BS ISO 11515-2013 Gas cylinders Refillable composite reinforced tubes of water capacity between 450 L and 3000 L Design construction and testing《气瓶 含水量在450 L到3000 L之间的可再填充的加强型管道 设计.pdf

《BS ISO 11515-2013 Gas cylinders Refillable composite reinforced tubes of water capacity between 450 L and 3000 L Design construction and testing《气瓶 含水量在450 L到3000 L之间的可再填充的加强型管道 设计.pdf》由会员分享，可在线阅读，更多相关《BS ISO 11515-2013 Gas cylinders Refillable composite reinforced tubes of water capacity between 450 L and 3000 L Design construction and testing《气瓶 含水量在450 L到3000 L之间的可再填充的加强型管道 设计.pdf（52页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS ISO 11515:2013Gas cylinders Refillablecomposite reinforced tubesof water capacity between450 L and 3000 L Design,construction and testingBS ISO 11515:2013 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 11515:2013.The UK participatio

2、n in its preparation was entrusted to TechnicalCommittee PVE/3/3, Gas containers - Transportable gas containers- Cylinder design, construction and testing at the time ofmanufacture.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does

3、not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2013. Published by BSI StandardsLimited 2013ISBN 978 0 580 66099 3ICS 23.020.30Compliance with a British Standard cannot confer immunity fromlegal obl

4、igations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 August 2013.Amendments issued since publicationDate Text affectedBS ISO 11515:2013 ISO 2013Gas cylinders Refillable composite reinforced tubes of water capacity between 450 L and 3000

5、 L Design, construction and testingBouteilles gaz Bouteilles tubulaires en composite renforc rechargeables dune capacit de 450 L 3000 L Conception, construction et essaisINTERNATIONAL STANDARDISO11515First edition2013-07-15Reference numberISO 11515:2013(E)BS ISO 11515:2013ISO 11515:2013(E)ii ISO 201

6、3 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2013All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, wit

7、hout prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in Switz

8、erlandBS ISO 11515:2013ISO 11515:2013(E) ISO 2013 All rights reserved iiiContents PageForeword ivIntroduction v1 Scope . 12 Normative references 13 Terms and definitions .24 Symbols 55 Inspection and testing 56 Materials .56.1 Liner materials 56.2 Composite overwrap 67 Design and manufacture 67.1 Ge

9、neral . 67.2 Design submission . 77.3 Manufacturing . 88 Type approval procedure 98.1 General . 98.2 Prototype tests 98.3 New design 108.4 Design variants 118.5 Type approval test procedures and criteria 128.6 Failure of type approval tests 299 Inspection and testing at time of manufacture 299.1 Lin

10、ers for Type 2 and Type 3 tubes 299.2 Liners for Type 4 tubes . 299.3 Failure of liner batch tests 309.4 Overwrap materials . 309.5 Composite tube 319.6 Failure of batch tests . 3110 Tube marking 3210.1 General 3210.2 Additional marking 32Annex A (informative) Examples of design approval certificate

11、 33Annex B (informative) Specimen test reports 34Annex C (normative) Ultrasonic inspection for seamless steel liners and metal tubing 36Bibliography .41BS ISO 11515:2013ISO 11515:2013(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards b

12、odies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizati

13、ons, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its furthe

14、r maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2. www.iso.org/directivesAtte

15、ntion is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introductio

16、n and/or on the ISO list of patent declarations received. www.iso.org/patentsAny trade name used in this document is information given for the convenience of users and does not constitute an endorsement.The committee responsible for this document is ISO/TC 58, Gas cylinders, Subcommittee SC 3, Cylin

17、der design.iv ISO 2013 All rights reservedBS ISO 11515:2013ISO 11515:2013(E)IntroductionThe purpose of ISO 11515 is to provide a specification for the design, manufacture, inspection and testing of composite tubes for worldwide usage. The objective is to balance design and economic efficiency agains

18、t international acceptance and universal utility.ISO 11515 aims to eliminate the concern about climate, duplicate inspection and restrictions currently existing because of lack of definitive International Standards and should not be construed as reflecting on the suitability of the practice of any n

19、ation or region.ISO 11515 addresses the general requirements on design, construction and initial inspection and testing of pressure receptacles of the United Nations Recommendations on the Transport of Dangerous Goods Model Regulations.Annexes A and B of ISO 11515 are for information only. ISO 2013

20、All rights reserved vBS ISO 11515:2013BS ISO 11515:2013Gas cylinders Refillable composite reinforced tubes of water capacity between 450 L and 3000 L Design, construction and testing1 ScopeThis International Standard specifies minimum requirements for the design, construction and performance testing

21、 of composite reinforced tubes between 450 l and 3 000 l water capacity, for transport, storage and use of compressed or liquefied gases with test pressures up to and including 1600 bar with a design life of at least 15 years and less than or equal to 30 years. The expected service temperatures are

22、between 40 C and +65 C.The tubes defined are one of three types:Type 2: a hoop wrapped tube with a load sharing metal liner and composite reinforcement on the cylindrical portion only.Type 3: a fully wrapped tube with a load sharing metal liner and composite reinforcement on both the cylindrical por

23、tion and the dome ends.Type 4: a fully wrapped tube with a non-load sharing liner and composite reinforcement on both the cylindrical portion and the dome ends.The Type 4 tubes manufactured and tested to this International Standard are not intended to contain toxic, oxidizing or corrosive gases.This

24、 International Standard is limited to tubes with composite reinforcement of carbon fibre or aramid fibre or glass fibre (or a mixture thereof) in a matrix.Composite tubes can be used alone or in batteries to equip trailers or skids (ISO modules) or multiple element gas containers (MEGC) for the tran

25、sportation and distribution of gases. This International Standard does not include consideration of any additional stresses that can occur during service or transport, (e.g. torsional / bending stresses). However it is important that the stresses associated with mounting the tube are considered by t

26、he assembly manufacturer and the tube manufacturer.NOTE The design life of tubes according to this International Standard for transport of dangerous goods can be limited by the applicable regulations.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in th

27、is document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 306, Plastics Thermoplastic materials Determination of Vicat softening temperature

28、 (VST)ISO 527-1, Plastics Determination of tensile properties Part 1: General principlesISO 527-2, Plastics Determination of tensile properties Part 2: Test conditions for moulding and extrusion plasticsISO 3341, Textile glass Yarns Determination of breaking force and breaking elongationISO 4624, Pa

29、ints and varnishes Pull-off test for adhesionISO 6506-1, Metallic materials Brinell hardness test Part 1: Test methodINTERNATIONAL STANDARD ISO 11515:2013(E) ISO 2013 All rights reserved 1BS ISO 11515:2013ISO 11515:2013(E)ISO 6508-1, Metallic materials Rockwell hardness test Part 1: Test methodISO 6

30、892-1, Metallic materials Tensile testing Part 1: Method of test at room temperatureISO 7225, Gas cylinders Precautionary labelsISO 7866, Gas cylinders Refillable seamless aluminium alloy gas cylinders Design, construction and testingISO 9227:2012, Corrosion tests in artificial atmospheres Salt spra

31、y testsISO 9712, Non-destructive testing Qualification and certification of NDT personnelISO 9809-1, Gas cylinders Refillable seamless steel gas cylinders Design, construction and testing Part 1: Quenched and tempered steel cylinders with tensile strength less than 1 100 MPaISO 9809-2, Gas cylinders

32、 Refillable seamless steel gas cylinders Design, construction and testing Part 2: Quenched and tempered steel cylinders with tensile strength greater than or equal to 1 100 MPaISO 9809-3, Gas cylinders Refillable seamless steel gas cylinders Design, construction and testing Part 3: Normalized steel

33、cylindersISO 10618, Carbon fibre Determination of tensile properties of resin-impregnated yarnISO 11114-1, Gas cylinders Compatibility of cylinder and valve materials with gas contents Part 1: Metallic materialsISO 11114-2, Gas cylinders Compatibility of cylinder and valve materials with gas content

34、s Part 2: Non-metallic materialsISO 11120, Gas cylinders Refillable seamless steel tubes of water capacity between 150 l and 3000 l Design construction and testingISO 13341, Gas cylinders Fitting of valves to gas cylindersISO 13769, Gas cylinders Stamp markingASTM D 522-93a, Standard Test Methods fo

35、r Mandrel Bend Test of Attached Organic CoatingsASTM D1308, Standard Test Method for Effect of Household Chemicals on Clear and Pigmented Organic FinishesASTM D2794, Standard Test Method for Resistance of Organic Coatings to the Effects of Rapid Deformation (Impact)ASTM D3170, Standard Test Method f

36、or Chipping Resistance of CoatingsASTM D7269, Standard Test Methods for Tensile Testing of Aramid Yarns3 Terms and definitionsFor the purposes of this document, the following terms and definitions apply.3.1aramid fibrecontinuous filaments of aramid laid up in tow form, used for reinforcement3.2autof

37、rettagepressure application procedure which strains the metal liner past its yield point sufficient to cause permanent plastic deformation, and results in the liner having compressive stresses and the fibres having tensile stresses when at zero internal gauge pressure2 ISO 2013 All rights reservedBS

38、 ISO 11515:2013ISO 11515:2013(E)3.3batchcollective term for a set of homogeneous items or materialNote 1 to entry: The number of items in a batch can vary according to the context in which the term is used.3.4batch of load sharing linersquantity of up to 30 liners of the same nominal diameter, lengt

39、h, thickness and design, made successively from the same material cast (heat) and processed in the same heat treatment equipment (i.e. a continuous furnace process or a single furnace charge) using the same heat treatment parameters3.5batch of non-metallic linersquantity of non-metallic liners of th

40、e same nominal diameter, length, thickness and design, made successively and subjected to the same continuous manufacturing process3.6batch of non-load sharing metal liners or metal bossesquantity of non-load sharing metal liners or metal bosses of the same nominal diameter, length, thickness and de

41、sign, made successively from the same material cast (heat) and processed in the same heat treatment equipment using the same heat treatment parameters3.7batch of finished tubesproduction quantity of up to 200 finished tubes successively produced (plus finished tubes required for destructive testing)

42、, of the same nominal diameter, length, thickness and designNote 1 to entry: The batch of finished tubes can contain different batches of liners, fibres and matrix materials.3.8burst pressurehighest pressure reached in a tube or liner during a burst test3.9carbon fibrecontinuous filaments of carbon

43、laid up in tow form, used for reinforcement3.10composite overwrapcombination of fibres and matrix used to reinforce the tube, including any barrier or protective layers that are a permanent part of the design3.11dedicated gas serviceservice in which a tube is to be used only with specified gas or ga

44、ses3.12equivalent fibrefibre equivalent to a fibre used in a previously prototype tested tube3.13exterior coatinglayers of material applied to the tube as protection or for cosmetic purposesNote 1 to entry: The coating can be transparent or opaque. ISO 2013 All rights reserved 3BS ISO 11515:2013ISO

45、11515:2013(E)3.14equivalent linerliner manufactured from the same nominal raw materials, using the same process of manufacture and having the same physical structure and the same nominal physical properties (within 5 %) of the approved liner design3.15glass fibrecontinuous filaments of glass laid up

46、 in tow form, used for reinforcement3.16leakescape of gas at a rate greater than 510-3mbar.l/s through a defect rather than permeation3.17linerinner portion of the composite tube, whose purpose is both to contain the gas and transmit the gas pressure to the fibres3.18load sharing linerliner that has

47、 a burst pressure greater than or equal to 5 % of the nominal burst pressure of the finished composite tube3.19non-load-sharing linerliner which has a burst pressure less than 5 % of the nominal burst pressure of the finished composite tube3.20matrixmaterial that is used to bind and hold the fibres

48、in place3.21minimum design burst pressureminimum burst pressure specified by the manufacturer and that shall be achieved during a burst test3.22tubetransportable pressure receptacle of a water capacity exceeding 150 litres3.23representative composite tubea shorter tube with the same nominal diameter

49、, and manufactured using the same materials and manufacturing technique, and using a representative wrapping pattern (same number of strands and same number of layers) so as to represent an equivalent stress compared to a full scale prototype3.24tubinghollow cylindrical body of metal or other material, used for conveying or containing liquids or gases3.25Type 2 tubehoop wrapped tube with a load sharing metal liner and composite reinforcement on the cylindrical