BS ISO 11377-1998 Textile floor coverings - Floor soiling - Test site set-up and soiling evaluation《铺地织物 地板肮脏度 试验位置确定和肮脏度的评估》.pdf

《BS ISO 11377-1998 Textile floor coverings - Floor soiling - Test site set-up and soiling evaluation《铺地织物 地板肮脏度 试验位置确定和肮脏度的评估》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 11377-1998 Textile floor coverings - Floor soiling - Test site set-up and soiling evaluation《铺地织物 地板肮脏度 试验位置确定和肮脏度的评估》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS ISO 11377:1997 Textile floor coverings Floorsoiling Test site set-up and soiling evaluation ICS 59.080.60BSISO11377:1997 This British Standard, having been prepared under the directionof the Sector Board forMaterials and Chemicals, waspublished under the authorityof the Standards

2、 Boardand comes into effect on 15 April 1998 BSI 04-1999 ISBN 0 580 29692 X National foreword This British Standard reproduces verbatim ISO 11377:1997 and implements it as the UK national standard. The UK participation in its preparation was entrusted to Technical Committee PRI/3, Textile floor cove

3、rings, which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and prom

4、ulgate them in the UK. A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the s

5、ection entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct applicati

6、on. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, theISO title page, page ii, pages 1 to 4, an inside back cover and a back cover. This standard has been upd

7、ated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No. Date CommentsBSISO11377:1997 BSI 04-1999 i Contents Page National foreword Inside front cover Foreword ii 1 Scope

8、1 2 Normative references 1 3 Principle 1 4 Test site 1 5 Test specimen preparation 1 6 Textile floor covering installation 1 7 Test procedure 1 8 Evaluation 3 9 Test report 4 Annex A (informative) Bibliography Inside back cover Figure 1 Test site layout 2 Figure 2 Examples of test specimen layouts 3

9、ii blankBSISO11377:1997 ii BSI04-1999 Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body

10、 interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotec

11、hnical Commission (IEC) on all matters of electrotechnical standardization. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75% of the member bodies casting a vote

12、. International Standard ISO 11377 was prepared by Technical Committee ISO/TC 38, Textiles, Subcommittee SC 12, Textile floor coverings. Annex A of this International Standard is for information only. Descriptors: Textiles, floor coverings, textile floor coverings, tests, cleanliness checks, determi

13、nation, soiling, testing conditions.BSISO11377:1997 BSI 04-1999 1 1 Scope This International Standard specifies the procedure for setting up a test site for textile floor coverings and the procedure for evaluation of levels of soiling as measured by colour change. 2 Normative references The followin

14、g standards contain provisions which, through reference in this text constitute provisions of this International Standard. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this International Standard are encourag

15、ed to investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO maintain registers of currently valid International Standards ISO 105-A02:1993, Textiles Tests for colour fastness Part A02: Grey scale for assessing change in colour. ISO

16、105-J01: 1) , Textiles Tests for colour fastness Part J01: General principles for the measurement of surface colour. ISO 1957:1986, Machine-made textile floor coverings Sampling and cutting specimens for physical tests. 3 Principle Samples of textile floor covering are exposed to foot traffic at a c

17、ontrolled test site and are evaluated for change in colour after a given level of soiling is reached. The textile floor coverings can be evaluated for soiling in-situ for intermediate assessments and, after removal from the test site, for final assessment. 4 Test site The test site shall be remote f

18、rom outside entrances and isolated from nontypical, greasy, oily or wet traffic. It shall consist of a level corridor of width not more than 1,5 m and not less than 1,3 m, with straight, non-turning traffic in both directions, as shown in Figure 1. The test site may be equipped with a photoelectric

19、traffic counter positioned 1,25 m above floor level. The test site shall not be in areas where people gather, such as those containing bulletin boards or vending machines. The floor shall be level and free from irregularities. At least 2,5 m of buffer textile floor covering, free from contaminants a

20、nd exhibiting minimum fibre shedding, shall be placed at each end of the test textile floor covering. 5 Test specimen preparation Textile floor coverings under test shall be sampled in accordance with ISO 1957 and square test specimens shall be prepared having sides measuring (35010)mm. They shall b

21、e placed in two lines along the length of the corridor (see Figure 1). Buffer textile floor covering between300 mm and 400 mm in width shall be attached to the sides of the test area, so as to fill the width of the corridor. For each sample of floor covering there shall be at least two replicate spe

22、cimens. 6 Textile floor covering installation Textile floor coverings shall be installed in such a way that they ensure safe traffic. This is easily achieved with double faced pressure-sensitive adhesive tape. Alternatively, individual specimens may be mounted to a removable rigid or semi-rigid subs

23、trate of size identical to the test specimens and inserted into the test area. Where traffic crosses from hard flooring to textile floor covering and vice versa, the textile floor covering edge shall be secured with rubber, plastic or metal edging, or tape to prevent a tripping hazard. Care shall be

24、 taken to minimize textile floor covering junctions where there are large differences in carpet thickness and other potential tripping hazards. NOTEIf it is deemed beneficial to identify the site as one where a trial is in progress, it is recommended that any safety signs which are used conform to I

25、SO 3864. When first installed, the test specimens shall be placed in alternating positions. For example, if there are two sets of replicate specimens, A and B, they shall be placed AB/BA across the width of the test site; if there are three sets of replicate specimens, A, B and C, they shall be plac

26、ed AB/CA/BC; and if there are four sets of replicate specimens, A, B, C and D they shall be placed AB/CD/BA/DC (see Figure 2). 7 Test procedure 7.1 To ensure even soiling, systematic transfer of test specimens between lines shall take place every two days, or after a predetermined number of traffick

27、s, with specimens being rotated 90 in a clockwise direction, moved two places down the length of the corridor and moved to the other line. Replicate specimens shall be placed away from each other where possible within the test area (see Figure 2) to help to assess whether even soiling has taken plac

28、e. 1) To be published. (Revision of ISO 105-J01:1989)BSISO11377:1997 2 BSI 04-1999 Figure 1 Test site layoutBSISO11377:1997 BSI 04-1999 3 7.2 When the positions of the test specimens have been rotated they shall be cleaned with a vacuum cleaner, using two double strokes i.e. twice backwards and twic

29、e forwards, in order to give all parts of all specimens equal treatment, as follows. The first two double strokes shall be made with the vacuum cleaner suction slot approximately 50% on the buffer carpet and 50% over the test area. Each subsequent series of strokes is made parallel to the first seri

30、es with50% overlap, ending when the buffer strip at the other side is included in the overlap. 7.3 Test specimens shall be trafficked until soiling has reached a predetermined level for one of the sets of specimens which has been selected as a reference, after a predetermined number of trafficks or

31、after a fixed period of time. The predetermined soiling level is assessed to a grey scale level (e.g.level3) or the colour difference measured instrumentally. Alternatively, a standard or control specimen may be included in every test and compared with presoiled samples of the standard or control sp

32、ecimen which are held in the laboratory. 8 Evaluation Prior to evaluation the specimens shall be suction cleaned in accordance with the procedure described in 7.2. The soiling level of each test specimen shall be assessed using at least one of the following techniques a) colour measurement device de

33、scribed in ISO105-J01; b) grey scales and procedure described in ISO105-A02; c) visual comparative ranking. Figure 2 Examples of test specimen layoutsBSISO11377:1997 4 BSI 04-1999 When using colour measurements, colour change shall be expressed as the difference between the soiled specimen and the u

34、ntrafficked control. NOTECaution should be employed when measuring colour difference, since pile flattening and the method of introducing the test specimen to the instrument can profoundly influence results. 9 Test report The test report shall include the following information: a) all the informatio

35、n necessary for complete identification of the textile floor coverings being tested; b) a reference to this International Standard; c) the purpose of the test; d) a description of the test site with lay-out of test specimens at the start and at the completion of the test; e) the rotation and transfe

36、r procedure 7.1; f) a description of the maintenance procedure (including type of vacuum cleaner used); g) the predetermined level to which one of the sets of test specimens was soiled, the number of trafficks or the length of time test specimens were on the floor; h) the method(s) of evaluation; i)

37、 the test results; j) additional information which may have affected the results, e.g. relative humidity and temperature measurements of the test site during the test period; k) a statement that the results obtained are valid only within the test site; l) the date of the test.BSISO11377:1997 BSI 04-

38、1999 Annex A (informative) Bibliography 1 ISO 3864:1984, Safety colours and safety signs.BSISO 11377:1997 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in E

39、urope and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our prod

40、ucts and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members

41、an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In respo

42、nse to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through

43、its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards

44、 developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publi

45、cations of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written perm

46、ission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.