BS ISO 1004-2-2013 Information processing Magnetic ink character recognition Print specifications for CMC7《信息处理 磁性墨水字符识别 CMC7的打印规范》.pdf

《BS ISO 1004-2-2013 Information processing Magnetic ink character recognition Print specifications for CMC7《信息处理 磁性墨水字符识别 CMC7的打印规范》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 1004-2-2013 Information processing Magnetic ink character recognition Print specifications for CMC7《信息处理 磁性墨水字符识别 CMC7的打印规范》.pdf（42页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS ISO 1004-2:2013Information processing Magnetic ink characterrecognitionPart 2: Print specifications for CMC7BS ISO 1004-2:2013 BRITISH STANDARDNational forewordThis British St

2、andard is the UK implementation of ISO 1004-2:2013.The UK participation in its preparation was entrusted to TechnicalCommittee IST/12, Financial services.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all

3、the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2013. Published by BSI StandardsLimited 2013ISBN 978 0 580 78111 7ICS 35.240.40Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Stand

4、ard was published under the authority of theStandards Policy and Strategy Committee on 30 June 2013.Amendments issued since publicationDate Text affectedBS ISO 1004-2:2013 ISO 2013Information processing Magnetic ink character recognition Part 2: Print specifications for CMC7Traitement de linformatio

5、n Reconnaissance des caractres encre magntique Partie 2: Spcifications dimpression CMC7INTERNATIONAL STANDARDISO1004-2First edition2013-06-01Reference numberISO 1004-2:2013(E)BS ISO 1004-2:2013ISO 1004-2:2013(E)ii ISO 2013 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2013All rights reserved.

6、Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at t

7、he address below or ISOs member body in the country of the requester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 1004-2:2013ISO 1004-2:2013(E) ISO 2013 All rights reserved iiiCont

8、ents PageForeword iv1 Scope . 12 Normative references 13 Terms, definitions, symbols and abbreviations . 13.1 Terms and definitions . 13.2 Symbols and abbreviations 24 Character configuration 34.1 Code description 34.2 Configuration 35 Means of automatic sensing 46 Reference edges of documents 47 Pr

9、int location 47.1 Horizontal location 47.2 Vertical location 48 Clear band 49 Character spacing and alignment . 59.1 Horizontal character spacing 59.2 Vertical misalignment . 510 Character definition and tolerances 510.1 Definitions . 510.2 Stroke edge zones and mean edges . 610.3 Skew angle .610.4

10、Stroke width L .610.5 Stroke interval P 611 Extraneous ink (spots) .711.1 Extraneous ink front 711.2 Extraneous ink back . 712 Voids 713 Segment end zones .714 Uniformity of ink 715 Debossment . 816 Signal level 816.1 Description of the signal . 816.2 Definitions relating to signal level 816.3 Allow

11、able signal level range 816.4 Nominal signal level . 916.5 Residual signal level . 917 Paper . 918 MICR ink permanence . 919 Drawings of the printed characters of Font CMC 7 .10Annex A (informative) Use of CMC7 Symbols 32BS ISO 1004-2:2013ISO 1004-2:2013(E)ForewordISO (the International Organization

12、 for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has

13、the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The pro

14、cedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editor

15、ial rules of the ISO/IEC Directives, Part 2. www.iso.org/directivesAttention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights ident

16、ified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received. www.iso.org/patentsAny trade name used in this document is information given for the convenience of users and does not constitute an endorsement.The committee responsible

17、for this document is ISO/TC 68, Financial services, Subcommittee SC 7, Core banking.This first edition of ISO 1004-2, together with ISO 1004-1, cancels and replaces ISO 1004:1995, which has been technically revised.ISO 1004 consists of the following parts, under the general title Information process

18、ing Magnetic ink character recognition: Part 1: Print specifications for E13B Part 2: Print specifications for CMC7Annex A is for information only.iv ISO 2013 All rights reservedBS ISO 1004-2:2013INTERNATIONAL STANDARD ISO 1004-2:2013(E)Information processing Magnetic ink character recognition Part

19、2: Print specifications for CMC71 ScopeThis part of ISO 1004 specifies the shapes, dimensions and tolerances for the 10 digits 0 to 9, five symbols, and 26 letters, to be printed with magnetic ink for the purpose of character recognition. It describes the various types of printing defects and other

20、printing considerations, together with the tolerances permitted, and also contains specifications to signal level measurement.The characters specified in Clause 4 of this part of ISO 1004 were developed initially for use in banks to permit automatic document handling for bank data processing, but th

21、ey have application to other automatic processing systems as well.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, t

22、he latest edition of the referenced document (including any amendments) applies.”ISO 1004-1:2013, Information processing Magnetic ink character recognition Part 1: Print specifications for E13B3 Terms, definitions, symbols and abbreviations3.1 Terms and definitionsFor the purposes of this document,

23、the following terms and definitions apply.3.1.1magnetic inkink capable of being magnetized and sensed3.1.2vertical misalignmentdeviation of the printed character from the nominal vertical position on the document3.1.3voidabsence of magnetic ink outside the printed edge zone and outside the segment e

24、nd zones in an area that should be inked3.1.4segment end zoneszone of maximum height of 0,22 mm that can be located at both ends of strokes and stroke segments3.1.5residual signal levelmaximum signal level delivered by a character which has been voided ISO 2013 All rights reserved 1BS ISO 1004-2:201

25、3ISO 1004-2:2013(E)3.2 Symbols and abbreviationsSymbol or abbreviationCorresponding clause or subclauseCharacteristicA 9.1.4 Character widthA19.1.4 Character width of a character with one long intervalA29.1.4 Character width of a character with two long intervalsA39.1.4 Character width of a characte

26、r with three long intervalsAL9 Alignmentb 10.2.1 Printed edge zone widthB 9.1.1 Character pitchCB 8 Clear bandD 9.1.2 Intercharacter distanceDm9.1.1 Minimum interchange distanceDm19.1.3Minimum interchange distance for character with one or two long inter-valsDm29.1.3 Minimum interchange distance for

27、 character with three long intervalsDM 15 DebossmentExB 11.2 Extraneous ink backExF 11.1 Extraneous ink frontFT 18 Formath 10.1.2 Segment heightHc10.1.4 Character heightHf10.1.5 Font heightL 10.4 Stroke widthM 10.1.3 Stroke heightP 10.5 Stroke intervalPL110.5.2 Short stroke interval between left mea

28、n edgesPL210.5.2 Long stroke interval between right mean edgesPR110.5.1 Short stroke interval between right mean edgesPR210.5.1 Long stroke interval between right mean edgesSP 9 Character spacingUI 14 Uniformity of inkV 12 Voids2 ISO 2013 All rights reservedBS ISO 1004-2:2013ISO 1004-2:2013(E)Symbol

29、 or abbreviationCorresponding clause or subclauseCharacteristicVM 9.2 Vertical misalignment 10.3 Character skew angle4 Character configuration4.1 Code descriptionThe coded character is composed of six intervals contained within seven strokes cut to the shape of a conventional character.Two interval

30、widths are used: “long” and “short”. It is the combination of these “long” and “short” intervals that determines the character code.Two long and four short intervals may be combined in 15 possible ways (C62) a total which is available for the 10 digits and five symbols.The alphabetic code uses one o

31、r three long intervals, allowing a total of C61+ C63= 26 combinations which are thus available for 26 letters.Table1 shows the correspondence between codes and the characters. The intervals are numbered 1 to 6 from left to right on the printed character. Their values are represented by the digit 0 f

32、or short intervals and by the digit 1 for long intervals.4.2 ConfigurationThere are four font heights (see 10.1.5): 3,20 mm, 3,00 mm, 2,85 mm and 2,70 mm. Figures 3 to 23 give full details of the alphanumeric character set and symbols.Table 1 Character code description (0 = short interval. 1 = long

33、interval)Interval patternCoded characterInterval patternCoded character1 2 3 4 5 6 1 2 3 4 5 61 0 0 0 1 0 1 0 1 0 0 0 0 A0 1 1 0 0 0 2 1 0 1 0 1 0 B1 0 1 0 0 0 3 0 0 0 1 1 1 C1 0 0 1 0 0 4 1 0 0 1 1 0 D0 0 0 1 1 0 5 0 0 0 1 0 0 E0 0 1 0 1 0 6 0 0 1 0 1 1 F1 1 0 0 0 0 7 1 0 0 0 1 1 G0 1 0 0 1 0 8 1 0

34、 1 1 0 0 H0 1 0 1 0 0 9 0 0 0 0 0 1 I0 0 1 1 0 0 0 1 0 1 0 0 1 J1 0 0 0 0 1 S I 0 1 1 0 1 0 K0 1 0 0 0 1 S II 0 1 0 0 1 1 L0 0 1 0 0 1 S III 0 0 1 1 1 0 M0 0 0 1 0 1 S IV 0 0 1 0 0 0 N0 0 0 0 1 1 S V 1 0 0 0 0 0 O ISO 2013 All rights reserved 3BS ISO 1004-2:2013ISO 1004-2:2013(E)Interval patternCode

35、d characterInterval patternCoded character1 2 3 4 5 6 1 2 3 4 5 60 1 0 1 1 0 P1 1 1 0 0 0 Q0 1 1 1 0 0 R0 1 0 1 0 1 S0 0 0 0 1 0 T1 1 0 1 0 0 U1 1 0 0 0 1 V1 0 0 1 0 1 W1 1 0 0 1 0 X0 1 1 0 0 1 Y0 0 1 1 0 1 Z5 Means of automatic sensingThe automatic character recognition takes place by means of iden

36、tification of the interval lengths between adjacent strokes. Stroke sensing takes place magnetically.6 Reference edges of documentsFor the purpose of measuring the printed image, the right-hand and the bottom edges are the reference edges of the document.7 Print location7.1 Horizontal locationThe ex

37、treme right mean edge of the printed line should be located at least 6,0 mm from the right reference edge of the document. The distance between the left-hand edge of the document and the extreme left mean edge in the printed line should be at least 4,0 mm. In some cases, by agreement between parties

38、 concerned, this latter distance may be reduced to 2,0 mm. System consideration may dictate a 6,0 mm minimum margin on both sides, if the document is to be readable in both directions. (See Figure 1).7.2 Vertical locationThe character shall be printed entirely within a printing band 6,4 mm high. The

39、 bottom edge of this printing band is located 4,8 mm above and parallel to the bottom reference edge of the document. (See Figure 1).This subclause does not apply to punched cards.8 Clear bandOver the whole length and on both sides of the document a clear band, 16 mm measured from the bottom edge of

40、 the document, shall be free from any magnetic ink other than CMC 7 character (see Figure 1). Under no circumstances may CMC 7 characters be printed within the clear band using non-magnetic ink.CMC 7 and E13 B fonts shall not be permitted in the same clear bank on any document. CMC 7 shall only appe

41、ar on the front of the document.Table 1 (continued)4 ISO 2013 All rights reservedBS ISO 1004-2:2013ISO 1004-2:2013(E)9 Character spacing and alignment9.1 Horizontal character spacing9.1.1 Character pitch, BThe distance between the orthogonal projections upon the bottom reference edge of the extreme

42、right mean edges (see 10.2.2) at mid-character height of adjacent characters. The nominal character pitch B may be as small as 3,17 mm . The horizontal spacing between characters shall be such that a minimum inter-character distance Dmis maintained.9.1.2 Intercharacter distance D between two adjacen

43、t charactersThe distance between the orthogonal projections upon the bottom reference edge of the right mean edges (see 10.2.2) at mid-character height of the left-hand stroke of the right-hand character and the right-hand stroke of the left-hand character.9.1.3 Minimum inter character distanceDm1=

44、0,67 mm if the right-hand character has one or two long intervals: and Dm2= 0,50 mm if the right-hand character has three long intervals.9.1.4 Character width AThe distance between the right mean edges of the outer most strokes of a character. The nominal values for characters with one, two and thre

45、e long intervals respectively, are as follows:A1= 2,0 mm A2= 2,2 mm A3= 2,4 mm 9.2 Vertical misalignmentVertical misalignment should be consistent with good printing practice and can be tolerated as far as the characters are completely contained in the printing band of the document. (See 7.2 and Fig

46、ure 1).10 Character definition and tolerances10.1 Definitions10.1.1 StrokeOne or more segments.10.1.2 Segment height, hThe distance between the top and bottom of that segment.10.1.3 Stroke height, MThe sum of the heights of the segments contained in that stroke. ISO 2013 All rights reserved 5BS ISO

47、1004-2:2013ISO 1004-2:2013(E)10.1.4 Character height, HcThe distance between the top and bottom of that character.10.1.5 Font height, HfThe nominal height of the highest character of the font.10.2 Stroke edge zones and mean edges10.2.1 Printed edge zonePrinted edge zones are located at both edges of

48、 all strokes, each one being defined by two parallel lines having a fixed distance the printed edge zone width b from each other. The value of b is 0,06 mm.There are 14 printed edge zones in a character. Each printed edge zone extends over the full height of the stroke, excluding inter segment inter

49、ruptions and segment end zones.10.2.2 Mean edgeThe centre line of the printed edge zone dividing the irregularities of the printed edge, contained in the printed edge zone, in such a way that the sum of the non-inked areas on the stroke side is equal to the sum of the inked areas on the space side. If this sum is minimized, the centre line is then called theoretical mean edge.10.2.3 Theoretical mean edgeThe 14 theoretical mean edges of a character are used to determine the skew angle of the character (see 10.3); in this