable for the application of thi

30、s document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 11843-1:1997, Capability of detection Part 1: Terms and definitionsISO 11843-2:2000, Capability of detection Part 2: Methodol

31、ogy in the linear calibration caseISO 11843-5:2008, Capability of detection Part 5: Methodology in the linear and non-linear calibration casesISO 3534-1, Statistics Vocabulary and symbols Part 1: General statistical terms and terms used in probabilityISO 3534-2, Statistics Vocabulary and symbols Par

32、t 2: Applied statisticsISO 3534-3, Statistics Vocabulary and symbols Part 3: Design of experimentsISO 5725-1, Accuracy (trueness and precision) of measurement methods and results Part 1: General principles and definitions3 Terms and definitionsFor the purposes of this document, the terms and definit

33、ions given in ISO 3534-1, ISO 3534-2, ISO 3534-3, ISO 5725-1, ISO 11843-1, ISO 11843-2, ISO 11843-5 and the following apply. A list of symbols and abbreviated terms used in this document is provided in Annex A.INTERNATIONAL STANDARD ISO 11843-7:2012(E) ISO 2012 All rights reserved 1BS ISO 11843-7:20

34、12ISO 11843-7:2012(E)3.1 precision profilemathematical description of the standard deviation (SD) of the response variable Y(X) or net state variable X(X) as a function of the net state variable.ISO 11843-5:2008, 3.4NOTE 1 The coefficient of variation (CV) of the response variable or net state varia

35、ble as a function of the net state variable is also referred to as a precision profile.NOTE 2 Precision means the SD or CV of the observed response variable or SD or CV of the net state variable when estimated by the calibration function (ISO 11843-5).3.2 minimum detectable value of the net state va

36、riablexdvalue of the net state variable in the actual state that will lead, with probability 1 , to the conclusion that the system is not in the basic stateNOTE 1 Under the assumption that the SD, X(X), of the net state variable is constant (X(X) = X, the minimum detectable value, xd, is defined asx

37、d= (kc+ kd)X(1)where kcdenotes a coefficient to specify the probability of an error of the first kind;kdis a coefficient to specify the probability of an error of the second kind.If the SD, Y, of the response variable is assumed to be constant Y(X) = Y, then the minimum detectable value can be calcu

38、lated by the following equation:xd= (kc+ kd)(Y/|dY/dX|) (2)where |dY/dX| denotes the absolute value of the slope of the linear calibration function and is constant.NOTE 2 If the net state variable is normally distributed, the coefficients kc= kd= 1,65 specify the probabilities of an error of the fir

39、st and second kinds (= 5 %) and Formula (1) can simply be written as xd= 3,30X.NOTE 3 If kc= kd= 1,65, Formula (1) takes the form that X/ xd= 1/3,30 = 30 %. Therefore, xdcan be found in the precision profile. xdis located at X, the CV of which is 30 %.NOTE 4 Different types of precision profiles are

40、 defined, but they can be transformed to each other. For example, the SD, Y(X), of the response variable can be transformed to the SD, X(X), of the net state variable by means of the absolute value of the derivative, |dY/dX|, of the calibration function Y = f(X): X(X) = Y(X)/|dY/dX| (ISO 11843-5). T

41、his treatment is an approximation, the extent of which depends on local curvature, involving d2Y/dX2.NOTE 5 Adapted from ISO 11843-5:2008.4 Quantitative analysis and background noise4.1 Error sources of analysisThe quantitative analysis to obtain a measurand from a sample is generally considered to

42、consist of preparation, instrumental analysis, data handling and calibration. These steps of analysis are mechanically independent of each other and so are probabilistically independent as well.This part of ISO 11843 applies only to instrumental analysis. However, the errors from the other steps aff

43、ect the error of the final value of the measurand, as well. That is, the combined uncertainty associated with an estimate 2 ISO 2012 All rights reservedBS ISO 11843-7:2012ISO 11843-7:2012(E)of the measurand depends on the propagation of all uncertainties relating to the relevant steps. The following

44、 conditions are necessary for the use of ISO 11843-7.At concentrations near the minimum detectable value in chromatography, the error from the sample injection into a chromatograph is even less important (e.g. CV = 0,3 % in a recent apparatus) than the background noise (CV = 30 % by definition). If

45、the importance of a factor other than noise is comparable to that of the noise, the methodologies of this part of ISO 11843 are not applicable.Data handling is usually a process to extract a signal component from noisy instrumental output such as peak height or area, which is a relative height of a

46、summit of a peak-shaped signal or integration of intensities over a signal region, respectively. The statistical influences of this process are the major concern of this part of ISO 11843. The use of a digital or analogue filter can also be taken into account, if the noise after the filtration is an

47、alysed for this purpose.4.2 Random processes in backgroundTypical examples of the response variable are area and height measured in chromatography. In this part of ISO 11843, intensity difference Formula (6) and area Formulae (10) and (11) are taken as the difference and summation of intensities Yio

48、f instrumental output. The response variables are usually independent of each other even if they are obtained from consecutive measurement by the same instrument. On the other hand, the consecutive intensities Yiare formulated as a time-dependent random process, and in many cases, can be considered

49、1/f noise.1The power spectrum, P(f), of 1/f noise has a slope inversely proportional to frequency, f:Pff()1(3)when f is near zero.In mathematical theory, the simplest model of random processes is the white noise. Let widenote the random variable of the white noise at point i. By definition, the mean of the white noise is zero and the SD, w , of the white noise is constant at every point i. A prominent feature of the white noise is that the noise intensities, wiand wj, are independent of e