BS ISO 10372-1998 Hydraulic fluid power - Four-and five-port servovalves - Mounting surfaces《液压流体动力 4孔和5孔伺服阀 安装面》.pdf

《BS ISO 10372-1998 Hydraulic fluid power - Four-and five-port servovalves - Mounting surfaces《液压流体动力 4孔和5孔伺服阀 安装面》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 10372-1998 Hydraulic fluid power - Four-and five-port servovalves - Mounting surfaces《液压流体动力 4孔和5孔伺服阀 安装面》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS ISO 10372:1992 Hydraulic fluid power Four-and five-port servovalves Mounting surfaces ICS 23.100.30BSISO10372:1992 This British Standard, having been prepared under the direction of the Engineering Sector Board, was published under the authority of the Standards Board and comesin

2、toeffect on 15October1998 BSI 05-1999 ISBN 0 580 30492 2 National foreword This British Standard reproduces verbatimISO10372:1992 and implements it as the UK national standard. It supersedesBS6494-2:1986 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee

3、MCE/18, Fluid power systems and components, which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related internation

4、al and European developments and promulgate them in the UK. A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in th

5、e BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are re

6、sponsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, theISO title page, page ii, pages1 to7 and a back cover. This standard

7、 has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No. Date CommentsBSISO10372:1992 BSI 05-1999 i Contents Page National foreword Inside front cover Forewor

8、d ii Introduction 1 1 Scope 1 2 Normative references 1 3 Definitions 1 4 Symbols 1 5 Tolerances 1 6 Dimensions 1 7 Pressure limitations 2 8 Locating pin 2 9 Identification statement 2 Figure 1 Mounting surface dimensions for four-port servovalves with3,8 mm maximum port diameter 3 Figure 2 Mounting

9、surface dimensions for four-port servovalves with5 mm maximum port diameter 4 Figure 3 Mounting surface dimensions for four-port servovalves with6,6 mm maximum port diameter 5 Figure 4 Mounting surface dimensions for four-port servovalves with8,2 mm maximum port diameter 6 Figure 5 Mounting surface

10、dimensions for four-port servovalves with16 mm maximum port diameter 7 Table 1 Recommended locating-pin diameters 2 Table 2 Mounting surface dimensions for four-port servovalves with3,8 mm maximum port diameter 3 Table 3 Mounting surface dimensions for four-port servovalves with5 mm maximum port dia

11、meter 4 Table 4 Mounting surface dimensions for four-port servovalves with6,6 mm maximum port diameter 5 Table 5 Mounting surface dimensions for four-port servovalves with8,2 mm maximum port diameter 6 Table 6 Mounting surface dimensions for four-port servovalves with16 mm maximum port diameter 7ii

12、blankBSISO10372:1992 ii BSI 05-1999 Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body i

13、nterested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison withISO, also take part in the work. ISO collaborates closely with the International Electrotechni

14、cal Commission (IEC) on all matters of electrotechnical standardization. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least75% of the member bodies casting a vote. In

15、ternational StandardISO10372 was prepared by Technical Committee ISO/TC131, Fluid power systems, Sub-CommitteeSC5, Control products and components. Descriptors: Hydraulic fluid power, hydraulic equipment, hydraulic servomechanisms, valves, hydraulic valves, mounting surfaces, dimensions, dimensional

16、 tolerances, interchangeability.BSISO10372:1992 BSI 05-1999 1 Introduction In hydraulic fluid power systems, power is transmitted and controlled through a liquid under pressure within an enclosed circuit. Typical components found in such systems include servovalves. 1 Scope This International Standa

17、rd specifies the dimensions of surfaces on which servovalves are mounted in order to ensure interchangeability. It applies primarily to electrohydraulic flow-control servovalves which represent current industrial practice. It is applicable to four-port servovalves and also to five-port types, i.e. t

18、hose in which the pilot stage is supplied with hydraulic fluid separately from the remaining stages. In addition, this International Standard may be used for pressure-control servovalves. If the valve is used in a three-port application, either service port (AandB) may be omitted. Because there is n

19、o clear distinction between servovalves and certain proportional control valves in performance and/or application, the existence of this mounting surface for servovalves does not exclude the use of a mounting surface as specified inISO4401. 2 Normative references The following standards contain prov

20、isions which, through reference in this text, constitute provisions of this International Standard. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this International Standard are encouraged to investigate the p

21、ossibility of applying the most recent editions of the standards indicated below. Members ofIEC andISO maintain registers of currently valid International Standards. ISO 468:1982, Surface roughness Parameters, their values and general rules for specifying requirements. ISO 1101:1983, Technical drawi

22、ngs Geometrical tolerancing Tolerances of form, orientation, location and run-out Generalities, definitions, symbols, indications on drawings. ISO 1302:1992, Technical drawings Method of indicating surface texture. ISO 4401:1980, Hydraulic fluid power Four-port directional control valves Mounting su

23、rfaces. ISO 5598:1985, Fluid power systems and components Vocabulary. ISO 5783:1981, Hydraulic fluid power Code for identification of valve mounting surfaces. ISO 9461:1992, Hydraulic fluid power Identification of valve ports, subplates, control devices and solenoids. 3 Definitions For the purposes

24、of this International Standard, the definitions given in ISO 5598 apply. 4 Symbols For the purposes of this International Standard, the following symbols apply: A, B, P, T and X identify ports in accordance withISO9461; F 1 , F 2 , F 3and F 4identify threaded holes for fixing screws; G identifies a

25、locating pin hole; r maxidentifies the mounting surface edge radius. 5 Tolerances 5.1 The following values shall be applied to the mounting surfaces: surface roughness: R a 0,8 4m (N6), as specified inISO468 andISO1302 surface flatness: 0,025 mm as specified inISO1101 5.2 The following tolerance sha

26、ll be complied with along the x and y axes with respect to the origin: pin holes, port holes and bolt holes: 0,2 mm As for other dimensions, see the figures. 6 Dimensions The mounting surface dimensions for servovalves with four or five ports shall be selected from the figures and tables specified i

27、n 6.1 to 6.5. 6.1 Mounting surface dimensions for four-port servovalves with3,8 mm maximum port diameter(10372 01 01 0 92) 1)are given in Figure 1 and Table 2. 6.2 Mounting surface dimensions for four-port servovalves with5mm maximum port diameter(10372 02 02 0 92) 1)are given in Figure 2 and Table

28、3. 6.3 Mounting surface dimensions for four-port servovalves with6,6mm maximum port diameter(10372 03 03 0 92) 1)are given in Figure 3 and Table 4. 1) For the explanation of codes, seeISO5783.BSISO10372:1992 2 BSI 05-1999 6.4 Mounting surface dimensions for four-port servovalves with8,2 mm maximum p

29、ort diameter(10372 04 04 0 92) 2)are given in Figure 4 and Table 5. 6.5 Mounting surface dimensions for four-port servovalves with16 mm maximum port diameter(10372 06 05 0 92) 2)are given in Figure 5 and Table 6. NOTE 1Use the dimensions for the pilot supply port X only if the pilot stage is supplie

30、d with hydraulic fluid separately from other stages. 7 Pressure limitations Operating pressure limitations for subplates and manifold blocks with these mounting surfaces will be specified by the manufacturer. 8 Locating pin Recommended locating-pin diameters are given in terms of locating-pin hole d

31、iameters in Table 1. Table 1 Recommended locating-pin diameters 9 Identification statement (Reference to this International Standard) Use the following statement in tests reports, catalogues and sales literature when electing to comply with this International Standard: “Mounting surface dimensions c

32、onform toISO10372:1992, Hydraulic fluid power Four- and five-port servovalves Mounting surfaces.” 2) For the explanation of codes, seeISO5783. Dimensions in millimetres Diameters of locating-pin hole G of locating pin 2,5 1,5 3,5 2,5 8 6BSISO10372:1992 BSI 05-1999 3 Table 2 Mounting surface dimensio

33、ns for four-port servovalves with3,8 mm maximum port diameter Figure 1 Mounting surface dimensions for four-port servovalves with3,8 mm maximum port diameter Dimensions in millimetres Axis P A T B G F 1 F 2 F 3 F 4 ? 3,8 max. ? 3,8 max. ? 3,8 max. ? 3,8 max. ? 2,5 M4 M4 M4 M4 x 11,9 5,8 11,9 18 4,8

34、0 23,8 23,8 0 y 7 13,1 19,2 13,1 6 0 0 26,2 26,2BSISO10372:1992 4 BSI 05-1999 Table 3 Mounting surface dimensions for four-port servovalves with5 mm maximum port diameter Figure 2 Mounting surface dimensions for four-port servovalves with5 mm maximum port diameter Dimensions in millimetres Axis P A

35、T B G F 1 F 2 F 3 F 4 ? 5 max. ? 5 max. ? 5 max. ? 5 max. ? 3,5 M5 M5 M5 M5 x 21,4 13,5 21,4 29,3 11,5 0 42,8 42,8 0 y 9,2 17,1 25 17,1 4,4 0 0 34,2 34,2BSISO10372:1992 BSI 05-1999 5 Table 4 Mounting surface dimensions for four-port servovalves with6,6 mm maximum port diameter Figure 3 Mounting surf

36、ace dimensions for four-port servovalves with6,6 mm maximum port diameter Dimensions in millimetres Axis P A T B G F 1 F 2 F 3 F 4 ? 6,6 max. ? 6,6 max. ? 6,6 max. ? 6,6 max. ? 3,5 M6 M6 M6 M6 x 21,4 11,5 21,4 31,3 11,5 0 42,8 42,8 0 y 7,2 17,1 27 17,1 4,4 0 0 34,2 34,2BSISO10372:1992 6 BSI 05-1999

37、Table 5 Mounting surface dimensions for four-port servovalves with8,2 mm maximum port diameter Figure 4 Mounting surface dimensions for four-port servovalves with8,2 mm maximum port diameter Dimensions in millimetres Axis P A T B G X F 1 F 2 F 3 F 4 ? 8,2 max. ? 8,2 max. ? 8,2 max. ? 8,2 max. ? 3,5

38、? 5 M8 M8 M8 M8 x 22,2 11,1 22,2 33,3 12,3 33,3 0 44,4 44,4 0 y 21,4 32,5 43,6 32,5 19,8 8,7 0 0 65 65BSISO10372:1992 BSI 05-1999 7 Table 6 Mounting surface dimensions for four-port servovalves with16 mm maximumportdiameter Figure 5 Mounting surface dimensions for four-port servovalves with16 mm max

39、imum port diameter Dimensions in millimetres Axis P A T B G X F 1 F 2 F 3 F 4 ? 16 max. ? 16 max. ? 16 max. ? 16 max. ? 8 ? 5 max. M10 M10 M10 M10 x 36,5 11,1 36,5 61,9 11,1 55,6 0 73 73 0 y 17,4 42,8 68,2 42,8 23,7 4,6 0 0 85,6 85,6BS ISO 10372:1992 BSI 389 Chiswick High Road London W4 4AL BSIBriti

40、shStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of Britis

41、hStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the tec

42、hnical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders f

43、or all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless

44、otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its produ

45、cts and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administrati

46、on. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the internationalstandardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, sto

47、red in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or gr

48、ade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.