BS ISO 11485-1-2012 Glass in building Curved glass Terminology and definitions《建筑用玻璃 曲面玻璃 术语和定义》.pdf

《BS ISO 11485-1-2012 Glass in building Curved glass Terminology and definitions《建筑用玻璃 曲面玻璃 术语和定义》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 11485-1-2012 Glass in building Curved glass Terminology and definitions《建筑用玻璃 曲面玻璃 术语和定义》.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationGlass in building Curved glassPart 1: Terminology and definitionsBS ISO 11485-1:2011National forewordThis British Standard is the UK implementation of ISO 11485-1:2011.The UK par

2、ticipation in its preparation was entrusted by Technical CommitteeB/520, Glass and glazing in building, to Subcommittee B/520/1, Basic and transformed glass products.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to

3、 include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2012.Published by BSI Standards Limited 2012. ISBN 978 0 580 60431 7 ICS 01.040.81; 81.040.20Compliance with a British Standard cannot confer immunity from legal

4、obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 December 2012.Amendments issued since publicationAmd. No. Date Text affectedBRITISH STANDARDBS ISO 11485-1:2011Glass in building Curved glass Part 1: Terminology and definitionsVe

5、rre dans la construction Verre bomb Partie 1: Terminologie et dfinitions ISO 2011Reference numberISO 11485-1:2011(E)First edition2011-12-15ISO 11485-1INTERNATIONALSTANDARDBS ISO 11485-1:2011ISO 11485-1:2011(E)COPYRIGHT PROTECTED DOCUMENT ISO 2011All rights reserved. Unless otherwise specified, no pa

6、rt of this publication may be reproduced or utilized in any form or by any means,electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOsmember body in the country of the requester.ISO copyright officeCase postale 56 C

7、H-1211 Geneva 20Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.orgPublished in Switzerlandii ISO 2011 All rights reservedBS ISO 11485-1:2011ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies(ISO me

8、mber bodies). The work of preparing International Standards is normally carried out through ISOtechnical committees. Each member body interested in a subject for which a technical committee has beenestablished has the right to be represented on that committee. International organizations, government

9、al andnon-governmental, in liaison with ISO, also take part in the work. ISO collaboratesclosely with the InternationalElectrotechnical Commission (IEC) on all matters of electrotechnical standardization.International Standards are drafted in accordance with the rules given in the ISO/IEC Directives

10、, Part 2.The main task of technical committees is to prepare International Standards. Draft International Standardsadopted by the technical committees are circulated to the member bodies for voting. Publication as anInternational Standard requires approval by at least 75 % of the member bodies casti

11、ng a vote.Attention is drawn to the possibility that some of the elements of this document may be the subject of patentrights. ISO shall not be held responsible for identifying any or all such patent rights.ISO 11485-1 was prepared by Technical Committee ISO/TC 160, Glass in building, Subcommittee S

12、C 1,Product considerations.ISO 11485 consists of the following parts, under the general title Glass in building Curved glass : Part 1: Terminology and definitions Part 2: Quality requirements Part 3: Requirements for tempered and laminated curved safety glass1)1) Under preparation.ISO 11485-1:2011(E

13、) ISO 2011 All rights reserved iiiBS ISO 11485-1:2011INTERNATIONAL STANDARD ISO 11485-1:2011(E)Glass in building Curved glass Part 1:Terminology and definitions1 ScopeThis part of ISO 11458 specifies terminology and definitions for curved glass used in general buildingconstruction, furniture, displa

14、y and various other non-automotive applications.2 Terms and definitionsFor the purposes of this document, the following terms and definitions apply.2.1 curved glass bent glass (US) sheet of annealed glass curved by a heating process2.2 curved annealed glass glass that is curved and then cooled slowl

15、y so that it recovers its initial mechanical characteristics2.3 curved patterned glass flat patterned glass that has been formed into a curved shape2.4 curved wired glass flat wired glass that is formed into a curved shape2.5 curved insulating glass two panes of curved glass that have been fabricate

16、d into an insulating glass unit2.6 curved tempered glass flat glass that is formed into a curved shape by heating above a specified temperature and then subjected to arapid and controlled cooling process in order to give it greatly increased resistance to thermal and mechanicalstressNOTE In this Int

17、ernational Standard, the term “tempered” also means “thermally toughened”.2.7 curved heat-soaked tempered glass tempered curved glass that has been post-processed using a specified heat-soak cycle with the intent ofisolating possible nickel sulfide inclusions2.8 curved tempered enamelled glass curve

18、d tempered glass which has a ceramic frit fired into the surface during the tempering processNOTE 1 After tempering, the ceramic frit becomes an integral part of the glass. ISO 2011 All rights reserved 1BS ISO 11485-1:2011NOTE 2 The application of the ceramic frit may be by a continuous or discontin

19、uous application, e.g, screen printing.2.9curved heat-strengthened glassflat glass that has been formed into a shape and heat-strengthenedNOTE The specifications of curved heat-strengthened glass are under consideration.2.10curved chemically strengthened glassflat glass that has been formed into a s

20、hape and chemically strengthened2.11curved laminated glassassembly consisting of curved glass sheets joined together with cast-in-place resins or films2.12curved laminated tempered glassassembly consisting of curved tempered sheets joined together with cast-in-place resins or films2.13curved safety

21、glasscurved glass that in the case of accidental breakage, reduces the risk of cutting or piercing injuries and/or offers residual resistance by retaining the glass fragmentsNOTE 1 The curved glass can be tempered or laminated for example.NOTE 2 Curved safety glass is classified according to ISO 114

22、85-2.2.14concave“hollow” face of curved glass2.15convex“bulge” face of curved glass2.16angleangular measurement of a segment of a curve in degreesNOTE See Figure 1.2.17inner radiusRiradius of concave faceNOTE See Figures 1 and 2.2.18outer radiusReradius of convex faceNOTE See Figures 1 and 2.ISO 114

23、85-1:2011(E)2 ISO 2011 All rights reservedBS ISO 11485-1:20122.19 arc Alength of the curved portionNOTE 1 See Figure 1.NOTE 2 An arc is described as either interior arc (Ai) or exterior arc (Ae).2.20 chord of the arc Caline segment that connects end points of an arcNOTE 1 See Figure 1.NOTE 2 A chord

24、 is described as either an interior chord (Cai) or an exterior chord (Cae). The interior chord (Cai)corresponds to the interior arc (Ai) and the exterior chord (Cae) corresponds to the exterior arc (Ae).2.21 rise depth Fsegment between the middle of the arc of the circle and the middle of the chord

25、that subtends the arcNOTE See Figure 1.2.22 girth Gdistance around the concave or convex surface measured perpendicular to the height including any flatsNOTE See Figure 1.2.23 chord of the girth Cgline segment that connects end points of a girthNOTE See Figure 1.2.24 depth Prmaximal distance between

26、 the upper part of the girth (G) and the corresponding chord (Cd)NOTE See Figure 1.2.25 flat Bflat segments forming a part of curved glassNOTE See Figure 1.2.26 length Ldimension of the straight edge of the curved glassNOTE See Figure 1.ISO 11485-1:2011(E) ISO 2011 All rights reserved 3BS ISO 11485-

27、1:20112.27 thickness Tnominal thickness of the final productNOTE 1 In a curved insulating glass, the thickness is the sum of the thicknesses of the inner glass (Ti), the gas space(Ta) and the outer glass (Te).NOTE 2 See Figures 1 and 2.2.28 plan document containing the geometry of the product to be

28、made2.29 drawing graphic details defining the geometry of the product to be made2.30 lay out representation of scale 1:1 of the curvature profile2.31 template three-dimensional reproduction at scale 1:1 to determine the dimensions and shape of the product to be made2.32 cutting template form (patter

29、n) that facilitates accuracy in the glass forming process by providing the proper curved glassinformation for size, shape and contour2.33 model product in glass or other material at scale 1:1 that is an identical reproduction2.34 curvature profile geometrical shape of the curved part of the curved g

30、lass2.35 shape accuracy PCaccuracy of the contoured form including curvature, arc(s), and even flats2.36 cross-curve deviation sag deviation from a straight line or reference curve perpendicular to the curvature measured on the concave side2.37 edge straightness deviation warp RBdeviation from strai

31、ghtness of the straight edges of the glass2.38 twist deviation Vone or more of the corners of the glass are not in the same planeISO 11485-1:2011(E)4 ISO 2011 All rights reservedBS ISO 11485-1:20112.39 optical distortion slight deformation of the images seen in reflection or in transmission, inheren

32、t to the process of bending glass2.40 displacement dmisalignment at any one edge of the constituent glass panes making up the curved laminated and/or insulatingglassNOTE 1 d1: displacement of one of the edges of the glass during the manufacture of laminated curved glass.NOTE 2 d2: displacement of th

33、e edges of the glass during the manufacture of insulating glass.2.41 cold crack crack caused by a difference of temperature of the surface in the cooling processNOTE 1 For example, around tong marks or ring marks.NOTE 2 Cold cracks appear in a whisker-like or hair-like shape in the case of curved te

34、mpered glass and in a shellshape appearing around crossing points of wires in the case of annealed curved wired glass.2.42 pock marks process surface blemishes that consist of small, shallow areas, circular in shape, on the surface of the glass2.43 ring marks process surface blemishes that consist o

35、f shallow marks typically running along the perimeter of the glasssurface2.44 tong marks slight indentations along the top edge of vertically curved glass, resulting from the method of holding orsupporting the glass with tongs in vertical form2.45 tools elements particular to an order which allow th

36、e fabrication of curved glass2.46 gauge measurement tool for manufacturing and checking the curvature profile of the finished productISO 11485-1:2011(E) ISO 2011 All rights reserved 5BS ISO 11485-1:201112LRiAReCaiFTa)RiLFAGBCaPrCgb)Key1 bulge outer face (convex)2 hollow inner face (concave)Figure 1

37、Examples of terms and dimensionsISO 11485-1:2011(E)6 ISO 2011 All rights reservedBS ISO 11485-1:201112tetatiRiReTKey1 convex part2 concave partFigure 2 Thicknesses and radius of an insulating glassISO 11485-1:2011(E) ISO 2011 All rights reserved 7BS ISO 11485-1:2011Bibliography1 ISO 11485-2, Glass i

38、n building Curved glass Part 2: Quality requirements2 ISO 12543 (all parts), Glass in building Laminated glass and laminated safety glass3 ASTM C1464-06, Standard Specification for Bent GlassISO 11485-1:2011(E)8 ISO 2011 All rights reservedBS ISO 11485-1:2011This page deliberately left blankThis pag

39、e deliberately left blankBSI is the independent national body responsible for preparing British Standards and other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. BSI is incorporated by Royal Charter. British S

40、tandards and other standardisation products are published by BSI Standards Limited.British Standards Institution (BSI)raising standards worldwideBSI389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards and PASs are periodically updated by amendment or revision.

41、Users of British Standards and PASs should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using British Standards would inform the

42、 Secretary of the technical committee responsible, the identity of which can be found on the inside frontcover. Similary for PASs, please notify BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers BSI Subscribing Members an individual updating service called PLUS which

43、ensures that subscribers automatically receive the latest editions of British Standards and PASs.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orde

44、rs for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, BSI will supply the British Standard implementation of the relevant international standard,

45、 unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: BSI Subscribing Members are kept up to date with standards developments a

46、nd receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards and PASs via British Standards Online can

47、be found at information about British Standards is available on the BSI website at www.bsi- the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that own copyright in the information use

48、d (such as the international standardisation bodies) has formally licensed such information to BSI for commerical publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to