BS ISO 10110-11-2016 Optics and photonics Preparation of drawings for optical elements and systems Non-toleranced data《光学及光学仪器 光学元件和系统图纸的制备 非公差数据》.pdf

《BS ISO 10110-11-2016 Optics and photonics Preparation of drawings for optical elements and systems Non-toleranced data《光学及光学仪器 光学元件和系统图纸的制备 非公差数据》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 10110-11-2016 Optics and photonics Preparation of drawings for optical elements and systems Non-toleranced data《光学及光学仪器 光学元件和系统图纸的制备 非公差数据》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BS ISO 10110-11:2016Optics and photonics Preparation of drawings foroptical elements and systemsPart 11: Non-toleranced dataBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS ISO 10110-11:2016 BRITISH STANDARDNational forewordThis British Standard is the UK implement

2、ation of ISO10110-11:2016. It supersedes BS ISO 10110-11:1996 which iswithdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee CPW/172, Optics and Photonics.A list of organizations represented on this committee can beobtained on request to its secretary.This publication

3、does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2016. Published by BSI StandardsLimited 2016ISBN 978 0 580 89374 2ICS 01.100.20; 37.020Compliance with a British Standard cannot confer immunity

4、fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 July 2016.Amendments issued since publicationDate Text affectedBS ISO 10110-11:2016 ISO 2016Optics and photonics Preparation of drawings for optical elements and systems

5、Part 11: Non-toleranced dataOptique et photonique Indications sur les dessins pour lments et systmes optiques Partie 11: Donnes non tolrancesINTERNATIONAL STANDARDISO10110-11Second edition2016-07-15Reference numberISO 10110-11:2016(E)BS ISO 10110-11:2016ISO 10110-11:2016(E)ii ISO 2016 All rights res

6、ervedCOPYRIGHT PROTECTED DOCUMENT ISO 2016, Published in SwitzerlandAll rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an int

7、ranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCh. de Blandonnet 8 CP 401CH-1214 Vernier, Geneva, SwitzerlandTel. +41 22 749 01 11Fax +41 22 749 09 47copyrightiso.orgwww

8、.iso.orgBS ISO 10110-11:2016ISO 10110-11:2016(E)Foreword ivIntroduction vi1 Scope . 12 Normative references 13 Permissible deviations and material imperfections . 1Bibliography 3 ISO 2016 All rights reserved iiiContents PageBS ISO 10110-11:2016ISO 10110-11:2016(E)ForewordISO (the International Organ

9、ization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been establish

10、ed has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.

11、The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the

12、 editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any paten

13、t rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For a

14、n explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary informationThe committee responsible for thi

15、s document is ISO/TC 172, Optics and photonics, Subcommittee SC 1, Fundamental standards.This second edition cancels and replaces the first edition (ISO 10110-11:1996), which has been technically revised. It also incorporates the Corrigendum (ISO 10110-11:1996/Cor.1:2006).The following changes were

16、made.a) Additional categories have been added for categories not included in the former version. New parameters specified are clear aperture to part edge, mean index of refraction tolerance, and Abbe number error. Some terminology has also been updated as well.b) Some numbers have been updated to re

17、flect common shop practice, with the intent that the numbers given here represent “loose” values for traditional optical fabrication processes at given sizes. This part of ISO 10110 covers cases where numbers are not included and assuming less stringent requirements is the default for non-toleranced

18、 data.c) Referenced normative and other ISO 10110 documents have been updated appropriately.ISO 10110 consists of the following parts, under the general title Optics and photonics Preparation of drawings for optical elements and systems: Part 1: General Part 2: Material imperfections Stress birefrin

19、gence Part 3: Material imperfections Bubbles and inclusions Part 4: Material imperfections lnhomogeneity and striae Part 5: Surface form tolerances Part 6: Centring tolerancesiv ISO 2016 All rights reservedBS ISO 10110-11:2016ISO 10110-11:2016(E) Part 7: Surface imperfection tolerances Part 8: Surfa

20、ce texture; roughness and waviness Part 9: Surface treatment and coating Part 10: Table representing data of optical elements and cemented assemblies Part 11: Non-toleranced data Part 12: Aspheric surfaces Part 14: Wavefront deformation tolerance Part 17: Laser irradiation damage threshold Part 19:

21、General description of surfaces and components ISO 2016 All rights reserved vBS ISO 10110-11:2016ISO 10110-11:2016(E)IntroductionNon-toleranced data covers cases where information required to fabricate optical components is not included on drawings. It is effectively the default values for the stand

22、ard, dependent on size of the optic for many of the values. Because these values are the default, they are intentionally chosen to be values deemed as loose fabrication requirements for industry. These values do not represent absolute limits, however, and can be made looser for given drawings and ap

23、plication.The current revision is an update to the 1996 edition of this part of ISO 10110. This version includes a few additional parameters and has magnitudes of some values updated. The values are intended to represent reasonable loose quantities for current standard practice optical fabrication w

24、ith traditional methodology. Although it is quite difficult to come up with universal values representing such standard practice, it is important to have quantities defined as defaults for cases where such information is not included on drawings, whether unintentional or by design choice.vi ISO 2016

25、 All rights reservedBS ISO 10110-11:2016INTERNATIONAL STANDARD ISO 10110-11:2016(E)Optics and photonics Preparation of drawings for optical elements and systems Part 11: Non-toleranced data1 ScopeISO 10110 specifies the presentation of design and functional requirements for optical elements and syst

26、ems in technical drawings used for manufacturing and inspection.This part of ISO 10110 specifies the permissible deviations and material imperfections when these are not explicitly indicated.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this docume

27、nt and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 10110-2, Optics and optical instruments Preparation of drawings for optical elements and sy

28、stems Part 2: Material imperfections Stress birefringenceISO 10110-3, Optics and optical instruments Preparation of drawings for optical elements and systems Part 3: Material imperfections Bubbles and inclusionsISO 10110-4, Optics and optical instruments Preparation of drawings for optical elements

29、and systems Part 4: Material imperfections Inhomogeneity and striaeISO 10110-5, Optics and photonics Preparation of drawings for optical elements and systems Part 5: Surface form tolerancesISO 10110-6, Optics and photonics Preparation of drawings for optical elements and systems Part 6: Centring tol

30、erancesISO 10110-7, Optics and photonics Preparation of drawings for optical elements and systems Part 7: Surface imperfection tolerancesISO 10110-8, Optics and photonics Preparation of drawings for optical elements and systems Part 8: Surface texture; roughness and waviness3 Permissible deviations

31、and material imperfectionsComplete functional properties of an optical element, dimensions and tolerances as well as surface and material properties should be indicated in optical drawings.The permissible deviations and material imperfections are given in Table 1 when such quantities are not specifi

32、ed in drawings.NOTE ln cases in which the values given in Table 1 are appropriate, the drawing can be simplified by omission of their indications.These tolerances do not represent absolute limits. Even looser tolerances may be used; however, they shall then be indicated in the drawing. ISO 2016 All

33、rights reserved 1BS ISO 10110-11:2016ISO 10110-11:2016(E)If a drawing of an optical part contains no indication of qualities mentioned in the various parts of ISO 10110, the values of Table 1 shall be applied. The surface texture specifications for an optical element in accordance with ISO 10110-8 s

34、hall always be given in the drawing; no implicit indication for surface texture is therefore given in this part of ISO 10110.Table 1 Permissible deviations and material imperfections in case explicit indications are not givenPropertyRange of maximum (diagonal) dimension of the partmm2up to 10over 10

35、up to 30over 30up to 100over 100up to 300Part diameter or edge length (mm)+0/ 0,15 +0/ 0,15 +0/ 0,75 +0,2/ 1,5Clear aperture to part edge (mm) 0,5 1 1 2Thickness (mm) 0,1 0,2 0,4 0,8Angle deviation of prisms and plate0 30 0 30 0 30 0 30Width of protective chamfer (mm)0,1 to 0,3 0,3 to 0,5 0,3 to 0,8

36、 0,8 to 1,6Principal refractive index 2,0 10-32,0 10-32,0 10-32,0 10-3Abbe number 0,8 % 0,8 % 0,8 % 0,8 %Stress birefringence in accordance with ISO 10110-2 (nm/cm)0/20 0/20 0/30 0/40Bubbles and inclusions in accordance with ISO 10110-31/3 0,16 1/5 0,25 1/5 0,4 1/5 0,63lnhomogeneity and striae in ac

37、cordance with ISO 10110-42/1;1 2/1;1 2/0;1 2/0;1Surface form tolerances in accordance with ISO 10110-53/5(1) 3/5(2)3/5(2)(all 30 mm)3/8(2)(all 60 mm)Centring tolerances in accordance with ISO 10110-64/20 4/10 4/10 4/10Surface imperfections in accordance with ISO 10110-75/3 0,16 5/5 0,25 5/5 0,4 5/5

38、0,63NOTE 1 This part of ISO 10110 does not provide implicit specifications for laser irradiation damage threshold (see ISO 10110-17), or additional surface imperfections for coated optics for edge chips (see ISO 10110-7).NOTE 2 Default numbers apply to the finished part.NOTE 3 Principal refractive i

39、ndex and Abbe number variation may be assessed at convenient wavelength values because differences between these parameters at different wavelengths is assumed to be inconsequential for non-toleranced data (see ISO 12123).2 ISO 2016 All rights reservedBS ISO 10110-11:2016ISO 10110-11:2016(E)Bibliogr

40、aphy1 ISO 7944, Optics and optical instruments Reference wavelengths2 ISO 10110-17, Optics and photonics Preparation of drawings for optical elements and systems Part 17: Laser irradiation damage threshold3 ISO 12123, Optics and photonics Specification of raw optical glass ISO 2016 All rights reserv

41、ed 3BS ISO 10110-11:2016ISO 10110-11:2016(E) ISO 2016 All rights reservedICS 37.020; 01.100.20Price based on 3 pagesThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorpor

42、ated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)About usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into stand

43、ards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can prov

44、ide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted

45、European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.Copyright in BSI publicationsAll the conte

46、nt in BSI publications, including British Standards, is the property of and copyrighted by BSI or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use.

47、Save for the provisions below, you may not transfer, share or disseminate any portion of the standard to any other person. You may not adapt, distribute, commercially exploit, or publicly display the standard or any portion thereof in any manner whatsoever without BSIs prior written consent.Storing

48、and using standardsStandards purchased in soft copy format: A British Standard purchased in soft copy format is licensed to a sole named user for personal or internal company use only. The standard may be stored on more than 1 device provided that it is accessible by the sole named user only and tha

49、t only 1 copy is accessed at any one time. A single paper copy may be printed for personal or internal company use only.Standards purchased in hard copy format: A British Standard purchased in hard copy format is for personal or internal company use only. It may not be further reproduced in any format to create an additional copy. This includes scanning of t