BS ISO 11005-2010 Technical product documentation Use of main documents《技术产品文件 主要文件用途》.pdf

《BS ISO 11005-2010 Technical product documentation Use of main documents《技术产品文件 主要文件用途》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 11005-2010 Technical product documentation Use of main documents《技术产品文件 主要文件用途》.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS ISO 11005:2010Technical productdocumentation Use of maindocumentsBS ISO 11005:2010 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 11005

2、:2010.The UK participation in its preparation was entrusted to TechnicalCommittee TDW/4, Technical Product Realization.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contra

3、ct. Users are responsible for its correctapplication. BSI 2010ISBN 978 0 580 66006 1ICS 01.110Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 October 2010.Amend

4、ments issued since publicationDate Text affectedBS ISO 11005:2010Reference numberISO 11005:2010(E)ISO 2010INTERNATIONAL STANDARD ISO11005First edition2010-09-15Technical product documentation Use of main documents Documentation technique de produits Utilisation des documents principaux BS ISO 11005:

5、2010ISO 11005:2010(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In d

6、ownloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in

7、the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the addre

8、ss given below. COPYRIGHT PROTECTED DOCUMENT ISO 2010 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO

9、at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2010 All rights reservedBS ISO 11005:2010ISO 11005:201

10、0(E) ISO 2010 All rights reserved iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body

11、interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotech

12、nical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by t

13、he technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent right

14、s. ISO shall not be held responsible for identifying any or all such patent rights. ISO 11005 was prepared by Technical Committee ISO/TC 10, Technical product documentation, Subcommittee SC 1, Basic conventions. BS ISO 11005:2010BS ISO 11005:2010INTERNATIONAL STANDARD ISO 11005:2010(E) ISO 2010 All

15、rights reserved 1Technical product documentation Use of main documents 1 Scope This International Standard provides rules for the use of a main document in order to gather all the product-specifying information needed for a specific part or assembly. 2 Normative references The following referenced d

16、ocuments are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 7200:2004, Technical product documentation Data fields in title blocks

17、and document headers ISO 7573:2008, Technical product documentation Parts lists 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 document fixed and structured amount of information that can be managed and interchanged as a unit between users a

18、nd systems IEC 82045-1:2001, ISO 11442:2006 3.2 technical product document means of conveying all or part of a design definition or specification of a product for manufacturing, verification, maintenance, operation and recycling purposes, etc. 3.3 main document document containing the complete compi

19、lation of the information by which a part or an assembly is specified NOTE The information can be given directly in the main document or by reference to complementary documents. 3.4 complementary document document, referenced in the main document, containing specifying information BS ISO 11005:2010I

20、SO 11005:2010(E) 2 ISO 2010 All rights reserved3.5 part one piece of an assembly, or several pieces joined together which are not normally subject to disassembly without destruction 3.6 assembly number of component parts fitted together to perform a specific function ISO 7573:2008 NOTE Assembly incl

21、udes any level of complexity. 3.7 compound document document consisting of several embedded files in a specified file structure IEC 82045-1:2001 3.8 aggregated document document containing separately identified documents (parts) that are logically dependent but can be physically independently manage

22、d NOTE An aggregated document has its own metadata. IEC 82045-1:2001 3.9 document set collection of documents that are managed together as a unit for a specific purpose NOTE The metadata of the document set describes which documents it consists of. The set has its own metadata, but not its own conte

23、nt. IEC 82045-1:2001 4 General Technical product documents record the output of a design process. These documents, or parts of them, may be communicated to users such as customers, suppliers and production units. The technical product documents specify the requirements made with regard to an individ

24、ual part or an assembly. The main document is one essential part of the technical product documentation. This International Standard describes the contents of a main document and its relationship to complementary documents. 5 Main document principle The basis of the main document principle is that e

25、ach part or assembly is specified by a main document. When several documents are needed to specify a part or an assembly, one document shall be designated the main document to ensure that the information is kept together. All other documents, referred to in the main document, are considered compleme

26、ntary documents (see Figure 1). It is recommended that companies decide which document type(s) shall be adopted as the main document(s). This International Standard gives only a few examples of document types that may be used as main documents. BS ISO 11005:2010ISO 11005:2010(E) ISO 2010 All rights

27、reserved 3Main document Complementary documents LegalownerParts list18765431LegalownerAssembly drawing12345670LegalownerAssembly instruction10123456LegalownerTechnical Specification12345679The technical specification is atext-based document. This docu-ment type is used for statingrequirements for on

28、e specific partor for a group of parts with equalcharacteristics.This document type shouldcontain product requirementsand information needed forverification of these require-ments.1 1 18765432 Bracket2 1 18765433 Plate3 2 21234567 Hexagon head screw ISO 4017 M8x40 - 8.8 - A2F42521234568 Washer ISO 7

29、090-8-200 HV2 21234569 Hexagon nut ISO 4032 M8 - 8 - AFPart Qty Part number Part name Technical data, designation Remarkref.Technical specification: 12345679Assembly instruction: 23456790Assembly drawing: 12345670132 54Figure 1 Main and complementary documents relationship (example) In order to enab

30、le cross-use and reuse of information, there shall be no references to the main document in the complementary documents. This means that complementary documents are independent and can be used in different applications. However, if cross-using or reusing of documents are not needed, and there is a o

31、ne-to-one relationship between the main document and a complementary document, there could be a reference in a complementary document to a main document. When complementary documents are revised, the connection to main document(s) shall be shown by a where-used analysis. 6 Document content The main

32、document shall contain the part number and references to complementary documents when used. Furthermore, the parts list (see ISO 7573:2008), graphical representation, designations, classifications, technical data, properties, etc. are recorded either in the main document itself or in complementary d

33、ocuments. If the main document number and the part number are different, the part number shall be specified separately in the main document. The main document shall contain a title block or a document header (see ISO 7200:2004). The complementary documents could also specify separately documented re

34、quirements like geometry description, joining, dimensions, etc. 7 Relationship between main document and complementary documents 7.1 Main document Main documents are generally based on the following document types. One single document, e.g. a drawing (see Figure 2) including all information (no comp

35、lementary documents are needed). BS ISO 11005:2010ISO 11005:2010(E) 4 ISO 2010 All rights reservedThe complete information is available in one single document, which is therefore the main document. Main document LegalownerPart drawing10123456Material: Steel xxxxxxxxxSurface coating: yyyyyyyyMarking:

36、 zzzzzzzTechnical requirements:2 8,521020 40 420 40304540254Figure 2 One single document containing the complete information Compound document, e.g. assembly drawing and parts list (see Figure 3) in which the graphical and/or textual representation is predominant. Main document Complementary documen

37、ts LegalownerAssembly drawing12345678LegalownerAssembly instruction10123456LegalownerTechnical Specification12345679The technical specification is atext-based document. This docu-ment type is used for statingrequirements for one specific partor for a group of parts with equalcharacteristics.This doc

38、ument type shouldcontain product requirementsand information needed forverification of these require-ments.132 54Technical specification: 12345679Assembly instruction: 2345679052423 2 21234567 Screw21121234569 Nut ISO 4032 M8-8-AF21234568 Washer ISO 7090-8-200 HV18765433 Plate1 18765432 BracketRef Q

39、ty Part No Part name DataISO 4017 M8x40-8.8-A2FNOTE The complete information is available in a document set. The main document is a compound document consisting of an assembly drawing including a parts list and a document list referring to the complementary documents. Figure 3 An assembly drawing co

40、ntaining a parts list and a list of complementary documents BS ISO 11005:2010ISO 11005:2010(E) ISO 2010 All rights reserved 5Aggregated document (see Figure 4), e.g. assembly drawing and parts list including list of complementary documents. Main document Complementary documents LegalownerAssembly dr

41、awing18765431LegalownerAssembly instruction10123456LegalownerTechnical Specification12345679The technical specification is atext-based document. This docu-ment type is used for statingrequirements for one specific partor for a group of parts with equalcharacteristics.This document type shouldcontain

42、 product requirementsand information needed forverification of these require-ments.132 54LegalownerParts listPL187654311 1 18765432 Bracket2 1 18765433 Plate3 2 21234567 Hexagon head screw ISO 4017 M8x40 - 8.8 - A2F42521234568 Washer ISO 7090-8-200 HV2 21234569 Hexagon nut ISO 4032 M8 - 8 - AFPart Q

43、ty Part number Part name Technical data, designation Remarkref.Technical specification: 12345679Assembly instruction: 23456790PL18765431NOTE The complete information is available in a document set. The main document is an aggregated document consisting of an assembly drawing and a parts list that sp

44、ecifies constituents and all complementary documents. Figure 4 The main document being an aggregated document Parts list (see Figure 5), in which the parts list area is predominant. Main document Complementary documents LegalownerParts list18765431LegalownerAssembly drawing12345670LegalownerAssembly

45、 instruction10123456LegalownerTechnical Specification12345679The technical specification is atext-based document. This docu-ment type is used for statingrequirements for one specific partor for a group of parts with equalcharacteristics.This document type shouldcontain product requirementsand inform

46、ation needed forverification of these require-ments.1 1 18765432 Bracket2 1 18765433 Plate3 2 21234567 Hexagon head screw ISO 4017 M8x40 - 8.8 - A2F42521234568 Washer ISO 7090-8-200 HV2 21234569 Hexagon nut ISO 4032 M8 - 8 - AFPart Qty Part number Part name Technical data, designation Remarkref.Tech

47、nical specification: 12345679Assembly instruction: 23456790Assembly drawing: 12345670132 54NOTE The complete information is available in a document set. The main document is the parts list that specifies constituents and all complementary documents. Figure 5 Parts list including list of complementar

48、y documents BS ISO 11005:2010ISO 11005:2010(E) 6 ISO 2010 All rights reservedDocument list (see Figure 6), in which the complementary documents area is predominant. Main document Complementary documents LegalownerParts list123456711 1 18765432 Bracket2 1 18765433 Plate3 2 21234567 Hexagon head screw

49、 ISO 4017 M8x40 - 8.8 - A2F42521234568 Washer ISO 7090-8-200 HV2 21234569 Hexagon nut ISO 4032 M8 - 8 -AFPart Qty Part number Part name Technical data, designation Remarkref.LegalownerAssembly drawing12345670LegalownerAssembly instruction10123456LegalownerTechnical Specification12345679The technical specification is atext-based document. This docu-ment type is used for statingrequirements for one specific partor for a group of parts with equalcharacteristics.This document type shouldcontain product requirementsand