BS ISO 10458-1993 Textile machinery - Square bars for winding devices relating to dyeing and finishing machines - Dimensions《纺织机械 有关染整机械的络纱装置方形杆 尺寸》.pdf

《BS ISO 10458-1993 Textile machinery - Square bars for winding devices relating to dyeing and finishing machines - Dimensions《纺织机械 有关染整机械的络纱装置方形杆 尺寸》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 10458-1993 Textile machinery - Square bars for winding devices relating to dyeing and finishing machines - Dimensions《纺织机械 有关染整机械的络纱装置方形杆 尺寸》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS ISO 10458:1993 Implementation of ISO10458:1993 Textile machinery Square bars for winding devices relating to dyeing and finishing machines Dimensions UDC 677.057-229.7BSISO10458:1993 This BritishStandard, having been prepared under the directionof the Textiles and Clothing Standa

2、rds Policy Committee, was published underthe authority of the Standards Board and comes into effect on 15August1993 BSI 02-2000 The following BSI references relate to the work on this standard: Committee reference TCM/33 Draft for comment 90/47055 DC ISBN 0 580 22215 2 Committees responsible for thi

3、s BritishStandard The preparation of this BritishStandard was entrusted by the Textiles and Clothing Standards Policy Committee (TCM/-) to Technical Committee TCM/33, upon which the following bodies were represented: British Association of Clothing Machinery Manufacturers British Narrow Fabrics Asso

4、ciation British Paper and Board Industry Federation British Textile Machinery Association British Textile Technology Group Clothing and Footwear Institute Confederation of British Wool Textiles Limited Consumer Policy Committee of BSI Health and Safety Executive Knitting Industries Federation Ltd. T

5、extile Finishers Association Textile Institute Textile Research Council (HATRA) University of Manchester (Institute of Science and Technology) Amendments issued since publication Amd. No. Date CommentsBSISO10458:1993 BSI 02-2000 i Contents Page Committees responsible Inside front cover National fore

6、word ii Foreword iii Text of ISO10458 1BSISO10458:1993 ii BSI 02-2000 National foreword This BritishStandard reproduces verbatim ISO10458:1993 and implements it as the UK national standard. This BritishStandard is published under the direction of the Textiles and Clothing Standards Policy Committee

7、whose Technical Committee TCM/33 has the responsibility to: aid enquirers to understand the text; present to the responsible international committee any enquiries on interpretation, or proposals for change, and keep UK interests informed; monitor related international and European developments and p

8、romulgate them in the UK. NOTEInternational and European Standards, as well as overseas standards, are available from Customer Services. Publications, BSI, Linford Wood, Milton Keynes, MK146LE. A British Standard does not purport to include all the necessary provisions of a contract. Users of Britis

9、h Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, theISO title page, pages ii to iv, pages1 and 2 and a

10、back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.ISO10458:1993(E) ii BSI 02-2000 Contents Page Foreword iii 1 Scope 1 2 Normative reference 1 3 Types 1 4 Dimensions 1 5 De

11、signation 1 Figure 1 Square bars 1 Table 1 Dimensions of square bars 2ISO10458:1993(E) BSI 02-2000 iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normal

12、ly carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the

13、 work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requ

14、ires approval by at least75% of the member bodies casting a vote. International Standard ISO10458 was prepared by Technical Committee ISO/TC72, Textile machinery and allied machinery and accessories, Sub-Committee SC4, Dyeing, finishing and allied machinery and accessories.iv blankISO10458:1993(E) B

15、SI 02-2000 1 1 Scope This International Standard specifies the dimensions of the square section of bars of types A and B for winding devices relating to dyeing and finishing machines. 2 Normative reference The following standard contains provisions which, through reference in this text, constitute p

16、rovisions of this International Standard. At the time of publication, the edition indicated was valid. All standards are subject to revision, and parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent edition of the standa

17、rd indicated below. Members of IEC and ISO maintain registers of currently valid International Standards. ISO1505, Textile machinery Widths relating to dyeing and finishing machines Definitions and range of nominal widths 1) . 3 Types SeeFigure 1. 4 Dimensions SeeTable 1. 5 Designation The designati

18、on of a square bar for winding devices shall include the following information in the order given: a) “Square-bar”; b) reference to this International Standard (i.e.ISO10458); c) type of square bar (A or B); d) dimension b, in millimetres; e) dimension l 1 2) , in millimetres; f) dimension l 2 3)(on

19、ly for type A), in millimetres; g) dimension l 3 3)(only for type A), in millimetres. EXAMPLE1 A square bar for winding device, type A, with b=30mm, l 1 =1800mm,l 2 =300mm and l 3 =200mm shall be designated as follows: Square bar ISO10458-A30 1800 300 200 EXAMPLE2 A square bar for winding device, ty

20、pe B, with b=40mm and l 1 =1600mm shall be designated as follows: Square bar ISO10458-B40 1600 1) To be published. (Revision of ISO1505:1982) 2) Preferably chosen from the values given in ISO1505. 3) To be agreed between the user and manufacturer. NOTEThe values for l 1 , l 2and l 3depend on the con

21、struction and the nominal width of the machine and shall be agreed between the user and manufacturer. It is recommended that the values of l 1be chosen from the nominal widths given in ISO1505. Figure 1 Square barsISO10458:1993(E) 2 BSI 02-2000 Table 1 Dimensions of square bars Dimensions in millime

22、tres b d a 25 20 30 25 40 35 50 45 Further steps shall be in increments of10mm a Recommended values. Other values may be agreed between the user and manufacturer.blankBS ISO 10458:1993 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body respon

23、sible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendment

24、s or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found o

25、n the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications shoul

26、d be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide

27、range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111.

28、 Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists

29、 in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any me

30、ans electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.