BS IEC 62873-3-2-2016 Residual current operated circuit-breakers for household and similar use Particular requirements for RCDs with flat quick-connect terminations《家用和类似用途的剩余电流动作断.pdf

《BS IEC 62873-3-2-2016 Residual current operated circuit-breakers for household and similar use Particular requirements for RCDs with flat quick-connect terminations《家用和类似用途的剩余电流动作断.pdf》由会员分享，可在线阅读，更多相关《BS IEC 62873-3-2-2016 Residual current operated circuit-breakers for household and similar use Particular requirements for RCDs with flat quick-connect terminations《家用和类似用途的剩余电流动作断.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、Residual current operated circuit-breakers for household and similar usePart 3-2: Particular requirements for RCDs with flat quick-connect terminationsBS IEC 62873-3-2:2016BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06National forewordThis British Standard is the U

2、K implementation of IEC 62873-3-2:2016.The UK participation in its preparation was entrusted by TechnicalCommittee PEL/23, Electrical accessories, to Subcommittee PEL/23/1, Circuitbreakers and similar equipment for household use.A list of organizations represented on this committee can be obtained o

3、nrequest to its secretary.This publication does not purport to include all the necessary provisions ofa contract. Users are responsible for its correct application. The British Standards Institution 2016.Published by BSI Standards Limited 2016ISBN 978 0 580 83056 3ICS 29.120.50Compliance with a Brit

4、ish Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 September 2016.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS IEC 62873-3-2:2016IEC 62873-3-2 Edi

5、tion 1.0 2016-09 INTERNATIONAL STANDARD Residual current operated circuit-breakers for household and similar use Part 3-2: Particular requirements for RCDs with flat quick-connect terminations INTERNATIONAL ELECTROTECHNICAL COMMISSION ICS 29.120.50 ISBN 978-2-8322-3614-7 Registered trademark of the

6、International Electrotechnical Commission Warning! Make sure that you obtained this publication from an authorized distributor. BS IEC 62873-3-2:2016 2 IEC 62873-3-2:2016 IEC 2016 CONTENTS FOREWORD . 3 INTRODUCTION . 5 1 Scope 6 2 Normative references. 6 3 Terms and definitions 6 4 Classification .

7、7 5 Characteristics of RCDs . 7 6 Marking and other product information . 7 7 Standard conditions for operation in service and for installation 7 8 Requirements for construction and operation 8 8.1 General . 8 8.2 Terminals for external conductors 8 9 Tests . 11 9.1 General . 11 9.2 Mechanical overl

8、oad-force . 11 Bibliography . 13 Figure 1 Dimensions of male tabs 9 Figure 2 Dimensions of round dimple detents (see Figure 1) . 10 Figure 3 Dimensions of rectangular dimple detents (see Figure 1) . 10 Figure 4 Dimensions of hole detents . 10 Figure 5 Dimensions of female connectors . 11 Figure 6 Ex

9、ample of position of the thermocouple for measurement of the temperature-rise . 12 Table 1 Colour code of female connectors in relationship with the cross-section of the conductor 7 Table 2 Dimensions of tabs 8 Table 3 Dimensions of female connectors . 11 Table 4 Overload test forces 12 BS IEC 62873

10、-3-2:2016IEC 62873-3-2:2016 IEC 2016 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ RESIDUAL CURRENT OPERATED CIRCUIT-BREAKERS FOR HOUSEHOLD AND SIMILAR USE Part 3-2: Particular requirements for RCDs with flat quick-connect terminations FOREWORD 1) The International Electrotechnical Commission (IEC)

11、is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition t

12、o other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in

13、 the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with condi

14、tions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC Nati

15、onal Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the wa

16、y in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC

17、 Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. I

18、EC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of it

19、s technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any oth

20、er IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the

21、 subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 62873-3-2 has been prepared by subcommittee 23E: Circuit breakers and similar equipment for household use, of IEC technical committee 23: Electrical accessories. The

22、 text of this standard is based on the following documents: FDIS Report on voting 23E/965/FDIS 23E/983/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/

23、IEC Directives, Part 2. BS IEC 62873-3-2:2016 4 IEC 62873-3-2:2016 IEC 2016 A list of all parts of the IEC 62873 series published under the general title Residual current operated circuit-breakers for household and similar use can be found on the IEC website. The committee has decided that the conte

24、nts of this publication will remain unchanged until the stability date indicated on the IEC website under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. A bilingual vers

25、ion of this publication may be issued at a later date. BS IEC 62873-3-2:2016IEC 62873-3-2:2016 IEC 2016 5 INTRODUCTION This document is part of the series described in the outline document IEC 62873-1. BS IEC 62873-3-2:2016 6 IEC 62873-3-2:2016 IEC 2016 RESIDUAL CURRENT OPERATED CIRCUIT-BREAKERS FOR

26、 HOUSEHOLD AND SIMILAR USE Part 3-2: Particular requirements for RCDs with flat quick-connect terminations 1 Scope This part of IEC 62873 applies to RCDs equipped with flat quick-connect terminations consisting of a male tab (see 3.2) with nominal width 6,3 mm and thickness 0,8 mm, to be used with a

27、 mating female connector for connecting electrical copper conductors according to the manufacturers instructions, for rated currents up to and including 16 A. NOTE The use of RCDS with flat quick-connect terminations for rated currents up to and including 20 A is accepted in BE, FR, IT, ES, PT and U

28、S. This part of IEC 62873 cannot be used alone but is intended to be applied together with an RCD product standard (IEC 61008-1 or IEC 61009-1) if an RCD is equipped with flat quick-connect terminations. The connectable electrical copper conductors are flexible, having a cross-sectional area up to a

29、nd including 4 mm2, or rigid stranded, having a cross-sectional area up to and including 2,5 mm2(AWG equal to or greater than 12). This part of IEC 62873 applies exclusively to RCDs having male tabs as an integral part of the device. 2 Normative references The following documents, in whole or in par

30、t, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 61008-1, Residual current operated circuit-bre

31、akers without integral overcurrent protection for household and similar uses (RCCBs) Part 1: General rules IEC 61009-1, Residual current operated circuit-breakers with integral overcurrent protection for household and similar uses (RCBOs) Part 1: General rules IEC 61210, Connecting devices Flat quic

32、k-connect terminations for electrical copper conductors Safety requirements IEC 62873-2, Residual current operated circuit-breakers for household and similar use Part 2: Residual current devices (RCDs) Vocabulary 3 Terms and definitions For the purposes of this document, the terms and definitions gi

33、ven in IEC 62873-2 and the following apply. BS IEC 62873-3-2:2016IEC 62873-3-2:2016 IEC 2016 7 3.1 flat quick-connect termination electrical connection consisting of a male tab and a female connector which can be pushed into and withdrawn with or without the use of a tool 3.2 male tab portion of a q

34、uick-connect termination which receives the female connector 3.3 female connector portion of a quick-connect termination which is pushed onto the male tab 3.4 detent dimple (depression) or hole in the male tab which engages a raised portion on the female connector to provide a latch for the mating p

35、arts 4 Classification Clause 4 of the RCD product standard applies. 5 Characteristics of RCDs Clause 5 of the RCD product standard applies. 6 Marking and other product information In addition to Clause 6 of the RCD product standard, the following requirements apply. The following information regardi

36、ng the female connector according to IEC 61210 and the type of conductor to be used shall be given in the manufacturers instructions: manufacturers name or trade mark; type reference; information on cross-sections of conductors and colour codes of insulated female connectors (see examples in Table 1

37、 below); the use of only silver- or tin-plated copper alloys. Table 1 Colour code of female connectors in relationship with the cross-section of the conductor Cross-section of the conductor Colour code of the female connector mm21 Red 1,5 Red or blue 2,5 Blue or yellow 4 Yellow 7 Standard conditions

38、 for operation in service and for installation Clause 7 of the RCD product standard applies. BS IEC 62873-3-2:2016 8 IEC 62873-3-2:2016 IEC 2016 8 Requirements for construction and operation 8.1 General Clause 8 of the RCD product standard applies, with the following exceptions: Subclause 8.1.3 appl

39、ies, the female connectors being fitted to the male tabs of the RCD. Subclause 8.1.5 does not apply. In addition, the following requirements apply. 8.2 Terminals for external conductors 8.2.1 Male tabs and female connectors shall be of a metal having mechanical strength, electrical conductivity and

40、resistance to corrosion adequate for their intended use. NOTE Silver- or tin-plated copper alloys are examples of suitable solutions. 8.2.2 The nominal width of the male tab is 6,3 mm and the thickness 0,8 mm, applicable to rated currents up to and including 16 A. NOTE 1 The use for rated currents u

41、p to and including 20 A is accepted in BE, FR, IT, PT, ES and US. The dimensions of the male tab shall comply with those specified in Table 2 and in Figure 1, Figure 2, Figure 3 and Figure 4, where the dimensions A, B, C, D, E, F, J, M, N, P and Q are mandatory. The dimensions of the female connecto

42、r which may be fitted on the male tab are given in Figure 5 and in Table 3. The shapes of the various parts may deviate from those given in the figures, provided that the specified dimensions are not influenced and the test requirements are complied with (for example: corrugated tabs, folded tabs, e

43、tc). Compliance is checked by inspection and by measurement. 8.2.3 Male tabs shall be securely retained. Compliance is checked by the mechanical overload test of 9.2. Table 2 Dimensions of tabs Nominal size mm Dimension A B min. C D E F J M N P Q min. 6,3 0,8 Dimple 1,0 0,84 6,40 4,1 2,0 12 2,5 2,0

44、1,8 0,7 7,8 0,77 6,20 3,6 1,6 8 2,2 1,8 0,7 8,9 Hole 1,0 0,84 6,40 4,7 2,0 12 1,8 0,5 7,8 0,77 6,20 4,3 1,6 8 0,7 8,9 NOTE 1 For the dimensions A to Q, refer to Figure 1 to Figure 4. NOTE 2 Where two values are shown in one column, they give the maximum and the minimum dimensions. BS IEC 62873-3-2:2

45、016IEC 62873-3-2:2016 IEC 2016 9 Bevel A of 45 need not be a straight line if it is within the confines shown. Dimension L is not specified and may vary by the application (for example fixing). Dimension C of tabs may be produced from more than one layer of material provided that the resulting tab c

46、omplies in all respects with the requirements of this standard. A radius on the longitudinal edge of the tab is permissible. The thickness C of the male tab may vary beyond Q or beyond B + 1,14 mm (0,045 in). All portions of the tabs are flat and free of burrs or raised plateaus, except that there m

47、ay be a raised plateau over the stock thickness of 0,025 mm (0,001 in) per side, in an area defined by a line surrounding the detent and distant from it by 1,3 mm (0,051 in). NOTE The sketches are not intended to govern the design except with regard to the dimensions shown. Figure 1 Dimensions of ma

48、le tabs IEC E A D45 approx. Q Centre of detent Centre of detent Centre of detent E A D45 approx. B L1,14 mm min. (0,045 in) min. Optional shoulder CCJ J CJ E A P DQ Alternative bevel BS IEC 62873-3-2:2016 10 IEC 62873-3-2:2016 IEC 2016 Detent shall be located within 0,076 mm (0,003 in) of the centre

49、-line of the tab. Figure 2 Dimensions of round dimple detents (see Figure 1) Detent shall be located within 0,13 mm (0,005 in) of the centre-line of the tab. Figure 3 Dimensions of rectangular dimple detents (see Figure 1) Detent shall be located within 0,076 mm (0,003 in) of the centre-line of the tab. Figure 4 Dimensions of hole detents IEC 0,076 mm min. (0,003 in) min. 0,076 mm min. (0,003 in) min. Radius Section X-X X X FIEC 0,076 mm