BS ISO 11218-2017 Aerospace Cleanliness classification for hydraulic fluids《航空航天 液压液的清洁度分类》.pdf

《BS ISO 11218-2017 Aerospace Cleanliness classification for hydraulic fluids《航空航天 液压液的清洁度分类》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 11218-2017 Aerospace Cleanliness classification for hydraulic fluids《航空航天 液压液的清洁度分类》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BS ISO 11218:2017Aerospace Cleanlinessclassification for hydraulicfluidsBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS ISO 11218:2017 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 11218:2017.The UK participation in its pre

2、paration was entrusted to Technical Committee ACE/69, Aerospace hydraulic systems, fluids and com-ponents.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users a

3、re responsible for its correct application. The British Standards Institution 2017.Published by BSI Standards Limited 2017ISBN 978 0 580 89375 9 ICS 49.080 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the

4、Standards Policy and Strategy Committee on 28 February 2017.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dBS ISO 11218:2017 ISO 2017Aerospace Cleanliness classification for hydraulic fluidsAronautique et espace Classes de propret des fluides hydrauliquesINTERNATIONAL STAN

5、DARDISO11218Second edition2017-02Reference numberISO 11218:2017(E)BS ISO 11218:2017ISO 11218:2017(E)ii ISO 2017 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2017, Published in SwitzerlandAll rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized

6、 otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright of

7、ficeCh. de Blandonnet 8 CP 401CH-1214 Vernier, Geneva, SwitzerlandTel. +41 22 749 01 11Fax +41 22 749 09 47copyrightiso.orgwww.iso.orgBS ISO 11218:2017ISO 11218:2017(E)Foreword iv1 Scope . 12 Normative references 13 Terms and definitions . 14 Requirements 15 Identification statement (reference to th

8、is document) . 16 Revision of AS4059F . 2 ISO 2017 All rights reserved iiiContents PageBS ISO 11218:2017ISO 11218:2017(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International St

9、andards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also

10、 take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In

11、 particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).Attention is drawn to the possibility that some of the eleme

12、nts of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received

13、 (see www .iso .org/ patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adhe

14、rence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www .iso .org/ iso/ foreword .html.The committee responsible for this document is ISO/TC 20, Aircraft and space vehicles, Subcommittee SC 10, Aerospace fluid systems and components.

15、This second edition cancels and replaces the first edition (ISO 11218:1993), which has been technically revised with the following change: references to AS 4059 have been updated.iv ISO 2017 All rights reservedBS ISO 11218:2017INTERNATIONAL STANDARD ISO 11218:2017(E)Aerospace Cleanliness classificat

16、ion for hydraulic fluids1 ScopeThis document specifies a cleanliness classification for hydraulic fluids in aeroplanes, helicopters and space vehicles.2 Normative referencesThe following documents are referred to in the text in such a way that some or all of their content constitutes requirements of

17、 this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.AS4059F, Aerospace fluid power Contamination classification for hydraulic fluids3 Terms and definitionsNo terms and definitio

18、ns are listed in this document.ISO and IEC maintain terminological databases for use in standardization at the following addresses: IEC Electropedia: available at h t t p :/ www .electropedia .org/ ISO Online browsing platform: available at h t t p :/ www .iso .org/ obp4 RequirementsRequirements are

19、 specified in SAE AS4059F1)which is adopted as a de facto ISO International Standard.For the purposes of international standardization, the modification outlined below shall apply to the specific clause of AS4059F.Page 12 Reference documentsAdd the following reference:ISO 5884, Aerospace Fluid Syste

20、ms and components Methods for system sampling and measuring the solid particle contamination of hydraulic fluids5 Identification statement (reference to this document)Use the following statement when electing to comply with ISO 11218:“Hydraulic fluid cleanliness classifications in accordance with IS

21、O 11218.”1) AS4059F is a copyrighted publication of the Society of Automotive Engineers (SAE). Copies of the original text in English are available from: Society of Automotive Engineers, 400, Commonwealth Drive, Warrendale, PA 15096-0001, USA. ISO 2017 All rights reserved 1BS ISO 11218:2017ISO 11218

22、:2017(E)6 Revision of AS4059FIt has been agreed with SAE that Technical Committee ISO/TC 20 will be consulted in the event of any revision or amendment of AS4059F.2 ISO 2017 All rights reservedBS ISO 11218:2017BS ISO 11218:2017ISO 11218:2017(E) ISO 2017 All rights reservedICS 49.080Price based on 2

23、pagesThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limi

24、ted.British Standards Institution (BSI)About usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable form

25、at and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by vi

26、siting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you n

27、eed international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.Copyright in BSI publicationsAll the content in BSI publications, including British Standards, is the property of and copyrighted by BSI or some person o

28、r entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use.Save for the provisions below, you may not transfer, share or disseminate any portion of the standard to any ot

29、her person. You may not adapt, distribute, commercially exploit, or publicly display the standard or any portion thereof in any manner whatsoever without BSIs prior written consent.Storing and using standardsStandards purchased in soft copy format: A British Standard purchased in soft copy format is

30、 licensed to a sole named user for personal or internal company use only. The standard may be stored on more than 1 device provided that it is accessible by the sole named user only and that only 1 copy is accessed at any one time. A single paper copy may be printed for personal or internal company

31、use only.Standards purchased in hard copy format: A British Standard purchased in hard copy format is for personal or internal company use only. It may not be further reproduced in any format to create an additional copy. This includes scanning of the document.If you need more than 1 copy of the doc

32、ument, or if you wish to share the document on an internal network, you can save money by choosing a subscription product (see Subscriptions).Reproducing extractsFor permission to reproduce content from BSI publications contact the BSI Copyright & Licensing team.SubscriptionsOur range of subscriptio

33、n services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is r

34、efreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscr

35、ibing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications

36、 on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendment or revision. We

37、continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.Useful ContactsCustomer ServicesTel: +44 345 086 9001Email (orders): Email (enquiries):

38、SubscriptionsTel: +44 345 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Group Headquarters389 Chiswick High Road London W4 4AL UKBSI Back Cover.indd 1 27/01/2016 14:20